IBM Partner Pavilion 6793, 6343, 6349, 6791, 6790 To connect an additional IDE CD drive or DVD drive

Page 49

3.Connect one end of the signal cable to the drive and the other to the secondary IDE connector on the system board. To reduce electronic noise, use the connectors at the end of the cable only.

4.Your computer has extra power connectors for additional drives. Connect a power connector to the drive.

5.If you have a CD-ROM audio cable, connect it to the drive and to the system board. See “Identifying parts on the system board” on page 30.

To connect an additional IDE CD drive or DVD drive

1.Locate the secondary IDE connector on the system board and the three-connector signal cable. See “Identifying parts on the system board” on page 30.

2.Connect the extra connector in the signal cable to the new CD drive or DVD drive.

3.Your computer has extra power connectors for additional drives. Connect a power connector to the drive.

To connect an additional IDE hard disk drive

1.Locate the primary IDE connector on the system board. One end of the three-connector cable connects to the hard disk drive and the other connects to the system board. See “Identifying parts on the system board” on page 30.

2.Connect the extra connector in the signal cable to the new hard disk drive.

3.Your computer has extra power connectors for additional drives. Connect a power connector to the drive.

What to do next

vTo work with another option, go to the appropriate section.

vTo complete the installation, go to “Replacing the cover and connecting the cables” on page 38.

Installing a Rope Clip

To help prevent hardware theft, you can add a 3/16 inch or 5 mm Rope Clip and cable to your computer. After you add the security cable, make sure that it does not interfere with other cables that are connected to the computer.

To install a Rope Clip:

1.Remove the cover. See “Removing the cover” on page 29.

2.Use a tool, such as a screwdriver, to remove the two metal knockouts.

3.Insert the Rope Clip through the rear panel; then attach and tighten the nuts with an appropriately sized or adjustable wrench.

4.Replace the computer cover. For more information, see “Replacing the cover and connecting the cables” on page 38.

Chapter 4. Installing internal options — desktop model 37

Image 49
Contents Page Page Page Page Contents Index To connect To disconnect Safety InformationModem safety information Lithium battery noticeConsignes de sécurité relatives au modem Laser compliance statementViii User Guide How this book is organized About this bookInformation resources Identifying your computer OverviewUser Guide Microprocessor FeaturesExpansion Physical specifications small desktop model SpecificationsPhysical specifications desktop model Physical specifications microtower model Tools required Available optionsHandling static-sensitive devices Overview User Guide Locating the connectors on the front of your computer Installing external optionsUSB connector Locating the connectors on the rear of your computer User Guide Installing external options Obtaining device drivers Connector DescriptionRemoving the cover Installing internal options small desktop modelIdentifying parts on the system board Locating componentsInstalling DIMMs Installing memoryWhat to do next Installing adaptersInstalling internal options small desktop model What to do next Drive specifications Installing internal drivesInstalling a drive Installing a Rope Clip Replacing the cover and connecting the cables Installing internal options small desktop model User Guide Installing internal options desktop model Locating components Installing internal options desktop model Installing adapters Installing internal drives Drive specifications Installing a drive To connect the first IDE CD drive or DVD drive To connect an additional IDE CD drive or DVD drive Replacing the cover and connecting the cables Installing internal options desktop model User Guide Installing internal options microtower model Moving the power supply Installing internal options microtower model Installing memory Installing adapters User Guide Installing internal drives Installing a drive Installing internal options microtower model To connect the first IDE CD drive or DVD drive Installing a Rope Clip Replacing the cover and connecting the cables Installing internal options microtower model User Guide Using the IBM Setup Utility program Setting, changing, and deleting a password Administrator passwordErasing a lost or forgotten password clearing Cmos Other settings in the IBM Setup Utility program Using Security Profile by DeviceStartup sequence Changing the startup sequenceUser Guide Appendix A. Changing the battery User Guide Appendix B. Updating System Programs Recovering from a POST/BIOS update failureSystem programs User Guide System memory map Appendix C. System address mapsAddress map LPT3 COM1 DMA I/O address mapAddress hex Description Bits Byte pointer Following tables list the IRQ and DMA channel assignments User Guide Television output notice Appendix E. Notices and trademarksIBM TrademarksDMA IRQ IndexLocation 19, 31 Memory Page Part Number 25P4024