Mitsubishi Electronics LVP-X400U user manual User memory for signal setting, Signal

Page 17
HOLD
USER MEMORIZE
MEMORY CALL HORIZ. POSITION VERT. POSITION FINE SYNC. TRACKING COMPUTER INPUT

4 SIGNAL

 

MEMORY CALL

Use to select AUTO, USER 1 or USER 2. See below.

HORIZ. POSITION ....

Use to adjust the horizontal position of the image.

VERT. POSITION

Use to adjust the vertical position of the image.

FINE SYNC

Use to synchronize the projector with PC input signals so

 

that the image is not blurred.

TRACKING

Use to avoid image noise such as wide stripes.

COMPUTER INPUT ....

The unit adjusts itself automatically when connected to a

 

DVD player with a component video output (Y, CB, CR). In

 

the case ( Y, PB, PR). In the case the projector is connected to

 

equipment that includes RGB output terminal, adjust to

 

RGB mode.

HOLD

Adjusts the image when flagging occurs near the top of the

 

screen.

SIGNAL

A

U

RR GG BB

Opt

XGA60

AUTO

0

0

0

0

RGB

AUTO

DELETE DEFAULT

ENGLISH

5 SIGNAL - USER (Normally, there is no need for adjustments.)

 

 

CLAMP POSITION/

 

 

 

CLAMP WIDTH

If you use something similar, the brighter colors of the

SIGNAL-USER

 

 

projected image may become blurred. In this case, adjust

CLAMP POSITION

0

 

CLAMP POSITION or CLAMP WIDTH.

CLAMP WIDTH

0

HORIZ.PIXELS ..

Use to adjust the width of the image. The image size grows

HORIZ. PIXELS

0

 

wider as the number increases. (Adjust to the horizontal

VERT. LINES

0

 

pixels of the input signal for normal setting.)

PLL

AUTO

VERT.LINES

Use to adjust the height of the image. The image size grows

VERT. SYNC.

AUTO

 

higher as the number increases. (Adjust to the vertical lines

SHUTTER(U)

0

 

of the input signal for normal setting.)

SHUTTER(L)

0

PLL

Use to adjust the image when skewed on top. Select AUTO for

SHUTTER(LS)

0

 

normal setting.

SHUTTER(RS)

0

VERT.SYNC

Use to adjust the image when its motion does not run

 

 

 

smoothly. Select AUTO for normal setting.

 

 

SHUTTER(U)

Use to adjust the image when the noise etc. appears on top part of image.

 

SHUTTER(L)

Use to adjust the image when the noise etc. appears on bottom part of image.

 

SHUTTER(LS) ....

Use to adjust the image when the noise etc. appears on left side of image.

 

SHUTTER(RS) ...

Use to adjust the image when the noise etc. appears on right side of image.

 

User memory for signal setting

This projector can memorize the maximum of 2 signal menu settings.

Memorizing the setting

1.Select MEMORIZE in the SIGNAL menu, and press the ENTER button.

2.Press the $ or % button to select the memory which you wish to record (USER 1 or USER 2).

3.Press the ENTER button.

Initialite the setting which has been changed (Default)

Select RESET in the SIGNAL menu, and press the ENTER button.

When initializing, selection buttons will not work for about 2 - 18 seconds.

Select the user setting

Select MEMORY CALL in SIGNAL menu, and press the $ or % button to select the memory (USER 1 or USER 2).

Reset the recorded setting

1.Select DELETE in the SIGNAL menu, and press the ENTER button.

2.Press the $ or % button to select the memory which you wish to reset (USER 1 or USER 2).

3.Press the ENTER button.

The recorded setting will be reset.

EN – 17

Image 17
Contents X400 English Français Deutsch Italiano EspañolCompliance Notice When using the projector in EuropeContents Important safeguards If you use incorrect voltage, it can lead to fire It can lead to fire or electric shockIt can lead to fire Terminal board OverviewAbout laser beam This remote control is class 2 max. output 1 mW laser diode640 660 nm laser equipment Beam Divergence 3m distance about 5.0mm x 3.0mm ±1.5mmBattery installation Using the remote controlOperation area for wireless control system Using the wired remote controlScreen InstallationOrientation of the projector Projector + DVD player or Hdtv decoder Basic connectionsProjector + AV equipment Projector + Personal computer For using MacintoshFor computer with DVI terminal About DDC For DVI connectionGetting ready for projection Adjusting the angle of projectionPreparing the projector for operation Button To operate projector power onAuto Position Volume from the speaker To operate projector power on ContinueTurning off the projector AV muteBasic operation Menu operationMenu operation InstallationPicture OptionSignal User memory for signal settingAdjusting the image Picture adjustmentColor temperature Color matrixAdjustment from personal computer XGA85 Picture adjustmentExpand Advanced features for presentationPicture in Picture PinP StillMouse remote control Advanced features for presentationProjector + computer with USB connector Projector + computer with PS/2 connectorHow to reset the operation time meter Lamp replacementInterval of the lamp replacement Cleaning the air-filter MaintenanceCleaning the projector and the ventilation slots Cleaning the lensTroubleshooting Abnormal condition IndicatorsNormal condition Specifications Connectors SpecificationsDimensional drawings mm Replacement part Option / Not included in the box871D293A40 Interface Control projector by using a personal computerControl command diagram Computer input commands Operation commandsHow to set the grade Control sequenceExample Display Menu selection bar. is for Ascii code Volume commandsRemote commands Example 1 Set the Auto Power on to on Menu setting commandsReading command diagram
Related manuals
Manual 29 pages 61.34 Kb