Mitsubishi Electronics XD460U Viewing computer images, Connecting the projector to a computer

Page 13

Viewing computer images

A. Connecting the projector to a computer

Preparation:

•Make sure that the power of the projector and that of the computer are turned off.

•When connecting the projector to a desktop computer, disconnect the RGB cable that is connected to the monitor.

ENGLISH

COMPUTER IN/

COMPONENT VIDEO IN

1

2 to monitor port RGB cable

DVI-D (HDCP)

For analog connection:

1.Connect one end of the supplied RGB cable to the COMPUTER IN/COMPONENT VIDEO IN-1/2 terminal of the projector.

2.Connect the other end of the RGB cable to the monitor port of the computer.

•Additional devices, such as a conversion connector and an analog RGB output adapter, are required depending on the type of the computer to be connected.

•When viewing images supplied from an analog-connected computer, press the COMPUTER button on the remote control.

•This projector does not support 3-line signals (SYNC-ON- GREEN signals).

For digital connection:

1

2	to DVI
2
	DVI cable

Computer

1.Connect one end of a commercially available DVI cable to the DVI-D (HDCP) terminal of the projector.

2.Connect the other end of the DVI cable to the DVI terminal of the computer.

•Additional devices, such as a conversion connector and an analog RGB output adapter, are required depending on the type of the computer to be connected.

•When viewing images supplied from a digital-connected computer, press the DVI-D(HDCP) button on the remote control.

For audio connection:

• Plug the power cord of the projector in the wall outlet ﬁrst,

and then boot up the computer.

• This projector uses stereo pin jack for its audio input. Check

the type of the audio output terminal of the connected

computer and prepare a proper cable for connection. Some

computers don't have the audio output terminal.

• Speaker output is mono.

AUDIO IN

PC audio cable (option)

AUDIO OUT

to PC audio output

• When the audio cable is connected to the AUDIO OUT ter-

minal, the speaker output is muted.

Monitor

For monitor connection:

1.Connect one end of the RGB cable that is connected to the MONITOR OUT terminal of the projector.

RGB cable

EN-13

Image 13

Contents XD490 XD460 Risk of Electric Shock Do not Open When using the projector in EuropeContents Important safeguards Do not look into the lens when it is operating Do not keep using the damaged projectorDo not unplug the power cord during op- eration Place of installationInserting the batteries into the remote control Checking accessoriesPreparing your projector Control panel OverviewTerminal board How to disable the Laser button Adjustment foot Front Lamp cover Adjustment feet RearHow to enable the Laser button Preparating your projector ContinueOperational range of the remote control Using the remote controlReception angle Front of projector Rear of projectorSetting up the screen Setting up your projectorBasic setup Adjusting the projection angleFront projection, ceiling mounting Wall screenRear projection When the aspect ratio of the screen is Setting up your projectorScreen size and projection distance Virtual lens shiftViewing computer images Connecting the projector to a computerViewing computer images Plugging the power cordProjecting images Example of the setting procedure for external output When connecting to a notebook computerTo stop projecting AV muteConnecting to a video player, etc Connecting the projector to video equipmentWhen a TV tuner or VCR is connected Viewing video imagesConnecting to video equipment having a DVI-D terminal Plugging in the power cordViewing video images Projector + DVD player or Hdtv decoderProjecting images Volume from the speaker How to change the settings Setting the aspect ratioWith the remote control With the Feature menuMenu operation How to set the menusInstallation menu Available settings in the menusSignal menu Feature menuMenu operation To adjust the brightness Contrast and Brightness Adjusting projected imagesTo adjust the color Color and Tint To cancel the menuTo adjust the tone of white Color Temp Adjusting projected imagesAbout color temperature Color EnhancerLPF Progressive ﬁlter To adjust the vertical positionPassword function Advanced featuresTo enable the password function To cancel the password functionTo use the PinP mode To use the Expand modeExpand To change the position of the sub imageProjector + computer with USB connector Advanced featuresUSB PageUP buttonReplacing the lamp Interval of lamp replacementCleaning of the lens Cleaning of the projector and the ventilation slotsReset of the lamp operation time Replacing the lampNo image appears on the screen Problem Solution TroubleshootingProblem Solution TroubleshootingImages are not displayed correctly Kensington Lock Others Problem SolutionNormal condition IndicatorsAbnormal condition Status ConditionSpeciﬁcations Replacement part Option / Not included in the boxDVI RCAXGA85 SpeciﬁcationsDimension Drawings unit mm ConnectorsMitsubishi Projector Contact Information