Mitsubishi Electronics XD60U user manual Replacing the Lamp Cartridge, E-58

Page 59

Replacing the Lamp Cartridge

Replacing the Lamp Cartridge

•The lamp that is used as a light source in the projector has a limited service life. The rated service life of the lamp is about 1500 hours (when used in normal mode only). This could be shortened depending on conditions of use and other factors.

Note that lamp life will be extended when the projector is often used in Low mode. (The rated service life of the lamp means the average value of lamp life for lamps that have been manufactured over a long period, and it is derived from test conditions at this company.)

•When the life of the lamp is exceeded, the STATUS indicator lights a steady red and the message [Replace the Lamp Cartridge] is displayed on the screen. When this occurs, it is time to replace the lamp cartridge. Please make the replacement following the procedure below.

•If the projector is used another 100 hours after the lamp’s service life is reached, the power is set to the standby mode and no longer turns on.

•Contact a store that sells the XD60U for a replacement lamp. Indicate you need a VLT-XD50LP replacement lamp for the XD60U (order code 915P018-10).

CAUTION

•Replacement of the lamp cartridge is performed after switching off the power, waiting for the cooling fan to stop, disconnecting the power plug from the power outlet, and then leaving the projector for about 60 minutes before replacement is started. Replacement of the lamp cartridge during operation or immediately after operation stops will cause burns because of the high temperature.

•Do not remove any screws other than those specified.

•Do not touch the lamp with bare hands. Doing so could shorten the life of the lamp.

•If lamp has reached the end of its usable life, the lamp bulb may shatter. When this happens, an explosive sound can be heard and pieces of glass may be scattered in the lamp cartridge. Do not touch them as the pieces of glass may cause injury. If this happens, contact your dealer or the store the projector was purchased.

E-58

Image 59

Contents MODEL XD60UUser Manual DATA PROJECTORWhen using the projector in Europe COMPLIANCE NOTICE IMPORTANT SAFETY INFORMATIONIMPORTANT SAFETY INFORMATION Unplug immediately if there is something wrong with your projector Do not look into the lens when it is operatingDo not look into the air outlet grille when projector is operating Place of installationLamp-mode switch function for the lamp output Major FeaturesLightweight at about 1.5 kg/3.3 lb high-intensity mobile projector Powerful functions for presentationsGeneral Operation Table of ContentsSetup and Projection Preparation and Background KnowledgeTable of Contents Adjustments and SettingsMenu Operations MiscellaneousNo. 246C484-10/No. 246C484-20/No. 246C484-30 Checking the Supplied AccessoriesRemote control includes one button battery Power cable 1.8 m / 5.9 feetWash hands after handling Checking the Supplied AccessoriesCarrying case for projector and accessories “WARNING”SOURCE Names of the Main Unit PartsAUDIO connector E-20 Built-in Security SlotE-10 PC connector E-15Precautions Handling of the Remote Control Names of the Remote Control PartsE-11 Using the remote control for the first time Preparing the Remote ControlButton Battery Replacement Remote Control RangeWhen selecting the language of menu displays, etc The Procedure Up to Projecting to the ScreenE-13 4 Connecting the power cable and switching on the powerE-14 Placement GuideScreen Size and Projection Distance Connecting Personal Computers and Video Equipment Personal Computers with a DVI ConnectorConnections with Personal Computer E-15DVI/mini D-Sub 15-pin conversion cable Supplied item Personal Computers with a Mini D-Sub 15-Pin ConnectorE-16 Connecting Personal Computers and Video EquipmentModel To Output the External Output Signal of a Notebook ComputerE-17 ManufacturerE-18 Connections with Composite SignalsVideo Equipment with VIDEO Connectors Video Equipment with S-VIDEO ConnectorsProjecting component signals Connections with Component SignalsWhen the Video Equipment Has a YCbCr Connector or YPbPr Connector E-19Audio conversion cable Connections with Audio ConnectorsE-20 Audio cable Supplied item2 Switch on the projector power OperatingE-21 Power Cable Connections and Switching the Power On/Off2 Press the ENTER button to set When Menu Language Select is Displayed Upon Switching On the PowerE-22 Power Cable Connections and Switching the Power On/OffFinishing Switch off the power of the connected equipmentSwitch off the power of the projector 3 Unplug the power cable2 Adjust the projection image to the screen Adjustment of the Projection ScreenAdjustment of the Projection Screen E-243 Turn the focus ring and adjust the focus of the screen Making Adjustments with the AdjustersE-25 Adjustment of the Projection ScreenE-26 Automatic Adjustment of Analog RGBGeneral Operation Input SelectionVideo Signals / Component Signals Selection of Aspect RatioE-27 Personal Computer SignalE-28 Cancelling Video and Audio TemporarilyFreezing a Moving Picture Lamp ModeAdjustment Method Adjustment of the VolumeKeystone E-291 Press the ZOOM button to enlarge the image Enlargement of the Image and Video MovementThe image can also be moved in the following circumstances E-303 Press the ENTER button and start the timer Using the Presentation TimerE-31 Timer settings displayTo cancel the number you have input, press the CANCEL button Protecting the Projector with the Security LockE-32 Registering the passwordCanceling the password/Changing the password E-33If the password input display appears when the power is turned on Input the password using the number buttons 1 toThis function permits frequently used adjustments to be performed Using the Quick MenuContent of Adjustments and Settings E-34Remote Control Menu Operation MethodNames and Functions of Buttons Used for Menu Operations E-35Adjustment Bar and Settings Contents Menu Screen Names and FunctionsE-36 Item Name This is the name of the ad- justment or setting2 Press the SELECT button to select the menu name Performing Menu OperationsMenu Display 1 Press the MENU button to display the menu Selection of the Menu NameSelection of the Item Name Making Adjustments/SettingsDisplaying the Cursor 3 Press the SELECT button to display the item name selection cursorE-39 Selecting Another Menu Name with Remote Control OperationClosing the Menu 6 Press the MENU button and close the menu display Menu name List of Item Names Offering Input Selection and Adjustments/SettingsE-40 The color space can only be adjusted with high definition TVsTerminal E-41Picture Adj. / Fine Picture / H Position / V Position Picture Adj. Picture AdjustmentImage Brightness / Contrast / Color / Tint / SharpnessV Position ResetFine Picture H PositionE-44 ColorQuick Color Adj GammaE-45 Color TempWhite Color SpaceE-46 White BalanceE-47 ViewAspect FilterThe menus and other on-screen displays cannot be adjusted Vertical Flip/Horizontal FlipKeystone Save E-48Menu Position SetupAuto Power Off Auto SourceSetup Presentation TimerInput Format E-50Background OptionLanguage On ScreenOption Startup ScreenSecurity Lock E-52Status Factory DefaultLamp Timer Reset InfoThis displays the lamp timer Resolution / FrequencyLamp Timer E-54Indicator status When an Indicator is Lit or BlinkingThermal Protector E-55Problem Power does not turn on TroubleshootingCheck the following matters before requesting servicing E-56Dirty Lens CleaningCleaning a Soiled Projector Main Unit Cleaning the Inside of the ProjectorE-58 Replacing the Lamp Cartridge3 Remove the lamp cover E-591 Unplug the power cord 2 Turn the projector upside-down Replacing the Lamp Cartridge6 Mount the lamp cover E-607 Reset the Lamp Timer 5 Mount the new lamp cartridgeElectrical SpecificationsE-61 OpticalSignal Table of Supported FrequenciesE-62 AUTO Cabinet DimensionsE-63 1 Zusho Baba, Nagaokakyo-City, Kyoto Japan MITSUBISHI ELECTRIC CORPORATION