Mitsubishi Electronics XD460U user manual Preparing your projector, Checking accessories

Page 6

Preparing your projector

Checking accessories

The following accessories are provided with this projector. Check to be sure that all of the accessories are packed in the package.

Cables

 

 

Mini D-SUB

D-SUB 9-pin

 

USB 4P

15-pin

 

 

 

(B type)

 

 

 

 

Mini D-SUB

8-pin

 

USB 4P

15-pin

 

 

 

(A type)

 

 

Audio/Video cable

USB cable

RGB cable for PC

RS-232C cable

(246C381-10)

(246C509-10)

(246C521-10)

(246C508-10)

• Used for projector control by computer.

Power supply parts

Power cord (two)

(246C483-10, 246C383-20)

Remote control parts

Remote control

R6 (Size-AA)

(290P136-10)

battery (two)

Others

Lens cap (Attached to the projector)

Quick Start up (857D064-90)

CD-ROM (919C137-50)

Safety manual (871D421-50)

Carrying case (772P044-10)

Important:

• The attached power cords are to be used exclusively for this product. Never use them for other products.

Inserting the batteries into the remote control

1

1.

Remove the rear lid of the remote control.

2.

Check the polarity (+), (-) of the batteries, and set them

 

3

correctly, inserting their (-) side first.

If the battery is inserted from the (+) side first, inserting the (-) side is difficult because the coil spring end hits on the battery side. If the battery is forced to insert in this

2

way, the outer label of the battery may get ripped and it

may cause a short-circuit and heating.

 

 

3. Attach the rear lid.

Important:

• Use two size-AA batteries (R6).

• Replace the two batteries with new ones when the remote control is slow to operate.

CAUTION:

Use of a battery of wrong type may cause explosion.

Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.

Dispose of used batteries according to your local regulations.

Batteries may explode if misused. Do not recharge, disassemble, or dispose of them in fire.

Be sure to handle the batteries according to the instructions.

Load the batteries with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.

Keep batteries out of reach of children and pets.

Remove the batteries, if the remote control is not used for a long time.

Do not combine a new battery with an old one.

If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in contact with your eyes, rinse them with water and then consult your doctor.

EN-6

Image 6
Contents XD490 XD460 When using the projector in Europe Risk of Electric Shock Do not OpenContents Important safeguards Do not unplug the power cord during op- eration Do not keep using the damaged projectorDo not look into the lens when it is operating Place of installationChecking accessories Inserting the batteries into the remote controlPreparing your projector Overview Control panelTerminal board How to enable the Laser button Adjustment foot Front Lamp cover Adjustment feet RearHow to disable the Laser button Preparating your projector ContinueReception angle Using the remote controlOperational range of the remote control Front of projector Rear of projectorBasic setup Setting up your projectorSetting up the screen Adjusting the projection angleWall screen Front projection, ceiling mountingRear projection Screen size and projection distance Setting up your projectorWhen the aspect ratio of the screen is Virtual lens shiftConnecting the projector to a computer Viewing computer imagesPlugging the power cord Viewing computer imagesProjecting images To stop projecting When connecting to a notebook computerExample of the setting procedure for external output AV muteWhen a TV tuner or VCR is connected Connecting the projector to video equipmentConnecting to a video player, etc Viewing video imagesViewing video images Plugging in the power cordConnecting to video equipment having a DVI-D terminal Projector + DVD player or Hdtv decoderProjecting images Volume from the speaker With the remote control Setting the aspect ratioHow to change the settings With the Feature menuHow to set the menus Menu operationAvailable settings in the menus Installation menuFeature menu Signal menuMenu operation To adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To cancel the menuAbout color temperature Adjusting projected imagesTo adjust the tone of white Color Temp Color EnhancerTo adjust the vertical position LPF Progressive filterTo enable the password function Advanced featuresPassword function To cancel the password functionExpand To use the Expand modeTo use the PinP mode To change the position of the sub imageUSB Advanced featuresProjector + computer with USB connector PageUP buttonInterval of lamp replacement Replacing the lampReset of the lamp operation time Cleaning of the projector and the ventilation slotsCleaning of the lens Replacing the lampTroubleshooting No image appears on the screen Problem SolutionTroubleshooting Problem SolutionImages are not displayed correctly Others Problem Solution Kensington LockAbnormal condition IndicatorsNormal condition Status ConditionDVI Replacement part Option / Not included in the boxSpecifications RCASpecifications XGA85Connectors Dimension Drawings unit mmMitsubishi Projector Contact Information