Mitsubishi Electronics FL7000 user manual Volume from the speaker, Setting the aspect ratio

Page 21

Viewing video images (continued)

Important:

• Focus, zoom and lens shift adjustment is possible in the normal picture mode only.

To stop projecting:

13.Press the POWER button.

•A confirmation message is displayed.

•To cancel the procedure, leave the projector for a while or press any button except the POWER button. 14.Press the POWER button again.

•The lamp goes out and the projector goes into a standby mode. In this standby mode, the STATUS indicator

blinks green.

15.Wait about 2 minutes for the STATUS indicator to be turned off.

•During this period of 2 minutes in the standby mode, the intake fan and exhaust fan rotate to cool the lamp.

•The air outlet fans rotate faster as the temperature around the projector rises.

•Do not turn off the main power switch or unplug the power cord while the STATUS indicator is blinking. Turning off the main power switch or unplugging the power cord immediately after use may cause a breakdown.

•Though the fans make loud sounds during cooling, such symptom is not a malfunction.

16.Turn off the main power switch.

•The POWER indicator will go out.

•If the main power switch should be turned off or the power cord should be unplugged accidentally while either the air inlet fan or the air outlet fans are operating or the lamp is on, allow the projector to cool down for 10 minutes with the power off. To light the lamp again, press the POWER button. If the lamp doesn’t light up im- mediately, repeat pressing the POWER button 2 or 3 times. If it should still fail to light up, replace the lamp.

•Cover the lens with the lens cap to protect it from dust.

•For safety’s sake, unplug the power cord from the outlet.

•When you repeat turning off the main switch within 30 minutes from the lamp illumination, an error may occur in the clock function of this product.

Volume from the speaker

Press the VOLUME + or - button to change the volume from the speakers.

The volume control bar will appear on the screen.

VOLUME 15

•The volume control bar will disappear about 10 seconds after the VOLUME button is released.

•The VOLUME buttons don’t function while the menu selection bar or the menu is being displayed.

•When a high-level audio signal, such as a DVD audio signal, is supplied to the AUDIO IN terminals, the output from the speakers may be distorted.

•When the audio cable is connected to the AUDIO OUT terminal, the speaker output is muted.

•The volume of the audio from the AUDIO OUT terminal is also changed by pressing the VOLUME buttons.

•The volume of the audio from the AUDIO OUT terminal varies within the range between 0 and 32.

Setting the aspect ratio

You can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Change the setting according to the type of the input video signal.

How to change the settings:

With the remote control:

1.Press the ASPECT button.

•Every time the ASPECT button is pressed, the aspect mode changes from AUTO to 16:9 (FULL), to REAL, and back to AUTO.

With the FEATURE menu:

 

 

 

 

opt.

 

 

 

 

 

 

 

(See page 23 for menu setting.)

 

 

 

 

 

 

 

 

 

 

 

 

FEATURE

 

1.

Display the FEATURE menu.

 

 

 

 

 

 

 

 

 

 

 

 

 

2.

Select ASPECT by pressing the S or T button.

 

 

ASPECT

 

AUTO

 

 

 

 

 

 

 

 

 

 

 

 

3.

Select your desired aspect ratio by pressing the W or X button.

 

 

 

 

 

 

 

 

 

 

 

 

To cancel the menu:

4. Press the MENU button.

Important:

•When a 4:3 image is kept displayed for a long time before displaying 16:9 image, the afterimages of the black bars may appear on the 16:9 image screen. (See page 43.)

