Mitsubishi Electronics FL7000 user manual EN-20

Page 20

Viewing video images (continued)

C. Projecting images

Preparation:

• Remove the lens cap.

 

POWER button

COMPUTER 1, 2 buttons

 

 

POWER button

 

 

VIDEO button

 

 

DVI-D(HDCP) button

S-VIDEO button

 

 

 

 

 

VIDEO button

 

COMPUTER button

 

 

 

ZOOM/FOCUS button

LENS SHIFT button

 

 

ZOOM/FOCUS button

 

Main power switch

LENS SHIFT button

 

1.Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red.

•If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the POWER button may not work after the main power switch is turned ON. (The STATUS indicator blinks green.) After the fan stops rotating, press the POWER button to turn back on the POWER indicator.

2.Turn on the power of the connected video equipment.

3.Press the POWER button.

•It may take about 1 minute for the lamp to light up.

•The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.

•Do not cover the lens with the lens cap while the lamp is on.

•After the POWER button is pressed, the image may flicker before the lamp becomes stable. This is not a product malfunction.

•Regardless of the setting of LAMP MODE in the INSTALLATION menu, the STANDARD lamp mode is activated by default whenever the projector is turned on. When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to LOW about 1 minute after turn-on.

•The projector starts warming up when the POWER button is pressed. During the warm-up process, images may appear dark and no commands are accepted.

•By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when the STATUS indicator blinks red. (See page 37.)

•After the POWER button is pressed, a white bar may appear on the right edge of the screen for about 1 second, but this is not a malfunction.

4.Press the ZOOM/FOCUS button to display “FOCUS”.

5.Adjust with the W or X button to get a fine picture.

•When the ENTER button is pressed while “FOCUS” is displayed, the adjustment mode is switched between FAST and STEP. When FAST is selected, the speed of focus controlled by the W or X button becomes fast, and it becomes slow when STEP is selected.

6.Select an input source.

•Press the VIDEO button on the projector or the VIDEO or S-VIDEO button on the remote control that is corresponding to the terminal in use.

•The input source is switched between VIDEO and S-VIDEO at every press of the VIDEO button on the projector.

•You cannot change the input source while the menu is being displayed.

•Though it may take some time before an image is displayed on the screen depending on the type of the input signal, such symptom is not a malfunction.

•Some images become easier to view when the setting of aspect ratio is changed. (See page 21.)

•When projecting images from a DVD player that is connected to the COMPUTER/COMPONENT VIDEO DVI-D (HDCP) terminal, press the COMPUTER button on the projector to select DVI or press the DVI-D (HDCP) button on the remote control.

•When projecting images from a DVD player that is connected to the COMPUTER/COMPONENT VIDEO IN 1 or COMPUTER/COMPONENT VIDEO IN 2 terminal, press the COMPUTER button on the projector or the COMPUTER 1 or COMPUTER 2 button on the remote control.

•When COMPUTER 1 or COMPUTER 2 is chosen as the source, images supplied from the computer may flicker. Press the W or X button on the remote control to reduce flicker, if it occurs.

•When an image supplied from a video device to the COMPUTER1, COMPUTER2 or DVI input source is displaced, select VIDEO SIGNAL adjustment mode as described in “AUTO POSITION button” on page 16.

7.Adjust the position of the projector to keep an appropriate projection distance with which images are projected in their specified sizes.

8.Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 10.)

•When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 11.)

9.Press the ZOOM/FOCUS button to display “FOCUS” and then press the button again to display “ZOOM.”

10.Adjust with the W or X button to get an approximate size.

•When the ENTER button is pressed while “ZOOM” is displayed, the adjustment mode is switched between FAST and STEP. When FAST is selected, the speed of zoom controlled by the W or X button becomes fast, and it becomes slow when STEP is selected.

11.Press the LENS SHIFT button. The LENS SHIFT menu appears at the center of the screen.

12.Press the S or T button to adjust the vertical position and W or X button to adjust the horizontal position of the displayed image.

•When the image is not displayed within the screen, adjust the projection angle. In addition, perform the keystone adjustment, if necessary. (See page 11.)

Repeat steps 4, 5 and 9 to 12, if necessary.

