Pioneer PDA-5004 Before Proceeding, Checking supplied accessories, How to use this manual

Page 5

Before Proceeding

English

Before Proceeding

Checking supplied accessories

Check that the following accessories were supplied.

1Label for remote control unit PDA-5003

RGB (BNC)

PDA-5004

COMPONENT

2Connector indicator label

PDA-5003

INPUT3

 

INPUT4

 

AUDIO

 

 

 

INPUT5

 

 

 

 

 

VIDEO

INPUT3/4

 

 

ANALOG RGB

 

 

 

AUDIO

S-VIDEO

 

 

 

 

(ON SYNC)

 

(H/V SYNC)

 

 

 

IN

OUT

R

L

G

B

R

HD

VD

R

L

PDA-5004

 

INPUT3

 

 

 

INPUT4

 

 

 

INPUT5

 

 

 

AUDIO

 

VIDEO

 

AUDIO

COMPONENT VIDEO

 

AUDIO

S-VIDEO

R

L

IN

OUT

R

L

Y

Pb/Cb Pr/Cr

R

L

3Screws (⋅2)

(Accessory screws for installing video card)

÷These Operating Instructions

÷Warranty

How to use this manual

This manual has been written to allow easy understanding of setup and operating procedures when the video card PDA-5003/PDA-5004 is installed in the plasma display.

Remove the video card from its packaging and confirm that all accessory parts are present. While installing and setting up the video card, consult the section “Part Names and Functions” starting on page 4 of this manual and in the plasma display’s Operating Instructions to familiarize yourself with the parts of the respective devices. Since this manual makes frequent reference to the names of operating buttons on the plasma display, use the display’s Operating Instructions to familiarize yourself with the controls on the display and the remote control unit.

The section “Installation and Connections” starting on page 6 includes information necessary for installing the video card on the plasma display, together with instructions regarding connections to various other components.

The section “System Settings” starting on page 18 covers the on-screen settings necessary for correct operation of the plasma display with its connected components. Depending on the connections made, this section may or not be necessary.

The remainder of the sections in this manual is dedicated to the basic operations associated with selecting a source component up to the more complex operations associated with adjusting the plasma display picture to match the requirements of specific components and personal preferences.

Regarding menu displays

The example menu displays provided in this manual are those for the PDP-504CMX/PDP-50MXE1/PDP-50MXE1-S model. The PDP-434CMX/PDP-43MXE1/PDP-43MXE1-S display differs as shown:

Please note that the actual contents displayed are the same for both the PDP-504CMX/PDP-50MXE1/PDP- 50MXE1-S and PDP-434CMX/PDP-43MXE1/PDP- 43MXE1-S.

Example of PDP-504CMX/PDP-50MXE1/PDP-50MXE1-S

Menu Display:

 

 

 

 

MENU

 

 

 

INPUT1

PICTURE SCREEN

SETUP

OPTION

CONTRAST

 

:

0

 

BRIGHTNESS

:

0

 

COLOR

 

:

0

 

TINT

 

:

0

 

SHARPNESS

: 0

 

PICTURE RESET

 

 

 

SET

ENTER

 

MENU

EXIT

Example of PDP-434CMX/PDP-43MXE1/PDP-43MXE1-S Menu Display:

MENU

 

 

 

INPUT1

PICTURE

SCREEN

SETUP

OPTION

CONTRAST

:

0

 

 

BRIGHTNESS

:

0

 

 

COLOR

:

0

 

 

TINT

:

0

 

 

SHARPNESS

:

0

 

 

PICTURE RESET

 

 

 

 

SET

ENTER

MENU

EXIT

 

