Mitsubishi Electronics XD60U Using the Presentation Timer, E-31, General Operation, Timer Display

Page 32
Using the Presentation Timer

General Operation

Using the Presentation Timer

The presentation is given while checking the timer displayed on the screen.

The gauge display allows the remaining time to be known at a glance.

(1)Press the TIMER button to show the settings display. The display will close when an operation has not been made for about 10 seconds.

[Timer settings display]

Press the CANCEL button to close the display immediately.

(2)Use the ￿ and ￿ SELECT buttons to set the time.

The setting contents are “Off” and from 10 to 60 minutes (in

10-minute intervals)

Settings can also be made with the SELECT ￿￿ buttons.

(3)Press the ENTER button and start the timer.

The display of the timer setting will close, the display of the timer will appear and simultaneously the timer will start.

Gauge (Blue)

[Timer Display]

STANDBY

 

 

MENU

(2)

 

ENTER

 

RGB

 

 

VIDEO

CANCEL

 

QUICK

CANCEL button

 

 

Q

(3)

 

 

 

FREEZE

MUTE

LAMP MODE AUTO

1

2

3

4

 

 

 

ASPECT

VOL

KSTN

ZOOM

TIMER

 

 

 

(1)

The blue gauge indicates the remaining time. When the gauge disappears,the time is up.

The gauge continues to be displayed when the timer is stopped.

The gauge display allows the remaining time to be known at a glance. When the remaining time is “0” (Gray)

Press the ENTER button to restart the timer. The timer will start with the same time setting.

Press the CANCEL button to close the timer display. The timer setting will return to “Off”.

Moving the Position of the Timer Display

The SELECT ￿￿￿￿ buttons on the remote control permit move- ment within the movable range of the timer display.

Movable Range of the Timer Display

Note:

*The timer display will be closed while the menu or the quick menu is displayed, and while a message is displayed; however, the timer will still be operating at such times. Also, the timer will not be displayed unless a signal is being input.

*While the presentation timer is being displayed, screen movement will not be possible in the zoom mode.

