Mitsubishi Electronics XD20A user manual I n g t h e u n i t N t i n u e d, After using the unit

Page 16

U s i n g t h e u n i t

( c o n t i n u e d )

9 Adjust the picture elements (see page 22), then select the picture type according to the video content (see page 26).

10 Start using the unit.

The following functions are available while using the unit:

•Adjusting the volume of the unit's speaker (see pages 18 and 28),

•Turning off the image and muting the sound temporarily (see page 18),

•Freezing a moving picture (see page 18),

•Enlarging the picture (see page 19)

Note

•When there is no signal input for a period of 5 min. or more, the power is automatically turned off and standby status is activated. (see page 29)

After using the unit

1 Press the POWER button of the remote control or the POWER button of the main unit for a few seconds.

The power will turn off and the POWER indicator will blink amber for 1 min., then the standby status will be activated. (The exhaust fan will continue to run for a while for cooling purposes.) Do not unplug the power cord while the indicator is blinking.

MOUSE

POWER

 

 

POWER

ST

MENU

 

POWER

VIDEO

RGB

 

CANCEL

 

 

Blinks amber (1 min.)

↓

Lights amber

Note

•The POWER switches of the remote control and main unit will not operate until the blinking stops.

•After the standby status is activated, wait 1 min. or more before turning the power on again. The power will not turn on until the 1 min. interval has elapsed.

•The exhaust fan will continue to run even in standby status.

2 Disconnect the power cord.

The POWER indicator will turn off.

U s i n g t h e R e m o t e C o n t r o l ( I n p u t S e l e c t i o n )

MOUSEPOWER

MENU

VIDEORGB

VIDEO button CANCEL RGB button

Operating from the main unit

Inputs can be selected not only by operating the remote control but also by using the main unit SOURCE button.

POWER STATUS

POWER SOURCE AUTO

SOURCE button

1 Press the VIDEO button.

The video signal (VIDEO, S-VIDEO) connected to the input jack of this device will be detected and projected automatically. If a video signal is not detected, the message NO SIGNAL will be displayed.

VIDEO

2 Press the RGB button.

The analog RGB signal connected to the input connector of this device will be detected and projected automatically.

(Component video will be detected if the RGB/ YCbCr connector is set (page 27) to YCbCr.) If a video signal is not detected, the message NO SIGNAL will be displayed.

RGB

Note

•All video signals input to this device will be detected if Auto Source (page 29) is set.

3 Press the SOURCE button.

The video signal (RGB or YCbCr, VIDEO, S- VIDEO) connected to the input jack of this device will automatically be detected and projected. If a video signal is not detected, the message NO SIGNAL will be displayed.

SOURCE

The signals are sensed repeatedly in the se- quence shown below.

→RGB/YCbCr

S-VIDEO ← VIDEO

Note

•When Auto Source (see page 29) is set to ON, all signals input to this projector will be sensed.

E – 16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Data Projector Precautions Important SafeguardsInstallation Power SupplyB l e o f c o n t e n t s Power cable mains lead 1.8 m/5.9 ft A t u r e sE c k i n g t h e P p l i e d a c c e s s o r i e s RGB cable Audio cable 3.3 ftRemote control effective range E p a r i n g t h e M o t e c o n t r o lInserting the batteries Quick Start GuideTop, front and side panel view R t s a n d c o n t r o l sBottom Audio jack 10, 11, 12 RGB/YCbCr connector 11 Mouse connectorRear and side panel view Built-in Security SlotAuto button Freeze button Enter button 17 Infrared transmitterMute button Installation Installation Guidelines normal installationScreen height Screen sizeN n e c t i n g v i d e o e q u i p m e n t Connection to the Video jack of the unitRear panel jacks of this device Connection to the S-VIDEO jack of the unitConnection to the RGB/YCbCr connector N n e c t i n g a P C o r M a c i n t o s h Changing the computer’s video resolutions Windows 98/WindowsWindows MacintoshConnect the power cord Adjust the position and height of the unitI n g t h e u n i t Turn on the connected source computer, VCR, DVD player, etcCase of RGB input, adjust the video of the connected PC After using the unit I n g t h e u n i t N t i n u e dUSB Port Connection Remote control mouse functionsIBM PS/2 Mouse Port Connection Automatic Screen Adjustment Adjusting the VolumeKeystone Adjustment Freezing animated imagesTo move to the desired portion of the enlarged picture Enlarging the pictureScreen Reduction Press the desired portion of the cursor keyN u S t r u c t u r e Common menuNormal menu RGB input Advanced menu Press the cursor / keys to adjust the sharpness J u s t i n g t h e p i c t u r e e l e m e n t sTo select other menu names To close the menuTiming Chart Adjusting the position of the image Adjusting Clock Frequency and PhaseIf no images appear during setting Resetting Resetting the time the hours of lamp usageS e t t i n g S e t t i n g t h e L a m p H o u r s o f U s a g eSetting the Cinema Mode Adjusting Color BalanceT t i n g N a r r o w I m a g e s a d v a n c e d M e n u Selecting the Color SystemSetting the Display Frame Setting the RGB/YCbCr connectorSetting Filter Setting the partial display position I t i a l S e t t i n g sAudio Muting Selecting the BackgroundUsing the Power Saving Function Auto Source SettingsSelecting a Projection Type T t i n g t h e M e n u Troubleshooting Status indicator Status Light MessagesLamp cartridge replacement procedure P l a c i n g t h e l a m pR t r i d g e StepSpecification s Sub Pin AssignmentsOptical ElectricalDimensions 230 mm/9.0″Mm/7.0″ 177
Top Page Image Contents