Mitsubishi Electronics XL5980LU user manual About the laser beam

Bottom side

Remote control

1

2

4

5		COMPUTER
		1	2
6	KEYSTONE	VIDEO
		1	2
7	ZOOM/FOCUS EXPAND		AUTOPOSITION
	VOLUME		LASER
8
9
10
11	MENU R-CLICK ENTER
12	P in P	STILL	16 : 9

	MUTE
13	LENS SHIFT

C A U T I O N

LASER RADIATION

DO NOT STARE INTO BEAM

EXPOSURELASER- TI O N I S E M I TDET THIS A P E R T URE	WAVE LENGTH : 640-660nm
	MAX OUTPUT :			1mW
	CLASS	2	LASER	PRODUCT
	Comp l ies w i t h	21	CFR, 1040. 10 and 1040. 11
	RAYONNEMENT LASER
	NE PAS REGARDER DANS LE FAISCEAU				RADIAÇÃO LASER
	APPAREIL A LASER DE CLASSE2				EVITAR A EXPOSIÇÃO AO FEIXE
	LASER-STRAHLUNG				APARELHO LASER DA CLASSE 2
	NICHT IN DEN STRAHL BLICKEN				POTÊNCIA MÁXIMA: 1mW
AVOID R A D I A FROM	LASER KLASSE 2				COMPRIMENTO DE ONDA: 640 - 660 nm
	RADIAZIONl LASER					MANUFACTURER : B
	NON GUARDARE NEL RAGGIO LUCE
	APPARECCHIO LASER DI CLASSE 2					MANUFACTURED
	WAVE LENGTH :640-660nm MAX OUTPUT:1mW					JANUARY 2003
	IEC60825-1:1993+A1:1997+A2:2001					MADE IN CHINA
	INTERLINK K.K.
	SHINODA BLDG 1-10-7 HIGASHIKANDA CHIYODA-KU,TOKYO 101-0031,JAPAN

1	1	Adjustment foot (Left/Right)
	2	Air inlet grille/Filter cover
	3	Lamp cover
	Caution:
2	Do not replace the lamp immediately after using the
	projector because the lamp has got extremely hot.
3
	1	Laser aperture
	2	Transmission window
	3	Wired remote control jack
	4	Indicator
	5	POWER button
3	6	KEYSTONE button
	7	ZOOM/FOCUS button
	8	+ , – (VOLUME) buttons
	9	Mouse pointer
	10	MENU button
23	11	STILL button
	12	PinP button
22
	13	LENS SHIFT button
21
	14	MUTE button (Audio/Video)
20	15	16 : 9 button
19	16	ENTER button
18	17	R-CLICK button (For mouse)
	18	Direction buttons
17	19	LASER button
	20	AUTO POSITION button
16	21	EXPAND button
15	22	VIDEO 1, 2 button
14	23	COMPUTER 1, 2 button
	24	Left click button (For mouse)

• The + and - buttons are used in the KEYSTONE and ZOOM/FOCUS adjustment and the EXPAND mode in addition to the volume control.

• Pressing the LASER button emits a laser beam. Even when you keep holding down the LASER button, it is emitted only one minute. To keep emitting it longer, press the LASER button again.

	• You can disable the LASER button to prevent laser
	radiation due to misuse of the button.
	How to disable the LASER button
	While holding the LASER button down, press the }
	button three times.
24	How to enable the LASER button
	While holding the LASER button down, press the {

button three times.

About the laser beam

This remote control is a Class 2 laser product. (Max. output : 1 mW, Wavelength

: 640-660 nm)

Beam Divergence : 6m distance about 10.0mm x 10.0mm (±6.0mm)

CAUTION :

•Pressing the LASER button on the remote control emits a laser beam. Do not look into the laser beam directly. Do not point the laser beam at anyone. Looking at the laser beam directly may damage eyesight.

•Use of controls or adjustments or procedures other than those specified herein may result in hazardous radiation exposure.

•This remote controller cannot be repaired.

ENGLISH

EN – 7