IBM Partner Pavilion 2292 Laser compliance statement, Consignes de sécurité relatives au modem

Page 9

vNever install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

vNever touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

vUse caution when installing or modifying telephone lines.

vAvoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

vDo not use the telephone to report a gas leak in the vicinity of the leak.

Consignes de sécurité relatives au modem

Lors de l’utilisation de votre matériel téléphonique, il est important de respecter les consignes ci-après afin de réduire les risques d’incendie, d’électrocution et d’autres blessures :

vN’installez jamais de cordons téléphoniques durant un orage.

vLes prises téléphoniques ne doivent pas être installées dans des endroits humides, excepté si le modèle a été conçu à cet effet.

vNe touchez jamais un cordon téléphonique ou un terminal non isolé avant que la ligne ait été déconnectée du réseau téléphonique.

vSoyez toujours prudent lorsque vous procédez à l’installation ou à la modification de lignes téléphoniques.

vSi vous devez téléphoner pendant un orage, pour éviter tout risque de choc électrique, utilisez toujours un téléphone sans fil.

vEn cas de fuite de gaz, n’utilisez jamais un téléphone situé à proximité de la fuite.

Laser compliance statement

Some IBM Personal Computer models are equipped from the factory with a CD-ROM drive or a DVD-ROM drive. CD-ROM drives and DVD-ROM drives are also sold separately as options. CD-ROM drives and DVD-ROM drives are laser products. These drives are certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products. Elsewhere, these drives are certified to conform to the requirements of the International Electrotechnical Commission (IEC) 825 and CENELEC EN 60 825 for Class 1 laser products.

When a CD-ROM drive or a DVD-ROM drive is installed, note the following handling instructions.

CAUTION:

Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.

Removing the covers of the CD-ROM drive or DVD-ROM drive could result in exposure to hazardous laser radiation. There are no serviceable parts inside the CD-ROM drive or DVD-ROM drive. Do not remove the drive covers.

Some CD-ROM drives and DVD-ROM drives contain an embedded Class 3A or Class 3B laser diode. Note the following statement.

Safety Information vii

Image 9
Contents Page Page Page Page Contents Index To connect To disconnect Safety InformationModem safety information Lithium battery noticeConsignes de sécurité relatives au modem Laser compliance statementViii User Guide How this book is organized About this bookInformation resources Identifying your computer OverviewUser Guide Microprocessor FeaturesExpansion Physical specifications small desktop model SpecificationsPhysical specifications desktop model Physical specifications microtower model Available options Tools requiredHandling static-sensitive devices Overview User Guide Locating the connectors on the front of your computer Installing external optionsUSB connector Locating the connectors on the rear of your computer User Guide Installing external options Obtaining device drivers Connector DescriptionRemoving the cover Installing internal options small desktop modelIdentifying parts on the system board Locating componentsInstalling DIMMs Installing memoryWhat to do next Installing adaptersInstalling internal options small desktop model What to do next Drive specifications Installing internal drivesInstalling a drive Installing a Rope Clip Replacing the cover and connecting the cables Installing internal options small desktop model User Guide Installing internal options desktop model Locating components Installing internal options desktop model Installing adapters Installing internal drives Drive specifications Installing a drive To connect the first IDE CD drive or DVD drive To connect an additional IDE CD drive or DVD drive Replacing the cover and connecting the cables Installing internal options desktop model User Guide Installing internal options microtower model Moving the power supply Installing internal options microtower model Installing memory Installing adapters User Guide Installing internal drives Installing a drive Installing internal options microtower model To connect the first IDE CD drive or DVD drive Installing a Rope Clip Replacing the cover and connecting the cables Installing internal options microtower model User Guide Using the IBM Setup Utility program Administrator password Setting, changing, and deleting a passwordErasing a lost or forgotten password clearing Cmos Other settings in the IBM Setup Utility program Using Security Profile by DeviceStartup sequence Changing the startup sequenceUser Guide Appendix A. Changing the battery User Guide Recovering from a POST/BIOS update failure Appendix B. Updating System ProgramsSystem programs User Guide Appendix C. System address maps System memory mapAddress map LPT3 COM1 DMA I/O address mapAddress hex Description Bits Byte pointer Following tables list the IRQ and DMA channel assignments User Guide Television output notice Appendix E. Notices and trademarksIBM TrademarksDMA IRQ IndexLocation 19, 31 Memory Page Part Number 25P4024