Mitsumi electronic WD3300U user manual EN-23

Page 23

Viewing video images (continued)

D. Projecting images

Preparation:

• Remove the lens cap.

Main power switch

POWER button

 

HDMI button

 

POWER indicator

POWER button

 

 

 

STATUS indicator

 

 

COMPUTER 1, 2 buttons

VIDEO button

 

 

 

ENTER button

ZOOM/FOCUS button

S-VIDEO button

 

COMPUTER/

DVI-D(HDCP) button

 

LENS SHIFT button

 

DVI-D button

 

 

 

 

 

 

p, q, t, u buttons

VIDEO/HDMI button

p, q, t, ubuttons

 

 

 

ZOOM/FOCUS button

 

ENTER button

 

LENS SHIFT button

 

 

1.Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red.

•If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the POWER button may not work after the main power switch is turned ON. (The STATUS indicator blinks green.) After the fan stops rotating, press the POWER button to turn back on the POWER indicator.

2.Turn on the power of the connected video equipment.

3.Press the POWER button.

•It may take about 1 minute for the lamp to light up.

•The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.

•Do not cover the lens with the lens cap while the lamp is on. Do not strip off the aluminium sheet inside the lens cap.

•After the POWER button is pressed, the image may flicker before the lamp becomes stable. This is not a product malfunction.

•The lamp operation becomes stable in 1 minute after the power is turned on and then the lamp mode selected in the menu is activated. During the activation, displayed images may be disturbed.

•The projector starts warming up when the POWER button is pressed. During the warm-up process, images may appear dark and no commands are accepted.

•By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when the STATUS indicator blinks red. (See page 41.)

4.Press the ZOOM/FOCUS button to display the ZOOM/FOCUS menu.

5.Adjust with the or button to get a fine picture.

•When the ENTER button is pressed while the ZOOM/FOCUS menu is displayed, the adjustment mode is switched between FAST and STEP. When FAST is selected, the speed of focus controlled by the or button becomes fast, and it becomes slow when STEP is selected.

6.Select an input source.

•Press the VIDEO/HDMI button on the projector or the VIDEO, S-VIDEO or HDMI button on the remote control that is corresponding to the terminal in use.

•The input source is switched between VIDEO, S-VIDEO and HDMI at every press of the VIDEO/HDMI button on the projector.

•You cannot change the input source while the menu is being displayed.

•Though it may take some time before an image is displayed on the screen depending on the type of the input signal, such symptom is not a malfunction.

•Some images become easier to view when the setting of aspect ratio is changed. (See page 19.)

•When projecting images from a DVD player that is connected to the COMPUTER/COMPONENT VIDEO DVI-D

IN (HDCP) terminal, press the COMPUTER/DVI-D button on the projector to select DVI or press the DVI-D (HDCP) button on the remote control.

•When projecting images from a DVD player that is connected to the COMPUTER/COMPONENT VIDEO IN-1 or

COMPUTER/COMPONENT VIDEO IN-2 terminal, press the COMPUTER/DVI-D button on the projector or the COMPUTER 1 or COMPUTER 2 button on the remote control.

•When COMPUTER 1 or COMPUTER 2 is chosen as the source, images supplied from the computer may flicker. Press theor button on the remote control to reduce flicker, if it occurs. (Fine adjustment)

7.Adjust the position of the projector to keep an appropriate projection distance with which images are projected in their specified sizes.

8.Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 10.)

•When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 11.)

9.Press the ZOOM/FOCUS button to display the ZOOM/FOCUS menu.

10.Adjust with the p or q button to get an approximate size.

•When the ENTER button is pressed while the ZOOM/FOCUS menu is displayed, the adjustment mode is switched between FAST and STEP. When FAST is selected, the speed of zoom controlled by the p or q button becomes fast, and it becomes slow when STEP is selected.

