Mitsubishi Electronics FL7000 user manual Projecting images, Remove the lens cap

Page 15

Viewing computer images (continued)

C. Projecting images

Preparation:

• Remove the lens cap.

COMPUTER 1, 2 buttons

 

POWER button

POWER button

 

 

 

 

DVI-D(HDCP) button

 

COMPUTER button

 

 

ZOOM/FOCUS button

LENS SHIFT button

 

ZOOM/FOCUS button

Main power switch

LENS SHIFT button

1.Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red.

•If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the POWER button may not work after the main power switch is turned ON. (The STATUS indicator blinks green.) After the fan stops rotating, press the POWER button to turn back on the POWER indicator.

2.Turn on the power of the connected computer.

3.Press the POWER button.

•It may take about 1 minute for the lamp to light up.

•The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.

•Do not cover the lens with the lens cap while the lamp is on.

•After the POWER button is pressed, the image may flicker before the lamp becomes stable. This is not a product malfunction.

•Regardless of the setting of LAMP MODE in the INSTALLATION menu, the STANDARD lamp mode is activated by default whenever the projector is turned on. When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to LOW about 1 minute after turn-on.

•The projector starts warming up when the POWER button is pressed. During the warm-up process, images may appear dark and no commands are accepted.

•By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when the STATUS indicator blinks red. (See page 37.)

•After the POWER button is pressed, a white bar may appear on the right edge of the screen for about 1 second, but this is not a malfunction.

4.Press the ZOOM/FOCUS button to display “FOCUS”.

5.Adjust with the W or X button to get a fine picture.

•When the ENTER button is pressed while “FOCUS” is displayed, the adjustment mode is switched between FAST and STEP. When FAST is selected, the speed of focus controlled by the W or X button becomes fast, and it becomes slow when STEP is selected.

6.Select an input source.

•Press the COMPUTER button on the projector or the COMPUTER 1, COMPUTER 2 or DVI-D(HDCP) button on the remote control that is corresponding to the terminal in use.

•The input source is switched from COMPUTER 1 to COMPUTER 2 to DVI at every press of the COMPUTER button on the projector.

•The projector automatically selects the appropriate signal format. The selected signal format is displayed on the screen.

•You cannot change the input source while the menu is being displayed.

•Though it may take some time before an image is displayed on the screen depending on the type of the input signal, such symptom is not a malfunction.

•Images may not be projected in the correct position, depending on the type of the input signal. In such a case, press the AUTO POSITION button. (See page 16.)

•When you display a computer signal having the same resolution as that of a signal from a video device (1080p, etc.) using the COMPUTER1, COMPUTER 2 or DVI input source, select AUTO ADJUST adjustment mode as de- scribed in “AUTO POSITION button” on page 16.

•When COMPUTER 1 or COMPUTER 2 is chosen as the source, images supplied from the computer may flicker. Press the W or X button on the remote control to reduce flicker, if it occurs.

7.Adjust the position of the projector to keep an appropriate projection distance with which images are projected in their specified sizes.

8.Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 10.)

•When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 11.)

9.Press the ZOOM/FOCUS button to display “FOCUS” and then press the button again to display “ZOOM.”

10.Adjust with the W or X button to get an approximate size.

•When the ENTER button is pressed while “ZOOM” is displayed, the adjustment mode is switched between FAST and STEP. When FAST is selected, the speed of zoom controlled by the W or X button becomes fast, and it becomes slow when STEP is selected.

11.Press the LENS SHIFT button. The LENS SHIFT menu appears at the center of the screen.

12.Press the S or T button to adjust the vertical position and W or X button to adjust the horizontal position of the displayed image.

•When the image is not displayed within the screen, adjust the projection angle. In addition, perform the keystone adjustment, if necessary. (See page 11.)

Repeat steps 4, 5 and 9 to 12, if necessary.