2

En

Page 4 Page 6
Image 5
Page 4 Page 6
Contents PDA-5003 PDA-5004 English Safety PrecautionsSafety Precautions Information to User Safety PrecautionsContents FeaturesHow to use this manual Checking supplied accessoriesBefore Proceeding Regarding menu displaysAbout operations in this manual Picture adjustmentConnection panel Part Names and FunctionsPlasma Display Section Combination IN/OUTVideo Card PDA-5004 Section Video Card PDA-5003 SectionInstallation Installation and ConnectionsInstalling the video card When using PDA-5004 When using PDA-5003Connection to INPUT1 and INPUT5 ConnectionsWhen connecting to Analog RGB in INPUT1 When connecting to Analog RGB INPUT5Connection to INPUT1 or INPUT5 Connection to AV componentsConnection of G on Sync analog RGB source Installation and ConnectionsConnection to a personal computer Installation and ConnectionsConnection of composite Sync analog RGB Source Connection of separate Sync analog RGB SourceTo an external monitor When connecting to Analog RGB OUT INPUT1Component INPUT5 Connection to INPUT4 Connection to INPUT2Connection to INPUT3 Personal computerSignal type Signal format Video Video signalAbout DTV set top box connection INPUT1 INPUT3 INPUT4 INPUT5INPUT1 Audio connectionsINPUT2 INPUT5INPUT4 INPUT3To attach the speed clamps to the display How to route cablesTo remove speed clamps Once in place. Please attach carefullySetting the onscreen display language System SettingsScreen With the desired language displayed, pressColor Decoding setup Settings after connectionsUse the 2/3 buttons to select the display mode Use the 2/3 buttons to select SetupSystem Settings Decoding INPUT1 or INPUT5 When a component other than a computer isConnected, use the 5/∞ buttons to select Color Use the 5/∞ buttons to select Clamp PositionSelecting input source OperationBefore you begin, make sure you have OperationPress the Volume buttons Adjusting sound volumePress the Muting button on the remote control unit Press the Display buttonDuring video signal input For video signalsChanging screen size Screen size selectionEnlarging one part of the screen Operation Press the remote control unit’s Point Zoom ButtonDisplay Point Zoom OFFMultiscreen display To change the position of the subscreen in PinP modeTo exchange the main screen and subscreen inputs To display the currently selected inputAll other cases Automatic power-offTo return to operating mode Picture adjustment PICTURE/SCREEN AdjustmentAdjusting screen POSITION, Clock Phase automatic adjustWhen the button is pressed, the optimum By pressing the Auto SET UP button on either remoteAppear and the Position adjustment only can be When finished with the setting, press the MenuAs follows INPUT2, 3 or 4 is selected, the following screen willPress the SET button To reset Screen mode settings to the defaultScreen mode adjustment items Other Operations Setting the orbiter OrbiterOther Operations Use the 5/∞ buttons to select Mask Control Screen management settings Screen MGTUse the 5/∞ buttons to select Status Use the 2/3 buttons to select Once or RepeatEnergy saving settings Used in Standard mode Power consumption is less than thatWith input signal, but power ÷ MODE2 ......... Brightness is controlled in accordanceReducing video noise DNR Make this setting if video noise is objectionablePress the SET buttton Middle 2 3 MID High 2 3 HighUse the 2/3 buttons to select the desired Mpeg NR setting Use the 2/ 3 buttons to select SetupReducing noise in Mpeg images Mpeg NR High Middle 2 3 LOWEnhance color contour contrast as desired Use the 2/3 buttons to select the desired CTI settingIncreasing color border contrast CTI Use the 2/3 buttons to select the desired Purecinema mode Setting the Purecinema modeUse the 5/∞ buttons to select Purecinema Menu SETButton to exit the menu screen Setting the Color SystemWhen the setup is finished, press the Menu Function setting Factory default setting is OFF Automatic input switchingFunction switches alternately as shown Use the 5/∞ buttons to select Auto FunctionUse the 5/∞ buttons to select Audio OUT About audio output Audio OUTOther Operations Use the 2/3 buttons to select Option FixedAdditional Information SpecificationsPDA-5003 PDA-5004Full Zoom Cinema Wide Video signal compatibilty table INPUT1, INPUT5Appendix DOT by DOT Full Partial AdditionalDOT by DOT Full Zoom InformationPurecinema signal compatibility table INPUT3, INPUT4 Purecinema signal compatibility table INPUT1, INPUT5Purecinema OFF StandardExplanation of Terms Video signalAspect ratio Jack S Video jackPrécautions de sécurité Précautions de sécuritéFrançais Table des matières ParticularitésLes différents organes et leurs rôles ParticularitésAvant de commencer Vérification des accessoires fournisPropos des affichages de menu 50MXE1/PDP-50MXE1-SRéglage de l’IMAGE Description des modes opératoiresAvant de commencer RemarquePanneau de raccordement Les différents organes et leurs rôlesSection Écran à plasma PDP-50MXE1/PDP-50MXE1-SSection Carte vidéo PDA-5004 Section Carte vidéo PDA-5003Installation de la carte vidéo Installation et raccordementsInstallation et raccordements ’installation présente le modèle PDA-5003Raccordements de INPUT1 et INPUT5 Prises d’entrée sur l’écran à plasma avec carte vidéo’emploi du PDA-5003 ’emploi du PDA-5004Pour le raccordement à Analog RGB INPUT5 Raccordement d’un appareil vidéoPour le raccordement à Analog RGB in INPUT1 Reliez cette prise RemarquePour le raccordement à Component Video INPUT5 Raccordement d’une source analogique RVB Utilisez cette solution si l’appareil fournit un signal deRaccordement à un ordinateur Pour le raccordement à Analog RGB OUT INPUT1 Fournissant le signal de synchronisation sur leVert G on Sync Si vous utilisez la prise INPUT5, réglez le sélecteur Fournissant des signaux composites de synchronisationRaccordement de INPUT2 InstallationetraccordementsRaccordement de INPUT4 Raccordement de INPUT3Raccordement au boîtier DTV Signal vidéo Format du signalRaccordement audio pour l’appareil relié à INPUT2 Raccordements audioRaccordement audio pour l’appareil relié à INPUT1 Raccordement audio pour l’appareil relié à INPUT5Raccordement audio pour l’appareil relié à INPUT4 Fixation des colliers rapides à l’écran à plasma Comment faire cheminer les câblesPour retirer les colliers rapides 50MXE1-S avec la carte vidéo PDA-5003Paramétrages du système Mise en œuvre pour Type DE SIGNAL/DÉCODAGE CouleurRéglage de la langue d’affichage sur écran Paramétrages après raccordementComme suit le mode d’affichage Si le signal d’entrée a une fréquence deModifie alternativement comme suit le mode Type DE Signal puis appuyez sur la touche SETPosition Clamp Mise en œuvre pourChoix de la source d’entrée FonctionnementAvant tout, assurez-vous que FonctionnementAppuyez sur les touches Volume Réglage du volume sonoreAppuyez sur la touche Muting de la télécommande Appuyez sur la touche DisplayChangement de la taille de l’écran Avec un signal d’entrée vidéoChoix d’un format d’image Dans le cas des signaux vidéoArrêt 3 x 1.5 3 x 2 3 x Remarque Agrandissement partiel de l’imagePour afficher l’entrée actuellement sélectionnée Affichage multi-écranDans tous les autres cas Pour revenir au mode de fonctionnementChaque pression sur la touche, le réglage change Comme suit ARRÊT/DÉSACTIVÉ MARCHE/ACTIVÉRéglage de l’IMAGE Réglages de l’IMAGE et de l’ÉCRANUtilisez les touches 2/3 pour sélectionner Option Réglages de l’IMAGE et de l’ÉCRANDe menu Paramétrage AutoUtilisez les touches 2/3 pour choisir l’option Écran CranParamètres qui peuvent être réglés Écran Réglage de l’orbiteur Orbiter Autres démarchesPosition de masque latéral Utilisez les touches 5/∞ pour sélectionner OrbiterOption Réglages de gestion d’écranContrôle Masque Utilisez les touches 2/3 pour sélectionner OptionActivation Dénergie Réduction du bruit vidéo DNR Utilisez sur les touches 2/3 pour choisir l’option SetupMoyen 2 3 Moyen Haut Moyen BAS 2 3 BAS 2 3 Haut÷ L’effet de réduction du bruit augmente dans l’ordre Le réglage par défaut effectué en usine est MoyenLa fonction de température de couleur DNR est Réglée et l’écran revient à celui présenté à l’étape’affichage normal Augmentation du contraste du bord de couleur CTIÇais Réglage du mode PurecinemaUtilisez les touches 5/∞ pour choisir Purecinema Autres démarches De menuSystème Couleur Réglage du système couleurLes entrées INPUT3 et INPUT4 sont compatibles avec Utilisez les touches 5/∞ pour choisir Mode Commutation d’entrée automatique Mode AutoAuto Arrêt ENTRÉE4 2 ENTRÉE1La fonction Volume Au besoin, le niveau du signal fourni à la prise Audio÷ Fixe ............... Le volume de sortie audio ne change Pas, même si les commandesInformations complémentaires AccessoiresCaractéristiques techniques GénéralitésTableau de compatibilité des signaux vidéo INPUT1, INPUT5 SupplémentPlein Cinema LargePlein Écran Partiel Signification des symboles50MXE1-S INPUT1, INPUT5 Plein Écran Zoom MentairesNon disponible Arrêt Standard Avancé Arrêt AvancéGlossaire Signal S-vidéoComposantes vidéo Format d’imageAFTER-SALES Service for Pioneer Products

