Mitsubishi Electronics XD20A user manual I n g t h e u n i t, Connect the power cord

Page 14

E – 14

O p e r a t i o n

U s i n g t h e u n i t

Before Using

Open the sliding lens cap.

1 Connect the power cord.

The POWER indicator will light amber, the ex- haust fan will operate at slow speed and the standby status will be activated.

Lights in amber (Standby)

POWER STATU

POWER SO

					VIDEO
					EO
					S VID
		RGB	/ YCbC	r	1
			/ YCbC
	USE
	USE
AUDIO	MO
Power cable
(supplied)					2 To wall
					outlet

2 Press POWER on the remote control, or POWER on top of the unit, to turn on the unit.

The POWER indicator on top of the unit turns to green and starts flashing.

It takes one minute for the unit to be ready for use. Wait until the indicator stops flashing and lights steadily in green.

MOUSE POWER

MENU

VIDEORGB

CANCEL

Green light flashes (About one minute)

↓

		Then lights steadily
POWER	ST	in green
	POWER

Note

While the POWER indicator is flashing, the unit doesn’t turn off even if you press POWER on the remote control, or POWER on the unit.

3 Turn on the connected source (computer, VCR, DVD player, etc.).

If you use a video component, start playback for screen/image adjustment.

4 Select the input by pressing either the VIDEO or RGB button of the remote con- trol, or the SOURCE button of this device (refer to page 16).

MOUSE POWER

MENU

VIDEO

RGB

SOURCE

CANCEL

Notes

•If the blue or black screen (the background type differs depending on the “BACKGROUND” setting. See page 28.) is projected, check the following:

–Is the source properly connected to the unit?

–Is the source component or computer turned on?

–Are the video signals coming to the unit?

•The video resolution of the connected computer can be changed. See page 13.

5 Adjust the position and height of the unit.

Move the unit to the position where the projected image is horizontally centered to the screen.

•When the projected image is offset horizontally

Adjust the position of the unit so that the unit is

square to the screen.
View from the top	Screen

•When the projected image is offset ver- tically

Adjust the height balance of the unit with the adjusters. See next page.

Side view

Screen

(Continued on next page.)

Image 14

Contents Data Projector Installation PrecautionsImportant Safeguards Power SupplyB l e o f c o n t e n t s E c k i n g t h e P p l i e d a c c e s s o r i e s Power cable mains lead 1.8 m/5.9 ftA t u r e s RGB cable Audio cable 3.3 ftInserting the batteries Remote control effective rangeE p a r i n g t h e M o t e c o n t r o l Quick Start GuideBottom R t s a n d c o n t r o l sTop, front and side panel view Rear and side panel view Audio jack 10, 11, 12 RGB/YCbCr connector 11Mouse connector Built-in Security SlotMute button Enter button 17 Infrared transmitterAuto button Freeze button Screen height InstallationInstallation Guidelines normal installation Screen sizeRear panel jacks of this device N n e c t i n g v i d e o e q u i p m e n tConnection to the Video jack of the unit Connection to the S-VIDEO jack of the unitConnection to the RGB/YCbCr connector N n e c t i n g a P C o r M a c i n t o s h Windows Changing the computer’s video resolutionsWindows 98/Windows MacintoshI n g t h e u n i t Connect the power cordAdjust the position and height of the unit Turn on the connected source computer, VCR, DVD player, etcCase of RGB input, adjust the video of the connected PC After using the unit I n g t h e u n i t N t i n u e dIBM PS/2 Mouse Port Connection Remote control mouse functionsUSB Port Connection Keystone Adjustment Automatic Screen AdjustmentAdjusting the Volume Freezing animated imagesScreen Reduction To move to the desired portion of the enlarged pictureEnlarging the picture Press the desired portion of the cursor keyN u S t r u c t u r e Common menuNormal menu RGB input Advanced menu To select other menu names Press the cursor / keys to adjust the sharpnessJ u s t i n g t h e p i c t u r e e l e m e n t s To close the menuTiming Chart If no images appear during setting Adjusting Clock Frequency and PhaseAdjusting the position of the image S e t t i n g ResettingResetting the time the hours of lamp usage S e t t i n g t h e L a m p H o u r s o f U s a g eT t i n g N a r r o w I m a g e s a d v a n c e d M e n u Setting the Cinema ModeAdjusting Color Balance Selecting the Color SystemSetting Filter Setting the RGB/YCbCr connectorSetting the Display Frame Audio Muting Setting the partial display positionI t i a l S e t t i n g s Selecting the BackgroundSelecting a Projection Type Auto Source SettingsUsing the Power Saving Function T t i n g t h e M e n u Troubleshooting Status indicator Status Light MessagesR t r i d g e Lamp cartridge replacement procedureP l a c i n g t h e l a m p StepOptical Specification sSub Pin Assignments ElectricalMm/7.0″ Dimensions230 mm/9.0″ 177