Mitsubishi Electronics FL7000 user manual Front projection, ceiling mounting, Rear projection

Page 12

Setting up your projector (continued)

Front projection, ceiling mounting

For ceiling mounting, you need the ceiling mount kit designed for this projector. Ask a specialist for installa- tion. For details, consult your dealer.

•The warranty on this projector does not cover any damage caused by use of any non-recommended ceiling mount kit or installation of the ceiling mount kit in an improper location.

•When using the projector mounted on the ceiling, set IMAGE REVERSE in the INSTALLATION menu to MIRROR INVERT. See page 24.

•When the projector is mounted on the ceiling, im- ages may appear darker than those projected in the case of tabletop mounting. This isn’t a product malfunction.

•Ask your installation specialist to provide a breaker. When you do not use the projector, be sure to shut down the main power by the breaker.

•Do not install the projector where the exhaust vents are exposed to air emitted by an air conditioning. Such installation may cause a breakdown.

•Do not install the projector near a fire alarm because it emits hot air from its exhaust vents.

Rear projection

Ask a specialist for installation. For details, consult your dealer.

•For rear projection, set IMAGE REVERSE in the IN- STALLATION menu to MIRROR. See page 24.

Caution:

•Placing the projector directly on a carpet impairs ventilation by the fans, causing damage or failure. Put a hard board under the projector to facilitate ventilation.

•Place the projector at least 50 cm (or 20 inches) away from the wall to prevent the air inlet grille and the air outlet grilles that emit hot air from being blocked.

•Do not use the projector in the following locations and manners, which may cause fire or electric shock.

•In a dusty or humid place.

•In a sideways position, or with the lens facing down.

•Near a heater.

•In an oily, smoky, or damp place such as a kitchen.

•In direct sunlight.

•Where the temperature rises high, such as in a closed car.

•Where the temperature is lower than +41ºF (or +5ºC) or higher than +104ºF (or +40ºC ).

Important:

•We don’t recommend using the projector at an alti- tude of 1500 meters or higher. Use at an altitude of 1500 meters or higher may affect the projector’s life.

EN-12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents
FL7000 When using the projector in Europe Compliance NoticeContents Important safeguards Important safeguards Checking accessories Inserting the batteries into the remote controlPreparing your projector Preparating your projector OverviewControl area Terminal board Bottom side Remote control Adjustment feet Air inlet grille/Filter cover Lamp cover How to disable the Laser button How to enable the Laser buttonUsing the remote control Operational range of the remote controlUsing the wired remote control Reception angleSetting up your projector Setting up the screenWhen the aspect ratio of the screen is Screen size and projection distanceSetting up your projector Adjusting the projection angleWhen fine streaks are seen on projected images When projected images are distorted to a trapezoidFront projection, ceiling mounting Rear projectionConnecting the projector to a computer Viewing computer imagesPlugging the power cord Viewing computer imagesFor monitor connection For audio output connectionProjecting images Remove the lens capWhen connecting to a notebook computer Example of the setting procedure for external outputTo stop projecting AV muteConnecting the projector to video equipment Connecting to a video player, etcViewing video images Viewing video images Projector + DVD player or Hdtv decoderConnection for video equipment having an Hdmi terminal Plugging in the power cord Connection for video equipment having a DVI-D terminalEN-20 Volume from the speaker Setting the aspect ratioHow to change the settings With the remote control With the Feature menuSetup Menu operationHow to set the menus Available settings in the menusMenu operation Image menu Image Advanced menuInstallation menu LOWFeature menu Aspect AutoSignal menu Signal User menuInformation menu InformationAdjusting projected images To adjust the brightness Contrast and BrightnessTo adjust the color Color and Tint To sharpen or soften the projected image SharpnessAdjusting projected images To adjust the tone of white Color TempAbout color temperature Color EnhancerHow to adjust the computer image YESSimple method to adjust the image position To adjust the horizontal positionTo adjust the vertical position LPF Progressive filterAdvanced features Setting procedureSet the background color Set the image sizeAdvanced features Password functionTo cancel the password function To enable the password functionTo use the split mode SplitFreeze To resume the motion in the imageMouse remote control Projector + computer with USB connectorOperation Up buttonSupervising and controlling by computer ProjectorViewPJLink About PJLinkIndicators Normal conditionTerminal cover with anti-theft alarm device Procedure for setting the anti-theft alarm deviceProcedure for changing batteries Interval of lamp replacement Replacing the lampReset of the lamp operation time Replacing the lampTo replace the lamp Maintenance Cleaning of the air-filterCleaning of the projector and the ventilation slots Cleaning of the lensTroubleshooting No image appears on the screenTroubleshooting No image appears on the screen Problem SolutionImages are not displayed correctly Problem Solution Others Problem Solution Kensington LockReplacement part option/not included in the box SpecificationsSpecifications XGA85Connectors Dimension drawings unit mmReal mode Without terminal cover With terminal coverMitsubishi Projector Contact Information
Top Page Image Contents