EN-23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents WD3300 EN-2 Contents Important safeguards Do not keep using the damaged projector Important safeguardsPreparing your projector Checking accessoriesInserting the batteries into the remote control Control area 1112 Power jack Main power switchPreparating your projector OverviewAbout the laser beam Remote controlBottom side Reception angle Using the remote controlOperational range of the remote control Using the wired remote controlScreen size and projection distance Setting up your projectorSetting up the screen When the aspect ratio is Full Display at 1280 x 800 pixelsWhen projected images are distorted to a trapezoid Setting up your projectorAdjusting the position of the projected image When fine streaks are seen on projected imagesRear projection Front projection, ceiling mountingViewing computer images Connecting the projector to a computerFor monitor connection Plugging the power cordViewing computer images About DDCInstalling the terminal cover Remove the lens cap Projecting imagesInstant Shut Down To stop projectingAV mute When connecting to a notebook computerSetting of the resolution Example of the setting procedure for external outputWith the Quick Menu or Feature menu Setting the aspect ratioHow to change the settings With the remote control When a TV tuner or VCR is connected Connecting the projector to video equipmentConnecting to a video player, etc When using the BNC connectorConnection for video equipment having an Hdmi terminal Viewing video imagesProjector + DVD player or Hdtv decoder Connection for video equipment having a DVI-D terminal Plugging in the power cordEN-23 Volume from the speaker Menu operation Menu display mode and menu typeMenus displayed in the Quick Menu mode Menus displayed in the Detail Menu modeMenu operation Basic procedure for setting the menusQuick Menu Settings of each menu itemEN-28 Advanced Menu Image menuEN-30 EN-31 User Signal menuTo adjust the tone of white Color Temp Adjusting projected imagesTo adjust the brightness Contrast and Brightness To adjust the color Color and TintColor Enhancer Adjusting projected imagesAbout color temperature YES How to adjust the computer imageLPF Progressive filter Simple method to adjust the image positionTo adjust the horizontal position To adjust the vertical positionTo resume the motion in the image Advanced featuresSetting procedure FreezeTo cancel the password function Advanced featuresPassword function To enable the password functionUP button Mouse remote controlProjector + computer with USB connector OperationConnection Supervising and controlling by computerMajor functions Abnormal condition IndicatorsNormal condition Replacing the lamp Interval of lamp replacementTo replace the lamp Reset of the lamp operation timeReplacing the lamp When removing the lamp from the ceiling-mounted projector MaintenanceCleaning of the projector and the ventilation slots Cleaning of the lensNo image appears on the screen Problem Solution TroubleshootingImages are not displayed correctly Problem Solution TroubleshootingOthers Problem Solution EN-48 Replacement part option/not included in the box SpecificationsXGA85 SpecificationsWithout terminal cover ConnectorsDimension drawings unit mm Real modeMitsubishielectric Corporation

WD3300U specifications

The Mitsumi WD3300U is an advanced electronic device designed to meet the growing demands of modern audio and communication applications. Recognized for its robust construction and versatile functionality, the WD3300U serves as a solution for various electronic interfacing needs.

At the core of the WD3300U is its impressive performance specification. It features a high-speed USB interface, allowing for rapid data transfer rates essential for audio processing and multimedia applications. The device supports USB 2.0 technology, which ensures compatibility with a wide range of existing hardware while providing sufficient bandwidth for optimal operation.

The WD3300U delivers exceptional sound quality, thanks to its integrated high-fidelity audio processing capabilities. It utilizes advanced codecs to enhance audio playback and recording, minimizing distortion and ensuring clear sound reproduction. This feature makes it particularly suitable for professional audio applications, such as recording studios and live audio setups where sound integrity is paramount.

One of the standout characteristics of the Mitsumi WD3300U is its user-friendly design. The device offers plug-and-play functionality, allowing users to easily connect it to compatible systems without the need for complex installation processes. This feature is especially beneficial for professionals who require quick deployment in dynamic environments.

In terms of connectivity, the WD3300U is equipped with multiple input and output options, including standard audio jacks and MIDI connections, catering to a wide variety of devices and ensuring flexibility in setups. Its compact form factor makes it an ideal choice for mobile applications, enabling users to integrate it seamlessly into laptops and portable audio rigs.

The reliability of the Mitsumi WD3300U is further enhanced by its durable construction, designed to withstand the rigors of frequent use. The device is built to endure operational stresses, making it a dependable tool for both casual users and professionals in demanding environments.

Overall, the Mitsumi WD3300U combines cutting-edge technology with practical features, making it a valuable asset for anyone in the audio and communication field. Its blend of performance, ease of use, and durability cements its position as a competitive option in the market for electronic interfacing solutions.
Top Page Image Contents