Mitsubishi Electronics XL5980LU Turning off the projector, Volume from the speaker, AV mute

Page 14

To operate projector power ON (Continue)

Turning off the projector

Use the following procedure to turn off the power. Don’t turn off the power by switching off the main power switch or disconnecting the power plug be- cause these methods may cause deterioration

in the lamp’s performance or failure in the product.

11.Press the POWER button.

The message “POWER OFF? YES : PRESS AGAIN” appears on the screen.

To exit this mode,press any button except the POWER button. (Some buttons on the remote control don’t work for exit from this mode.)

12.Press the POWER button again.

The light source lamp will go out. Though the light source lamp will go out at this second press of the POWER but- ton, the exhaust fan continues to operate for another 120 seconds to cool down the lamp and LCD panel. In this case, the lamp indicator will go out.

13.Turn off the main power switch, and the POWER indi- cator will go out.

In cases where the main power switch is accidentally turned off when either the intake/exhaust fan or the power source lamp is in operation, allow the unit to cool down for 10 minutes with the power turned off. Repeat step 3 when turning on the power source lamp. If the lamp does not turn on immediately, repeat this step two or three times. Replace the lamp if it should still fail to turn on.

AUTO POSITION button

When the image isn’t projected in the right position with COMPUTER selected as the image source, follow the steps below.

1.Project a bright image such as the “Trash” window on the full screen.

2.When the screen saver is running, turn it off.

3.Press the AUTO POSITION button.

If the image is still not in the right position, adjust the image position using the SIGNAL menu.

Volume from the speaker

Press the volume + or – button to change the volume from the speaker.

The volume control bar will appear on the screen.

VOLUME

15

The volume control bar will disappear about 4 seconds after releasing the volume buttons.

The volume buttons don’t work while the MENU selection bar or the MENU is being displayed.

When a high-level audio signal, such as a DVD audio signal, is supplied to the COMPUTER AUDIO IN terminal, the output from the speaker may be dis- torted.

AV mute

The image and audio signals are temporarily muted by pressing the MUTE button. To bring them back to their normal level, press the MUTE button again.

The audio from the AUDIO OUT jack is also muted by pressing the MUTE button.

If the MUTE MODE in the INSTALLATION menu is set to LOGO, the splash screen will appear by pressing the MUTE button.

Please contact your dealer or Mitsubishi sales office for further information.

You can alter the splash screen freely. Please contact your dealer or Mitsubishi sales office for further information.

The lamp mode becomes “LOW” during muting. Therefore, the display of LOGO will darken, which isn’t a failure.

Muting will be cancelled in 3 hours automatically for the purpose of protecting devices. However, when the mute mode has been set to “LOGO,” muting won’t be cancelled.

ANAMORPHIC mode

When playing DVD discs containing data of letterboxed image, press the 16:9 button. Exit the ANAMORPHIC mode, by pressing the 16:9 button again.

Caution:

When you have finished using this projector, wait 120 seconds for the exhaust fans to stop. Then turn off the main switch and unplug the power cord from the wall outlet, for safety purposes.

The lamp cannot be turned on again for 60 seconds after it was turned off for precautionary purposes. It will take another 60 seconds before the lamp indicator goes off. If you want to turn on the projector again, wait until the indicator is off, and then press the POWER button.

The exhaust fan rotates faster as the temperature around the projector rises.

When the temperature around the projector rises too high, the sign “TEMPERATURE!!” blinks red on the screen. If the temperature stays too high, the lamp will be go out automatically.

EN – 14

Image 14
Contents Please read it before using your projector L5980When using the projector in Europe Compliance NoticeContents Important safeguards It can lead to fire Lens may shift causing injury or damage to the projectorIt can lead to fire or electric shock If you use incorrect voltage, it can lead to fireOverview Terminal panelAbout the laser beam Using the wired remote control Using the remote controlBattery installation Operation area for wireless control systemFront projection Front projection, ceiling mount InstallationOrientation of the projector For XL5980U only. For XL5980LU, please refer toProjector + DVD player or Hdtv decoder Basic connectionsProjector + AV device About DDC Projector + ComputerFor Macintosh Preparing the projector for operation Adjusting the angle of projectionRotate the adjustment feet for fine adjustment Getting ready for projectionTo operate projector power on ConditionTurning off the projector Volume from the speakerAnamorphic mode AV mutePress the Enter button or button Menu operationBasic operation An externally connected power switch such as a breaker even Is off. Use the remote control to turn on the lampUse to adjust the horizontal position of the image Expand Mode .. Select the mode for enlarging screen. SeeAutomatically selected depending on the input signal. If Use to adjust the vertical position of the imageAdjusting the image Picture adjustmentUser memory for signal setting Color matrixColor temperature Adjustment from personal computerPicture in Picture PinP Advanced features for presentationExpand StillOperation Mouse remote controlProjector + computer with USB connector Projector + computer with Serial portHow to reset the operation time meter Lamp replacementInterval of the lamp replacement Cleaning the projector and the ventilation slots MaintenanceCleaning the air-filter Cleaning the lensHow to check battery level Procedure for setting the Anti-Theft Alarm deviceProcedure for changing batteries Insert dry cell batteries into the theft warning deviceTroubleshooting Problems Cause Possible SolutionsNormal condition IndicatorsUnusual temperature Abnormal conditionSpecifications Replacement part Option / Not included in the box ConnectorsDimensional drawings mm What’s included in the boxCGA70 With Long Throw Zoom Lens OL-X500LZ With Tele Throw Zoom Lens OL-X500TZWith Rear projection Short Throw OL-X500FR F2.5Mitsubishi Electric Corporation
Related manuals
Manual 32 pages 34.3 Kb