Mitsubishi Electronics LVP-X400U user manual When using the projector in Europe, Compliance Notice

Page 2

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the litera- ture accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

NOTE:

SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET MUST BE IN- STALLED NEAR THE EQUIPMENT AND SHOULD BE EASILY ACCESSIBLE.

WARNING

Use the attached specified power supply cord. If you use another power-supply cord, it may cause interfer- ence with radio and television reception.

Use the attached RGB cable, RS-232C cable with this equipment so as to keep interference within the limit of a FCC Class A device.

This apparatus must be grounded.

The projector automatically shuts off when the lamp is used up in about 1,500 hours and cannot be used until the lamp is replaced and the internal timer is reset. See page 23.

DO NOT LOOK DIRECTLY INTO THE LENS WHEN PROJECTOR IS IN THE POWER ON MODE.

When using the projector in Europe

COMPLIANCE NOTICE

This LCD - Video Projector complies with the requirements of the EC Directive 89/336/EEC “EMC Directive” as amended by Directive 93/68/EEC and 73/23/EEC “Low Voltage Directive” as amended by Directive 93/68/EEC.

The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterised by their connection to the public low voltage power supply system.

WARNING

Use the attached RGB cable or RS-232C cable with this equipment so as to keep interference within the limits of a EN55022 Class B and EN55013. Please follow WARNINGS instructions.

EN – 2

Image 2
Contents English Français Deutsch Italiano Español X400When using the projector in Europe Compliance NoticeContents Important safeguards If you use incorrect voltage, it can lead to fire It can lead to fire or electric shockIt can lead to fire Overview Terminal board640 660 nm laser equipment This remote control is class 2 max. output 1 mW laser diodeAbout laser beam Beam Divergence 3m distance about 5.0mm x 3.0mm ±1.5mmOperation area for wireless control system Using the remote controlBattery installation Using the wired remote controlScreen InstallationOrientation of the projector Projector + DVD player or Hdtv decoder Basic connectionsProjector + AV equipment For computer with DVI terminal For using MacintoshProjector + Personal computer About DDC For DVI connectionGetting ready for projection Adjusting the angle of projectionPreparing the projector for operation Button To operate projector power onAuto Position Turning off the projector To operate projector power on ContinueVolume from the speaker AV muteMenu operation Basic operationPicture InstallationMenu operation OptionUser memory for signal setting SignalColor temperature Picture adjustmentAdjusting the image Color matrixAdjustment from personal computer Picture adjustment XGA85Picture in Picture PinP Advanced features for presentationExpand StillProjector + computer with USB connector Advanced features for presentationMouse remote control Projector + computer with PS/2 connectorHow to reset the operation time meter Lamp replacementInterval of the lamp replacement Cleaning the projector and the ventilation slots MaintenanceCleaning the air-filter Cleaning the lensTroubleshooting Abnormal condition IndicatorsNormal condition Specifications Dimensional drawings mm SpecificationsConnectors Replacement part Option / Not included in the box871D293A40 Interface Control projector by using a personal computerControl command diagram How to set the grade Operation commandsComputer input commands Control sequenceExample Display Menu selection bar. is for Ascii code Volume commandsRemote commands Menu setting commands Example 1 Set the Auto Power on to onReading command diagram
Related manuals
Manual 29 pages 61.34 Kb