Mitsubishi Electronics LVP-X400U user manual Installation, Orientation of the projector, Screen

Page 9

Installation

Orientation of the projector

Picture size can be set by changing the distance between the screen and the projector.

Front projection

Screen

Width

AB

To find the approximate distance between the projector and screen: Multiply the width of the screen

ENGLISH

Height

Screen

A=B

L (between the screen and the head of the projector)

x 1.9 (min.) , Multiply the width of the screen x 2.4 (max.).

Refer to the chart for recom- mended distances in maximum zoom and minimum zoom.

 

Screen

 

Distance from screen (L) / (approximate)

 

 

 

Maximum

Minimum

Diagonal size

Height

Width

zoom (min.)

zoom (max.)

(inch)

(inch)

(inch)

(cm)

(inch)

(cm)

(inch)

 

 

 

 

 

 

 

40 "

24 "

32 "

155

61 "

195

77 "

60 "

36 "

48 "

235

92 "

296

116 "

80 "

48 "

64 "

315

124 "

396

156 "

100 "

60 "

80 "

394

155 "

496

195 "

120 "

72 "

96 "

474

187 "

597

235 "

140 "

84 "

112 "

554

218 "

697

274 "

160 "

96 "

128 "

634

250 "

797

314 "

180"

108 "

144 "

714

281 "

898

353 "

200 "

120 "

160 "

794

312 "

998

393 "

300 "

180 "

240 "

1194

470 "

The above numbers are approximate, and may be slightly different from the actual measurements.

Front projection, ceiling mount

For ceiling mount, you need the ceiling mount kit. Ask a specialist for installation. For more details, consult your dealer.

SCREEN

When using the ceiling mount, set IMAGE RE- VERSE in the INSTALLATION menu to MIR- ROR INVERT. See Page 16.

Projected images may appear darker when the unit is used as a ceiling installation than when it is used in the tabletop position. This does not signify a product malfunction.

Rear projection

Ask a specialist for installation. For more details, consult your dealer.

SCREEN

For rear projection, set IMAGE REVERSE in the INSTALLATION menu to MIRROR. See Page 16.

Caution:

Placing the projector on a carpet reduces ventila- tion from the fan at the bottom and might cause problems. Place a hard board or similar item under the projector to facilitate ventilation of the unit.

Place the projector more than 20 in. from the wall to prevent blocking the intake, exhaust slots and ventilation of this projector because hot air comes out of it.

Do not use the projector under the following circumstances, which may cause fire or electric shock.

in a dusty or humid place

while the projector is lying sideways or upside down

near a heater

in a kitchen or oily, smoky or damp place

in direct sunlight

with high temperature, such as a closed car

where the temperature is lower than 41° F or higher than 104° F

Important:

Do not put stress on the lens, as this may cause damage.

´

EN – 9

Image 9
Contents X400 English Français Deutsch Italiano EspañolCompliance Notice When using the projector in EuropeContents Important safeguards It can lead to fire or electric shock It can lead to fireIf you use incorrect voltage, it can lead to fire Terminal board OverviewAbout laser beam This remote control is class 2 max. output 1 mW laser diode640 660 nm laser equipment Beam Divergence 3m distance about 5.0mm x 3.0mm ±1.5mmBattery installation Using the remote controlOperation area for wireless control system Using the wired remote controlInstallation Orientation of the projectorScreen Basic connections Projector + AV equipmentProjector + DVD player or Hdtv decoder Projector + Personal computer For using MacintoshFor computer with DVI terminal About DDC For DVI connectionAdjusting the angle of projection Preparing the projector for operationGetting ready for projection To operate projector power on Auto PositionButton Volume from the speaker To operate projector power on ContinueTurning off the projector AV muteBasic operation Menu operationMenu operation InstallationPicture OptionSignal User memory for signal settingAdjusting the image Picture adjustmentColor temperature Color matrixAdjustment from personal computer XGA85 Picture adjustmentExpand Advanced features for presentationPicture in Picture PinP StillMouse remote control Advanced features for presentationProjector + computer with USB connector Projector + computer with PS/2 connectorLamp replacement Interval of the lamp replacementHow to reset the operation time meter Cleaning the air-filter MaintenanceCleaning the projector and the ventilation slots Cleaning the lensTroubleshooting Indicators Normal conditionAbnormal condition Specifications Connectors SpecificationsDimensional drawings mm Replacement part Option / Not included in the box871D293A40 Control projector by using a personal computer Control command diagramInterface Computer input commands Operation commandsHow to set the grade Control sequenceVolume commands Remote commandsExample Display Menu selection bar. is for Ascii code Example 1 Set the Auto Power on to on Menu setting commandsReading command diagram
Related manuals
Manual 29 pages 61.34 Kb