Mitsubishi Electronics WL639U Viewing computer images, Plugging the power cord, About DDC

Page 14

Viewing computer images (continued)

About DDC

The COMPUTER/COMPONENT VIDEO IN-1 terminal of this projector complies with the DDC1/2B standard and the COMPUTER/COMPONENT VIDEO DVI-D (HDCP) terminal complies with the DDC2B standard. When a computer supporting this standard is connected to this terminal, the computer will automatically load the information from this projector and prepare for output of appropriate images.

•After connecting a computer supporting this standard to this terminal, plug the power cord of the projector in the wall outlet first, and then boot up the computer.

B. Plugging the power cord

Earthing terminal

1	Power cord (example)

1.Plug the attached power cord into the power cord inlet of this projector.

2.Plug the other end of the power cord into a power outlet.

•The power cords for use in the U.S. and Europe are included with this projector. Use the appropriate one for your country.

•This projector uses the power plug of 3-pin grounding type. Do not take away the grounding pin from the power

plug. If the power plug doesn’t fit your wall outlet, ask an electrician to change the wall outlet.

•The provided power cord for the U.S. is rated at 120 V. Never connect this cord to any outlet or power supply using other voltages or frequencies than rated. If you use a power supply using other voltage than rated, prepare an appropriate power cord separately.

•Use 100-240 V AC 50/60 Hz to prevent fire or electric shock.

•Do not place any objects on the power cord or do not place the projector near heat sources to prevent damage to the power cord. If the power cord should be damaged, contact your dealer for replacement because it may cause fire or electric shock.

•Do not modify or alter the power cord. If the power cord is modified or altered, it may cause fire or electric shock.

Caution:

•Plug in the power cord firmly. When unplugging, hold and pull the power plug, not the power cord.

•Do not plug in or out the power cord with your hand wet. It may cause electric shock.

EN-14

Image 14

Contents WL639 When using the projector in Europe Compliance NoticeContents Important safeguards Important safeguards Preparing your projector Checking accessoriesInserting the batteries into the remote control Control area Preparating your projectorOverview Terminal boardAbout the laser beam Remote controlBottom side Reception angle Using the remote controlOperational range of the remote control Front of projector Rear of projectorBasic setup Setting up your projectorSetting up the screen Adjusting the projection angleFront projection, ceiling mounting Setting up your projectorWall screen Rear projectionWhen the aspect ratio of the image is When the aspect ratio of the screen isWhen the aspect ratio of the image is 1610 Wxga Screen size and projection distanceConnecting the projector to a computer Viewing computer imagesAbout DDC Plugging the power cordViewing computer images Projecting images To stop projecting When connecting to a notebook computerExample of the setting procedure for external output AV muteWhen a TV tuner or VCR is connected Connecting the projector to video equipmentConnecting to a video player, etc Viewing video imagesViewing video images Plugging in the power cordConnecting to video equipment having a DVI-D terminal Projector + DVD player or Hdtv decoderProjecting images Volume from the speaker When projected images are distorted to a trapezoid Setting the aspect ratioHow to change the settings Gamma Mode Menu operationMenu operation How to set the menusAvailable settings in the menus Auto Power OFF Pink Black Board Lamp ModeAuto Power on On / OFF Mute Mode Black / ImageVideo Signal Password FunctionCinema Mode Auto Setup AutoSignal User menu FunctionLamp Time LOW ResolutionDescription InputTo adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To cancel the menuAbout color temperature Adjusting projected imagesTo adjust the tone of white Color Temp Color EnhancerEN-30 To adjust the vertical position LPF Progressive filterAdvanced features Setting of the image displayed during startup or mutingTo enable the password function Advanced featuresPassword function To cancel the password functionStill ExpandPicture in Picture PinP Operation Mouse remote controlProjector + computer with USB connector PageUp buttonConnection Supervising and controlling by computerMajor functions Normal condition IndicatorsPossible Solution Abnormal conditionInterval of lamp replacement Replacing the lampReplacing the lamp Reset of the lamp operation timeWhen removing the lamp from the ceiling-mounted projector To replace the lampCleaning of the projector and the ventilation slots MaintenanceCleaning of the air-filter Cleaning of the lensTroubleshooting No image appears on the screen Problem SolutionImages are not displayed correctly TroubleshootingProblem Solution Kensington Lock Images are not displayed correctly Problem SolutionOthers Problem Solution Specifications Replacement part Option/Not included in the boxSpecifications XGA85COMPUTER/COMPONENT Video IN-1/IN-2 DVI-D Hdcp ConnectorsDimension Drawings unit mm Mitsubishi Projector Contact Information