EN-20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents FL7000 When using the projector in Europe Compliance NoticeContents Important safeguards Important safeguards Preparing your projector Checking accessoriesInserting the batteries into the remote control Control area Terminal board Preparating your projectorOverview Bottom side Remote control Adjustment feet Air inlet grille/Filter cover Lamp coverHow to disable the Laser button How to enable the Laser buttonUsing the remote control Operational range of the remote controlUsing the wired remote control Reception angleSetting up your projector Setting up the screenWhen the aspect ratio of the screen is Screen size and projection distanceSetting up your projector Adjusting the projection angleWhen fine streaks are seen on projected images When projected images are distorted to a trapezoidFront projection, ceiling mounting Rear projectionConnecting the projector to a computer Viewing computer imagesPlugging the power cord Viewing computer imagesFor monitor connection For audio output connectionProjecting images Remove the lens capWhen connecting to a notebook computer Example of the setting procedure for external outputTo stop projecting AV muteViewing video images Connecting the projector to video equipmentConnecting to a video player, etc Connection for video equipment having an Hdmi terminal Viewing video imagesProjector + DVD player or Hdtv decoder Plugging in the power cord Connection for video equipment having a DVI-D terminalEN-20 Volume from the speaker Setting the aspect ratioHow to change the settings With the remote control With the Feature menuSetup Menu operationHow to set the menus Available settings in the menusMenu operation Image menu Image Advanced menuInstallation menu LOWFeature menu Aspect AutoSignal menu Signal User menuInformation menu InformationAdjusting projected images To adjust the brightness Contrast and BrightnessTo adjust the color Color and Tint To sharpen or soften the projected image SharpnessAdjusting projected images To adjust the tone of white Color TempAbout color temperature Color EnhancerHow to adjust the computer image YESSimple method to adjust the image position To adjust the horizontal positionTo adjust the vertical position LPF Progressive filterAdvanced features Setting procedureSet the background color Set the image sizeAdvanced features Password functionTo cancel the password function To enable the password functionTo use the split mode SplitFreeze To resume the motion in the imageMouse remote control Projector + computer with USB connectorOperation Up buttonSupervising and controlling by computer ProjectorViewPJLink About PJLinkIndicators Normal conditionProcedure for changing batteries Terminal cover with anti-theft alarm deviceProcedure for setting the anti-theft alarm device Interval of lamp replacement Replacing the lampTo replace the lamp Reset of the lamp operation timeReplacing the lamp Maintenance Cleaning of the air-filterCleaning of the projector and the ventilation slots Cleaning of the lensTroubleshooting No image appears on the screenImages are not displayed correctly Problem Solution TroubleshootingNo image appears on the screen Problem Solution Others Problem Solution Kensington LockReplacement part option/not included in the box SpecificationsSpecifications XGA85Connectors Dimension drawings unit mmReal mode Without terminal cover With terminal coverMitsubishi Projector Contact Information

FL7000 specifications

Mitsubishi Electronics has once again showcased its commitment to innovation with the launch of the FL7000 series, a cutting-edge display technology aimed at enhancing visual experiences across various sectors including retail, corporate, and entertainment. The FL7000 series is engineered to deliver stunning image quality, versatility, and advanced features that facilitate seamless integration and usability.

One of the standout characteristics of the FL7000 series is its impressive resolution. With 4K Ultra HD capabilities, it provides crystal-clear images with rich detail, making it an ideal choice for presentations, advertisements, and visual displays. The high brightness levels ensure that images remain vibrant even in well-lit environments, which is crucial for retail and public spaces.

The FL7000 series includes advanced image processing technologies that enhance color accuracy and contrast. With a wide color gamut, it can reproduce a broader spectrum of colors, allowing images to appear more lifelike. The incorporation of HDR (High Dynamic Range) technology further elevates the viewing experience by providing deeper blacks and brighter whites, which is essential for dynamic visual content.

Flexibility and ease of use are other key features of the FL7000 series. The displays are designed for easy installation and integration into existing setups, whether as part of a corporate conference room, a digital signage solution, or a creative installation. The modular design allows for configurations that can adapt to various space constraints and customer needs.

Mitsubishi also emphasizes connectivity in the FL7000 series. The displays come equipped with multiple input options, including HDMI, DisplayPort, and USB interfaces, enabling compatibility with a wide range of media sources. This versatility empowers users to easily switch between different content, making it suitable for dynamic environments.

Additionally, the FL7000 series features an intuitive user interface that simplifies operation and management. Users can configure settings, schedule content, and even manage multiple displays through an integrated software solution, streamlining workflows and enhancing productivity.

In conclusion, the Mitsubishi Electronics FL7000 series sets a new benchmark for display technology, combining high-resolution imaging, advanced processing capabilities, and flexible installation options. Whether used for business, educational purposes, or retail applications, the FL7000 series is poised to transform the way visual information is presented and consumed. With its robust features and technological advancements, it represents a significant advancement in the realm of display solutions.
Top Page Image Contents