PDA-5004, PDA-5003 specifications

The Pioneer PDA-5004 and PDA-5003 are innovative models in the realm of professional audio and multimedia processing, designed to meet the demands of both live sound and installed audio applications. These two products share many features and technologies, making them aligned in performance and capabilities while catering to slightly different user needs.

The PDA-5004 is equipped with a powerful four-channel amplifier that delivers 500 watts per channel at 4 ohms. This robust output ensures that users can have high-performance sound reinforcement for large venues or installations. In contrast, the PDA-5003 offers a three-channel design with an individual output of 500 watts per channel at 4 ohms, providing a slightly less complex setup while still offering ample power for many applications.

One of the key features of both models is their advanced digital signal processing (DSP) capabilities. This built-in DSP offers a range of features including equalization, crossover settings, and delay functions, allowing audio engineers to fine-tune sound to suit specific environments and preferences. Users can benefit from multiple pre-set configurations designed specifically for different types of audio experiences, from music playback to spoken word events, enhancing versatility.

The units also incorporate a variety of connectivity options, including XLR and RCA inputs, as well as outputs that facilitate integration with other audio devices and systems. They support both balanced and unbalanced connections, making them compatible with a wide range of audio sources. The inclusion of Ethernet connectivity on the PDA-5004 allows for remote control and monitoring via compatible software, offering enhanced convenience for professional users.

In terms of build quality, both amplifiers are designed with durability in mind, featuring a rugged chassis that can withstand the rigors of touring and installation environments. Additionally, their efficient cooling systems prevent overheating during prolonged use, ensuring reliability in demanding situations.

Overall, the Pioneer PDA-5004 and PDA-5003 represent a synthesis of cutting-edge technology and user-friendly features that make them well-suited for professionals seeking high-quality audio performance. With powerful amplification, advanced DSP capabilities, and versatile connectivity options, these models stand out as effective solutions for live sound and permanent installations alike.
Top Page Image Contents