Mitsubishi Electronics XD480U user manual Installation, Layout of the projector, Rear projection

Page 9

Installation

Layout of the projector

Image size varies depending on the distance between the screen and the projector.

Front projection

Hd

H

L

W

AB

A=B

L: Between the screen and the front edge of the projector

Hd : Height of the projected image

ENGLISH

 

 

Screen

 

 

Distance from the screen : L

 

 

 

Diagonal size

Width : W

Height : H

Maximum

Minimum

Hd

 

 

 

 

 

 

 

zoom (WIDE)

zoom(TELE)

 

 

 

inch

cm

inch

cm

inch

cm

inch

m

inch

m

inch

 

cm

40

102

32

81

24

61

51

1.3

62

1.6

2.8

 

7.2

60

152

48

122

36

91

77

2.0

94

2.4

4.3

 

10.9

80

203

64

163

48

122

103

2.6

125

3.2

5.7

 

14.5

100

254

80

203

60

152

130

3.3

157

4.0

7.1

 

18.1

150

381

120

305

90

229

196

5.0

237

6.0

10.7

 

27.1

200

508

160

406

120

305

262

6.6

316

8.0

14.2

 

36.2

250

635

200

508

150

381

327

8.3

17.8

 

45.2

300

762

240

610

180

457

393

10.0

21.4

 

54.3

• The above figures are approximate and may be slightly different from the actual measurements.

Front projection, ceiling mounting

For ceiling mounting, you need the ceiling mount kit de- signed for this projector. Ask a specialist for installation. For details, consult your dealer.

The warranty on this projector does not cover any damage caused by use of any non-recommended ceiling mount kit or installation of the ceiling mount kit in an improper location.

When using the projector mounted on the ceiling, set IMAGE REVERSE in the INSTALLATION menu to MIRROR INVERT. See page 17.

When the projector is mounted on the ceiling, im- ages may appear darker than those projected in the case of tabletop mounting. This isn't a product malfunction.

Rear projection

Ask a specialist for installation. For details, consult your dealer.

For rear projection, set IMAGE REVERSE in the IN- STALLATION menu to MIRROR. See page 17.

Caution:

Placing the projector directly on a carpet impairs ventilation by the fans, causing damage or failure. Put a hard board under the projector to facilitate ventilation.

Place the projector at least 50 cm (or 20 inch) away from the wall to prevent the air inlet grille and the air outlet grilles that emit hot air from being blocked.

Do not use the projector in the following locations and manners, which may cause fire or electric shock.

In a dusty or humid place.

In a sideways or upside-down position.

Near a heater.

In an oily, smoky, or damp place such as a kitchen.

In direct sunlight.

Where the temperature rises high, such as in a closed car.

Where the temperature is lower than +41ºF (or +5ºC) or higher than +95ºF (or +35ºC ).

Important:

Do not apply force to the lens, because the lens may be damaged.

EN - 9

Image 9
Contents XD480 XD450 XD400 Risk of Electric Shock Do not Open When using the projector in EuropeContents Important safeguards Do not look into the lens when the projector is oper- ating Do not keep using the damaged projectorPlace of installation Never remove the cabinet Do not modify the projectorOverview Control panelTerminal board Adjustment foot Front Lamp cover Adjustment feet Rear Bottom side Remote controlHow to disable the Laser button How to enable the Laser buttonBattery installation Remote controlOperation range of the remote control Reception angle verticalLayout of the projector InstallationRear projection Front projectionProjector + AV device Basic connectionsProjector + DVD player or Hdtv decoder VCR, etcCOMPUTER/COMPONENT Video DVI-D Hdcp IN-2 Projector + Computer Basic connectionsFor Macintosh About DDCAfter using the projector Adjustment of the projection anglePreparation Preparation for projectionBasic operation Power-onVolume from the speaker Power-offAnamorphic mode Auto Position buttonBasic operation Menu operationOff. Use the remote control to turn on the lamp Projector is in the stand-by mode when the lamp isStand-by mode when there is no signal input from SourceMenu operation Signal User No need to adjust in normal useImage adjustment Image adjustmentColor temperature About color temperatureImage adjustment Adjustment of the image from the computerSimple adjustment method Expand Advanced featuresPicture in Picture PinP StillSetting of the image displayed during startup or muting Advanced featuresInstallation other devices remote commands How to installHow to use the installed functions Projector + computer with USB connector Mouse remote controlOperation USBTo cancel the password function Password functionTo enable the password function FunctionInterval of lamp replacement Lamp replacementTroubleshooting Problem Cause and solutionImages arent projected on the screen Images arent projected correctly TroubleshootingCleaning of the projector and the ventilation slots Cleaning of the lensOthers Condition IndicatorsKensington Lock SpecificationsCD-ROM SpecificationsCGA70 Mitsubishi Electric Corporation