Mitsubishi Electronics XD460U user manual Preparating your projector Continue, Bottom side

Page 8

Preparating your projector (Continue)

Bottom side

1

2

1Adjustment foot (Front)

2Lamp cover

3Adjustment feet (Rear)

Caution:

Do not replace the lamp immediately after using the projector because the lamp would be extremely hot and it may cause burns.

Remote control

1

2

3

4

5

6

7

8

9

10

11

12

13

3

	1	2	27
	COMPUTER
DVI-D(HDCP)	VIDEO	S-VIDEO	26
			26
HOME	PageUP	AUTO POSITION	25
			25
END	PageDOWN	LASER	24
			24
			23
			22
			21
MENU	R-CLICK	ENTER	20
			20
		KEYSTONE	19
			19
VOLUME		ASPECT	18
			18
WALL SCREEN EXPAND		PinP	17
			17
CE	MUTE	STILL	16
			16

15

14

28

1Laser aperture

2Transmission window

3Indicator

4POWER button

5VIDEO button

6DVI-D(HDCP) button

7HOME button

8END button

9Mouse pointer

10MENU button

11+ , - (VOLUME) buttons

12WALL SCREEN button

13COLOR ENHANCER button

14MUTE button (Audio/Video)

15EXPAND button

16STILL button

17PinP button

18ASPECT button

19KEYSTONE button

20ENTER button

21R-CLICK button

22Direction buttons

23LASER button

24AUTO POSITION button

25Page UP/DOWN buttons

26S-VIDEO button

27COMPUTER 1, 2 buttons

28L-CLICK button

•The + and - buttons are used in the KEYSTONE adjustment and the EXPAND mode in addition to the volume control.

•Pressing the LASER button emits a laser beam. Even when you keep holding down the LASER button, it is emitted only one minute. To keep emitting it longer, press the LASER button again.

•You can disable the LASER button to prevent laser radiation due to misuse of the button.

How to disable the LASER button

While holding the LASER button down, press the button three times.

How to enable the LASER button

While holding the LASER button down, press the button three times.

•Whenever the batteries are replaced, the LASER button is enabled.

About the laser beam

This remote control is a Class 2 laser product. (Max. output : 1 mW, Wavelength : 620-640 nm)

Beam Divergence : 6m distance about 10.0mm x 10.0mm (±6.0mm)

CAUTION :

•Pressing the LASER button on the remote control emits a laser beam. Do not look into the laser beam directly. Do not point the laser beam at anyone. Looking at the laser beam directly may damage eyesight.

•Use of controls or adjustments or procedures other than those speciﬁed herein may result in hazardous radiation exposure.

•This remote controller cannot be repaired.

EN-8

Image 8

Contents XD490 XD460 When using the projector in Europe Risk of Electric Shock Do not OpenContents Important safeguards Do not keep using the damaged projector Do not look into the lens when it is operatingDo not unplug the power cord during op- eration Place of installationPreparing your projector Checking accessoriesInserting the batteries into the remote control Terminal board OverviewControl panel Adjustment foot Front Lamp cover Adjustment feet Rear How to disable the Laser buttonHow to enable the Laser button Preparating your projector ContinueUsing the remote control Operational range of the remote controlReception angle Front of projector Rear of projectorSetting up your projector Setting up the screenBasic setup Adjusting the projection angleRear projection Wall screenFront projection, ceiling mounting Setting up your projector When the aspect ratio of the screen isScreen size and projection distance Virtual lens shiftConnecting the projector to a computer Viewing computer imagesPlugging the power cord Viewing computer imagesProjecting images When connecting to a notebook computer Example of the setting procedure for external outputTo stop projecting AV muteConnecting the projector to video equipment Connecting to a video player, etcWhen a TV tuner or VCR is connected Viewing video imagesPlugging in the power cord Connecting to video equipment having a DVI-D terminalViewing video images Projector + DVD player or Hdtv decoderProjecting images Volume from the speaker Setting the aspect ratio How to change the settingsWith the remote control With the Feature menuHow to set the menus Menu operationAvailable settings in the menus Installation menuMenu operation Feature menuSignal menu Adjusting projected images To adjust the brightness Contrast and BrightnessTo adjust the color Color and Tint To cancel the menuAdjusting projected images To adjust the tone of white Color TempAbout color temperature Color EnhancerTo adjust the vertical position LPF Progressive ﬁlterAdvanced features Password functionTo enable the password function To cancel the password functionTo use the Expand mode To use the PinP modeExpand To change the position of the sub imageAdvanced features Projector + computer with USB connectorUSB PageUP buttonInterval of lamp replacement Replacing the lampCleaning of the projector and the ventilation slots Cleaning of the lensReset of the lamp operation time Replacing the lampTroubleshooting No image appears on the screen Problem SolutionImages are not displayed correctly TroubleshootingProblem Solution Others Problem Solution Kensington LockIndicators Normal conditionAbnormal condition Status ConditionReplacement part Option / Not included in the box SpeciﬁcationsDVI RCASpeciﬁcations XGA85Connectors Dimension Drawings unit mmMitsubishi Projector Contact Information