Mitsubishi Electronics LVP-X400U user manual Preparing the projector for operation

Page 12

Preparing the projector for operation

Getting ready for projection

1.Connect the power cord provided to the projector.

2.Connect the power cord to the wall power outlet.

3.Remove the lens cap.

Warning:

Do not look directly into the lens when projector is “ON”.

The lens cap is for protecting the lens. If you leave the power on with the cap on, the cap may be warped. Please remove the lens cap when you turn the power on.

This projector is equipped with the power cords for both U.S. and Europe. Use the appropriate power cord for your country.

A three-pin grounding type power plug is used with the projector. Do not remove the grounding pin on the power plug. If you are unable to insert the plug into the outlet, contact your electrician to replace your A/C outlet.

The supplied power cord for U.S. is used for 120V only. Never connect to any outlet or power supply having a different voltage or frequency. If you connect to the power supply having a different voltage, please use the appropriate power cord.

Use 100-240V AC 50/60Hz correct voltage other- wise it may lead to fire or electric shock.

Do not place any objects on the power cord, and keep the projector away from heat sources to avoid dam- aging the power cord. A damaged power cord can cause fire or electric shock.

Do not modify or alter the power cord otherwise it may cause fire or electric shock.

Contact your dealer if the cord is damaged.

Caution:

Plug in firmly and unplug by holding the plug, not by pulling the cable out.

Do not plug in or out with wet hands. It may cause an electric shock.

Adjusting the angle of projection

For the best result, project onto a flat screen with a 90 degree angle to the floor. If necessary, tilt the projector by adjusting two foot adjustments on the bottom of the projector.

screen

Adjustment foot

 

1.Lift the projector to the appropriate angle.

2.Press the buttons by the projector’s adjustable front feet, this will allow the feet to slide out to the ap- proximate position.

3.Release the foot adjustment buttons to lock the feet in that position.

4.Rotate the projector feet for fine adjustment.

After using the projector

5. Return the adjustable feet into the projector.

Important:

The image becomes trapezoid shape when the screen or project is not level. Use KEYSTONE button and + or - buttons on the remote control to adjust, however, the circumference of the image may not be focused.

Screen on a flat wall with a 90˚ angle to the floor.

Align projector to produce a full screen display as illustrated on page 9.

The distance from the projector to the screen must be compatible with screen size chart on page 9. Note the distance from the screen chart.

EN – 12

Image 12
Contents English Français Deutsch Italiano Español X400When using the projector in Europe Compliance NoticeContents Important safeguards It can lead to fire or electric shock It can lead to fireIf you use incorrect voltage, it can lead to fire Overview Terminal boardThis remote control is class 2 max. output 1 mW laser diode About laser beam640 660 nm laser equipment Beam Divergence 3m distance about 5.0mm x 3.0mm ±1.5mmUsing the remote control Battery installationOperation area for wireless control system Using the wired remote controlInstallation Orientation of the projectorScreen Basic connections Projector + AV equipmentProjector + DVD player or Hdtv decoder For using Macintosh Projector + Personal computerFor computer with DVI terminal About DDC For DVI connectionAdjusting the angle of projection Preparing the projector for operationGetting ready for projection To operate projector power on Auto PositionButton To operate projector power on Continue Volume from the speakerTurning off the projector AV muteMenu operation Basic operationInstallation Menu operationPicture OptionUser memory for signal setting SignalPicture adjustment Adjusting the imageColor temperature Color matrixAdjustment from personal computer Picture adjustment XGA85Advanced features for presentation ExpandPicture in Picture PinP StillAdvanced features for presentation Mouse remote controlProjector + computer with USB connector Projector + computer with PS/2 connectorLamp replacement Interval of the lamp replacementHow to reset the operation time meter Maintenance Cleaning the air-filterCleaning the projector and the ventilation slots Cleaning the lensTroubleshooting Indicators Normal conditionAbnormal condition Specifications Specifications ConnectorsDimensional drawings mm Replacement part Option / Not included in the box871D293A40 Control projector by using a personal computer Control command diagramInterface Operation commands Computer input commandsHow to set the grade Control sequenceVolume commands Remote commandsExample Display Menu selection bar. is for Ascii code Menu setting commands Example 1 Set the Auto Power on to onReading command diagram
Related manuals
Manual 29 pages 61.34 Kb