EN-21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents FL7000 Compliance Notice When using the projector in EuropeContents Important safeguards Important safeguards Checking accessories Inserting the batteries into the remote controlPreparing your projector Preparating your projector OverviewControl area Terminal board Adjustment feet Air inlet grille/Filter cover Lamp cover Bottom side Remote controlHow to disable the Laser button How to enable the Laser buttonOperational range of the remote control Using the remote controlUsing the wired remote control Reception angleSetting up the screen Setting up your projectorWhen the aspect ratio of the screen is Screen size and projection distanceAdjusting the projection angle Setting up your projectorWhen fine streaks are seen on projected images When projected images are distorted to a trapezoidRear projection Front projection, ceiling mountingViewing computer images Connecting the projector to a computerViewing computer images Plugging the power cordFor monitor connection For audio output connectionRemove the lens cap Projecting imagesExample of the setting procedure for external output When connecting to a notebook computerTo stop projecting AV muteConnecting the projector to video equipment Connecting to a video player, etcViewing video images Viewing video images Projector + DVD player or Hdtv decoderConnection for video equipment having an Hdmi terminal Connection for video equipment having a DVI-D terminal Plugging in the power cordEN-20 Setting the aspect ratio Volume from the speakerHow to change the settings With the remote control With the Feature menuMenu operation SetupAvailable settings in the menus How to set the menusMenu operation Image menu Image Advanced menuLOW Installation menuAspect Auto Feature menuSignal User menu Signal menuInformation Information menuTo adjust the brightness Contrast and Brightness Adjusting projected imagesTo adjust the color Color and Tint To sharpen or soften the projected image SharpnessTo adjust the tone of white Color Temp Adjusting projected imagesAbout color temperature Color EnhancerYES How to adjust the computer imageTo adjust the horizontal position Simple method to adjust the image positionTo adjust the vertical position LPF Progressive filterSetting procedure Advanced featuresSet the background color Set the image sizePassword function Advanced featuresTo cancel the password function To enable the password functionSplit To use the split modeFreeze To resume the motion in the imageProjector + computer with USB connector Mouse remote controlOperation Up buttonProjectorView Supervising and controlling by computerPJLink About PJLinkNormal condition IndicatorsTerminal cover with anti-theft alarm device Procedure for setting the anti-theft alarm deviceProcedure for changing batteries Replacing the lamp Interval of lamp replacementReset of the lamp operation time Replacing the lampTo replace the lamp Cleaning of the air-filter MaintenanceCleaning of the projector and the ventilation slots Cleaning of the lensNo image appears on the screen TroubleshootingTroubleshooting No image appears on the screen Problem SolutionImages are not displayed correctly Problem Solution Kensington Lock Others Problem SolutionSpecifications Replacement part option/not included in the boxXGA85 SpecificationsDimension drawings unit mm ConnectorsReal mode Without terminal cover With terminal coverMitsubishi Projector Contact Information

FL7000 specifications

Mitsubishi Electronics has once again showcased its commitment to innovation with the launch of the FL7000 series, a cutting-edge display technology aimed at enhancing visual experiences across various sectors including retail, corporate, and entertainment. The FL7000 series is engineered to deliver stunning image quality, versatility, and advanced features that facilitate seamless integration and usability.

One of the standout characteristics of the FL7000 series is its impressive resolution. With 4K Ultra HD capabilities, it provides crystal-clear images with rich detail, making it an ideal choice for presentations, advertisements, and visual displays. The high brightness levels ensure that images remain vibrant even in well-lit environments, which is crucial for retail and public spaces.

The FL7000 series includes advanced image processing technologies that enhance color accuracy and contrast. With a wide color gamut, it can reproduce a broader spectrum of colors, allowing images to appear more lifelike. The incorporation of HDR (High Dynamic Range) technology further elevates the viewing experience by providing deeper blacks and brighter whites, which is essential for dynamic visual content.

Flexibility and ease of use are other key features of the FL7000 series. The displays are designed for easy installation and integration into existing setups, whether as part of a corporate conference room, a digital signage solution, or a creative installation. The modular design allows for configurations that can adapt to various space constraints and customer needs.

Mitsubishi also emphasizes connectivity in the FL7000 series. The displays come equipped with multiple input options, including HDMI, DisplayPort, and USB interfaces, enabling compatibility with a wide range of media sources. This versatility empowers users to easily switch between different content, making it suitable for dynamic environments.

Additionally, the FL7000 series features an intuitive user interface that simplifies operation and management. Users can configure settings, schedule content, and even manage multiple displays through an integrated software solution, streamlining workflows and enhancing productivity.

In conclusion, the Mitsubishi Electronics FL7000 series sets a new benchmark for display technology, combining high-resolution imaging, advanced processing capabilities, and flexible installation options. Whether used for business, educational purposes, or retail applications, the FL7000 series is poised to transform the way visual information is presented and consumed. With its robust features and technological advancements, it represents a significant advancement in the realm of display solutions.
Top Page Image Contents