Mitsubishi Electronics LVP-X400U user manual Using the remote control, Battery installation

Page 8

Using the remote control

Battery installation

Use two AA size batteries.

1.Remove the back cover of the remote control by pushing the battery compartment door in the direction of the arrow.

2.Load the batteries making sure that they are positioned correctly (+ to +, and - to -).

3.Replace the back cover.

1

2

3

Important:

Do not use a new battery with an old one.

Load batteries in the correct position.

Do not heat, take apart, or throw batteries into fire.

Do not try to recharge batteries. Do not use rechargeable batteries.

If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in contact with your eyes, rinse them with water and then consult your doctor.

Operation area (for wireless control system)

The range for operation is about 10 m (about 32 feet) when the remote control points to the projector. The dis- tance to the screen back to the projector must be less than 7 m (about 23 feet). Depending on the type of the screen, the distance will be different.

20˚

20˚

15˚

15˚

30˚

30˚

20˚

20˚

Important:

Avoid the direct sunlight or fluorescent light to the remote control sensor. Also keep the distance of more than 2 m (6.5") between the remote control sensor and fluorescent lamp on the remote control may not work correctly.

Using the wired remote control

Attached remote control for this projector can be used as a wired remote control with remote control cable. Wired remote control is useful for operating in a distance or outside of the operating area.

 

 

COMPUTER 1 IN

 

RS-232C

USB

 

INPUT SELECT

 

 

REMOTE

 

AUDIO 1 IN

VIDEO 1

VIDEO 2

 

DIGITAL

 

 

IN

IN

 

ANALOG

 

 

 

 

MAIN

COMPUTER 2 IN

AUDIO 2 IN

S-VIDEO

 

VIDEO

 

O

I

 

 

 

 

 

AC IN

COMPUTER OUT

AUDIO OUT

L

 

 

 

 

AUDIO

R

When the remote control is connected with remote control cable, it does not work as a wireless remote control.

When you need a longer cable, use a pin-pin cable.

When using the wired remote control, the laser beam may be darker. It is normal.

EN – 8

Image 8
Contents English Français Deutsch Italiano Español X400When using the projector in Europe Compliance NoticeContents Important safeguards If you use incorrect voltage, it can lead to fire It can lead to fire or electric shockIt can lead to fire Overview Terminal boardThis remote control is class 2 max. output 1 mW laser diode About laser beam640 660 nm laser equipment Beam Divergence 3m distance about 5.0mm x 3.0mm ±1.5mmUsing the remote control Battery installationOperation area for wireless control system Using the wired remote controlScreen InstallationOrientation of the projector Projector + DVD player or Hdtv decoder Basic connectionsProjector + AV equipment For using Macintosh Projector + Personal computerFor computer with DVI terminal About DDC For DVI connectionGetting ready for projection Adjusting the angle of projectionPreparing the projector for operation Button To operate projector power onAuto Position To operate projector power on Continue Volume from the speakerTurning off the projector AV muteMenu operation Basic operationInstallation Menu operationPicture OptionUser memory for signal setting SignalPicture adjustment Adjusting the imageColor temperature Color matrixAdjustment from personal computer Picture adjustment XGA85Advanced features for presentation ExpandPicture in Picture PinP StillAdvanced features for presentation Mouse remote controlProjector + computer with USB connector Projector + computer with PS/2 connectorHow to reset the operation time meter Lamp replacementInterval of the lamp replacement Maintenance Cleaning the air-filterCleaning the projector and the ventilation slots Cleaning the lensTroubleshooting Abnormal condition IndicatorsNormal condition Specifications Specifications ConnectorsDimensional drawings mm Replacement part Option / Not included in the box871D293A40 Interface Control projector by using a personal computerControl command diagram Operation commands Computer input commandsHow to set the grade Control sequenceExample Display Menu selection bar. is for Ascii code Volume commandsRemote commands Menu setting commands Example 1 Set the Auto Power on to onReading command diagram
Related manuals
Manual 29 pages 61.34 Kb