Mitsubishi Electronics XD460U user manual To stop projecting, Volume from the speaker

Page 20

Viewing video images (continued)

POWER button

POWER button

POWER STATUS

AUTO POSITION

COMPUTER KEYSTONE VIDEO

ENTER

VOLUME

MENU

To stop projecting:

8.Press the POWER button.

•A conﬁrmation message is displayed.

•To cancel the procedure, leave the projector for a while or press the MENU button.

9.Press the POWER button.

•The lamp goes out and the projector goes into a standby mode. In this standby mode, the POWER indicator blinks red.

10.Wait about one minute for the POWER indicator to be lit in red steadily.

•During this period of one minute in the standby mode, the intake fan and exhaust fan rotate to cool the lamp.

•The lamp can't be lit again for one minute after turned off for safety purpose. It will take another one minute for the STATUS indicator to go out. If you want to turn on the projector again, wait until the indicator goes out, and then press the POWER button.

•The air outlet fans rotate faster as the temperature around the projector rises.

•Do not unplug the power cord while the POWER indicator is blinking. Unplugging the power cord immediately after use may cause a breakdown.

•Though the fan makes loud sounds during cooling, such symptom is not a malfunction.

11.Unplug the power cord from the outlet.

•The POWER indicator will go out.

•If the power cord should be unplugged accidentally while either the air inlet fan or the air outlet fans are oper- ating or the lamp is on, allow the projector to cool down for 10 minutes with the power off. To light the lamp again, press the POWER button. If the lamp doesn't light up immediately, repeat pressing the POWER button two or three times. If it should still fail to light up, replace the lamp.

•Cover the lens with the lens cap to protect it from dust.

Volume from the speaker

Press the VOLUME + or - button to change the volume from the speaker.

The volume control bar will appear on the screen.

VOLUME

10

•The volume control bar will disappear about 10 seconds after the VOLUME button is released.

•The VOLUME buttons don't function while the menu selection bar or the menu is being displayed.

•When a high-level audio signal, such as a DVD audio signal, is supplied to the AUDIO IN terminal, the output from the speaker may be distorted.

EN-20

Image 20

Contents XD490 XD460 When using the projector in Europe Risk of Electric Shock Do not OpenContents Important safeguards Do not keep using the damaged projector Do not look into the lens when it is operatingDo not unplug the power cord during op- eration Place of installationPreparing your projector Checking accessoriesInserting the batteries into the remote control Terminal board OverviewControl panel Adjustment foot Front Lamp cover Adjustment feet Rear How to disable the Laser buttonHow to enable the Laser button Preparating your projector ContinueUsing the remote control Operational range of the remote controlReception angle Front of projector Rear of projectorSetting up your projector Setting up the screenBasic setup Adjusting the projection angleRear projection Wall screenFront projection, ceiling mounting Setting up your projector When the aspect ratio of the screen isScreen size and projection distance Virtual lens shiftConnecting the projector to a computer Viewing computer imagesPlugging the power cord Viewing computer imagesProjecting images When connecting to a notebook computer Example of the setting procedure for external outputTo stop projecting AV muteConnecting the projector to video equipment Connecting to a video player, etcWhen a TV tuner or VCR is connected Viewing video imagesPlugging in the power cord Connecting to video equipment having a DVI-D terminalViewing video images Projector + DVD player or Hdtv decoderProjecting images Volume from the speaker Setting the aspect ratio How to change the settingsWith the remote control With the Feature menuHow to set the menus Menu operationAvailable settings in the menus Installation menuMenu operation Feature menuSignal menu Adjusting projected images To adjust the brightness Contrast and BrightnessTo adjust the color Color and Tint To cancel the menuAdjusting projected images To adjust the tone of white Color TempAbout color temperature Color EnhancerTo adjust the vertical position LPF Progressive ﬁlterAdvanced features Password functionTo enable the password function To cancel the password functionTo use the Expand mode To use the PinP modeExpand To change the position of the sub imageAdvanced features Projector + computer with USB connectorUSB PageUP buttonInterval of lamp replacement Replacing the lampCleaning of the projector and the ventilation slots Cleaning of the lensReset of the lamp operation time Replacing the lampTroubleshooting No image appears on the screen Problem SolutionImages are not displayed correctly TroubleshootingProblem Solution Others Problem Solution Kensington LockIndicators Normal conditionAbnormal condition Status ConditionReplacement part Option / Not included in the box SpeciﬁcationsDVI RCASpeciﬁcations XGA85Connectors Dimension Drawings unit mmMitsubishi Projector Contact Information