EN-15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents FL7000 Compliance Notice When using the projector in EuropeContents Important safeguards Important safeguards Checking accessories Inserting the batteries into the remote controlPreparing your projector Preparating your projector OverviewControl area Terminal board How to enable the Laser button Bottom side Remote controlAdjustment feet Air inlet grille/Filter cover Lamp cover How to disable the Laser buttonReception angle Using the remote controlOperational range of the remote control Using the wired remote controlScreen size and projection distance Setting up your projectorSetting up the screen When the aspect ratio of the screen isWhen projected images are distorted to a trapezoid Setting up your projectorAdjusting the projection angle When fine streaks are seen on projected imagesRear projection Front projection, ceiling mountingViewing computer images Connecting the projector to a computerFor audio output connection Plugging the power cordViewing computer images For monitor connectionRemove the lens cap Projecting imagesAV mute When connecting to a notebook computerExample of the setting procedure for external output To stop projectingConnecting the projector to video equipment Connecting to a video player, etcViewing video images Viewing video images Projector + DVD player or Hdtv decoderConnection for video equipment having an Hdmi terminal Connection for video equipment having a DVI-D terminal Plugging in the power cordEN-20 With the Feature menu Volume from the speakerSetting the aspect ratio How to change the settings With the remote controlMenu operation SetupImage menu Image Advanced menu How to set the menusAvailable settings in the menus Menu operationLOW Installation menuAspect Auto Feature menuSignal User menu Signal menuInformation Information menuTo sharpen or soften the projected image Sharpness Adjusting projected imagesTo adjust the brightness Contrast and Brightness To adjust the color Color and TintColor Enhancer Adjusting projected imagesTo adjust the tone of white Color Temp About color temperatureYES How to adjust the computer imageLPF Progressive filter Simple method to adjust the image positionTo adjust the horizontal position To adjust the vertical positionSet the image size Advanced featuresSetting procedure Set the background colorTo enable the password function Advanced featuresPassword function To cancel the password functionTo resume the motion in the image To use the split modeSplit FreezeUp button Mouse remote controlProjector + computer with USB connector OperationAbout PJLink Supervising and controlling by computerProjectorView PJLinkNormal condition IndicatorsTerminal cover with anti-theft alarm device Procedure for setting the anti-theft alarm deviceProcedure for changing batteries Replacing the lamp Interval of lamp replacementReset of the lamp operation time Replacing the lampTo replace the lamp Cleaning of the lens MaintenanceCleaning of the air-filter Cleaning of the projector and the ventilation slotsNo image appears on the screen TroubleshootingTroubleshooting No image appears on the screen Problem SolutionImages are not displayed correctly Problem Solution Kensington Lock Others Problem SolutionSpecifications Replacement part option/not included in the boxXGA85 SpecificationsWithout terminal cover With terminal cover ConnectorsDimension drawings unit mm Real modeMitsubishi Projector Contact Information

FL7000 specifications

Mitsubishi Electronics has once again showcased its commitment to innovation with the launch of the FL7000 series, a cutting-edge display technology aimed at enhancing visual experiences across various sectors including retail, corporate, and entertainment. The FL7000 series is engineered to deliver stunning image quality, versatility, and advanced features that facilitate seamless integration and usability.

One of the standout characteristics of the FL7000 series is its impressive resolution. With 4K Ultra HD capabilities, it provides crystal-clear images with rich detail, making it an ideal choice for presentations, advertisements, and visual displays. The high brightness levels ensure that images remain vibrant even in well-lit environments, which is crucial for retail and public spaces.

The FL7000 series includes advanced image processing technologies that enhance color accuracy and contrast. With a wide color gamut, it can reproduce a broader spectrum of colors, allowing images to appear more lifelike. The incorporation of HDR (High Dynamic Range) technology further elevates the viewing experience by providing deeper blacks and brighter whites, which is essential for dynamic visual content.

Flexibility and ease of use are other key features of the FL7000 series. The displays are designed for easy installation and integration into existing setups, whether as part of a corporate conference room, a digital signage solution, or a creative installation. The modular design allows for configurations that can adapt to various space constraints and customer needs.

Mitsubishi also emphasizes connectivity in the FL7000 series. The displays come equipped with multiple input options, including HDMI, DisplayPort, and USB interfaces, enabling compatibility with a wide range of media sources. This versatility empowers users to easily switch between different content, making it suitable for dynamic environments.

Additionally, the FL7000 series features an intuitive user interface that simplifies operation and management. Users can configure settings, schedule content, and even manage multiple displays through an integrated software solution, streamlining workflows and enhancing productivity.

In conclusion, the Mitsubishi Electronics FL7000 series sets a new benchmark for display technology, combining high-resolution imaging, advanced processing capabilities, and flexible installation options. Whether used for business, educational purposes, or retail applications, the FL7000 series is poised to transform the way visual information is presented and consumed. With its robust features and technological advancements, it represents a significant advancement in the realm of display solutions.
Top Page Image Contents