E-31

Image 32
Contents XD60U User ManualDATA PROJECTOR MODELIMPORTANT SAFETY INFORMATION When using the projector in Europe COMPLIANCE NOTICEIMPORTANT SAFETY INFORMATION Do not look into the lens when it is operating Do not look into the air outlet grille when projector is operatingPlace of installation Unplug immediately if there is something wrong with your projectorMajor Features Lightweight at about 1.5 kg/3.3 lb high-intensity mobile projectorPowerful functions for presentations Lamp-mode switch function for the lamp outputTable of Contents Setup and ProjectionPreparation and Background Knowledge General OperationAdjustments and Settings Menu OperationsMiscellaneous Table of ContentsChecking the Supplied Accessories Remote control includes one button batteryPower cable 1.8 m / 5.9 feet No. 246C484-10/No. 246C484-20/No. 246C484-30Checking the Supplied Accessories Carrying case for projector and accessories“WARNING” Wash hands after handlingNames of the Main Unit Parts SOURCEBuilt-in Security Slot E-10PC connector E-15 AUDIO connector E-20Precautions Handling of the Remote Control Names of the Remote Control PartsE-11 Preparing the Remote Control Button Battery ReplacementRemote Control Range Using the remote control for the first timeThe Procedure Up to Projecting to the Screen E-134 Connecting the power cable and switching on the power When selecting the language of menu displays, etcE-14 Placement GuideScreen Size and Projection Distance Personal Computers with a DVI Connector Connections with Personal ComputerE-15 Connecting Personal Computers and Video EquipmentPersonal Computers with a Mini D-Sub 15-Pin Connector E-16Connecting Personal Computers and Video Equipment DVI/mini D-Sub 15-pin conversion cable Supplied itemTo Output the External Output Signal of a Notebook Computer E-17Manufacturer ModelConnections with Composite Signals Video Equipment with VIDEO ConnectorsVideo Equipment with S-VIDEO Connectors E-18Connections with Component Signals When the Video Equipment Has a YCbCr Connector or YPbPr ConnectorE-19 Projecting component signalsConnections with Audio Connectors E-20Audio cable Supplied item Audio conversion cableOperating E-21Power Cable Connections and Switching the Power On/Off 2 Switch on the projector powerWhen Menu Language Select is Displayed Upon Switching On the Power E-22Power Cable Connections and Switching the Power On/Off 2 Press the ENTER button to setSwitch off the power of the connected equipment Switch off the power of the projector3 Unplug the power cable FinishingAdjustment of the Projection Screen Adjustment of the Projection ScreenE-24 2 Adjust the projection image to the screenMaking Adjustments with the Adjusters E-25Adjustment of the Projection Screen 3 Turn the focus ring and adjust the focus of the screenAutomatic Adjustment of Analog RGB General OperationInput Selection E-26Selection of Aspect Ratio E-27Personal Computer Signal Video Signals / Component SignalsCancelling Video and Audio Temporarily Freezing a Moving PictureLamp Mode E-28Adjustment of the Volume KeystoneE-29 Adjustment MethodEnlargement of the Image and Video Movement The image can also be moved in the following circumstancesE-30 1 Press the ZOOM button to enlarge the imageUsing the Presentation Timer E-31Timer settings display 3 Press the ENTER button and start the timerProtecting the Projector with the Security Lock E-32Registering the password To cancel the number you have input, press the CANCEL buttonE-33 If the password input display appears when the power is turned onInput the password using the number buttons 1 to Canceling the password/Changing the passwordUsing the Quick Menu Content of Adjustments and SettingsE-34 This function permits frequently used adjustments to be performedMenu Operation Method Names and Functions of Buttons Used for Menu OperationsE-35 Remote ControlMenu Screen Names and Functions E-36Item Name This is the name of the ad- justment or setting Adjustment Bar and Settings ContentsPerforming Menu Operations Menu Display 1 Press the MENU button to display the menuSelection of the Menu Name 2 Press the SELECT button to select the menu nameMaking Adjustments/Settings Displaying the Cursor3 Press the SELECT button to display the item name selection cursor Selection of the Item NameE-39 Selecting Another Menu Name with Remote Control OperationClosing the Menu 6 Press the MENU button and close the menu display List of Item Names Offering Input Selection and Adjustments/Settings E-40The color space can only be adjusted with high definition TVs Menu nameE-41 TerminalPicture Adj. Picture Adjustment ImageBrightness / Contrast / Color / Tint / Sharpness Picture Adj. / Fine Picture / H Position / V PositionReset Fine PictureH Position V PositionColor Quick Color AdjGamma E-44Color Temp WhiteColor Space E-45White Balance E-46View AspectFilter E-47Vertical Flip/Horizontal Flip Keystone SaveE-48 The menus and other on-screen displays cannot be adjustedSetup Auto Power OffAuto Source Menu PositionPresentation Timer Input FormatE-50 SetupOption LanguageOn Screen BackgroundStartup Screen Security LockE-52 OptionFactory Default Lamp Timer ResetInfo StatusResolution / Frequency Lamp TimerE-54 This displays the lamp timerWhen an Indicator is Lit or Blinking Thermal ProtectorE-55 Indicator statusTroubleshooting Check the following matters before requesting servicingE-56 Problem Power does not turn onCleaning Cleaning a Soiled Projector Main UnitCleaning the Inside of the Projector Dirty LensReplacing the Lamp Cartridge E-58E-59 1 Unplug the power cord 2 Turn the projector upside-downReplacing the Lamp Cartridge 3 Remove the lamp coverE-60 7 Reset the Lamp Timer5 Mount the new lamp cartridge 6 Mount the lamp coverSpecifications E-61Optical ElectricalSignal Table of Supported FrequenciesE-62 AUTO Cabinet DimensionsE-63 MITSUBISHI ELECTRIC CORPORATION 1 Zusho Baba, Nagaokakyo-City, Kyoto Japan