JVC PC007182399-1 warranty Installation Installation Style, Installation Keystone

Page 39

ENGLISH

Installation > Installation Style

24 Installation Style

Flips the image to the left or right, up or down according to the projection state of the projector.

	Front	Select this for tabletop front projection.
	Ceiling Mount (F)	Select this for ceiling front projection.
	Rear	Select this for tabletop rear projection.
	Ceiling Mount (R)	Select this for ceiling rear projection.

Installation > Keystone

25Keystone

Compensates for trapezoidal distortion caused by installation.

●If the “Shift Adjustment” is excepting 0%, the image may be projected on the screen incorrectly when trapezoidal distortion is compensated. (P21)

Installation > Screen Adjust

26Screen Adjust

Corrects skewed white balance derived from the reflective characteristics of the screen.

	Off	Makes no correction. (Normally set to “off”)
	A	Corrects to slightly reddish.
	B	Corrects to slightly greenish.
	C	Corrects to slightly bluish.

Display Setup > Back Color

27 Back Color

Configures the screen color displayed when there is no input signal.

	Blue	Sets screen color to “Blue” .
	Black	Sets screen color to “Black” .

Display Setup > Menu Position

28 Menu Position

Sets the display position of the menu. The possible positions for displaying the menu are at the four corners or at center of the screen.

Upper-left Upper-right Center Lower-right Lower-left

●This can also be displayed by the remote control. (P14)

Display Setup > Menu Display

29 Menu Display

Sets the duration for displaying the menu.

	15 sec	Display for 15 seconds.
	On	Always display.

Getting Started

Preparation

Basic Operation

Settings

Troubleshooting

Others

39

Image 39

Contents DLA-HD950/DLA-HD990 Machine Noise Information Germany only Safetyf ty PrecautionsPrecautionsAbout the installation place FCC Information U.S.A. onlyEnglish Do not allow any unqualified person to install the unitImportant Europe only Power cordBatterij Producten Battery ProductsBatterie Produkte Pile ProduitsΜπαταρία Προϊόντα Baterías/pilas ProductosBatteria Prodotti Pilha ProdutosAkku Tuotteet Batteri ProdukterAkkumulátor Termékek Батарея ИзделияBaterie Produkty Bateria ProduktyTHX Certification THX CertificationContents Conventions in this manual Check the AccessoriesOptional Accessories About this ManualControls and features Front Side/Left SideRear Side/Top Side/Right Side Bottom Surface Preparation Basic OperationRemote Control Controls and featuresWhen reflecting off a screen How to Use the Remote controlEffective Range of Remote Control Unit When directing the remote control toward this unitPreparation Selecting Connecting DevicesThis unit ConnectingConnecting via Video Cable and S-Video Cable Connecting via Component Video CableConnecting Connecting via Hdmi CableConnecting via HDMI-DVI Conversion Cable This unit BD/DVD player for European market Connecting via SCART-RCA CableConnecting via RGB Video Cable RGB video output terminalsConnecting via PC Cable Connecting via Trigger CableThis unit Screen Left/Right position Installing the Projector and ScreenSet Angle ShiftScreen Size and Projection Distance Installing the Projector and ScreenMemo Projecting Image Insert the power plug to the power outletTurn on the power Adjusts image focus, size zoom, and position shiftFocus Zoom Shift Turn off the powerAbout Cool Down mode You can hide the image temporarilyConvenient Features during Projection Setting the Screen SizeMasking the Surrounding Area of an Image To end Mask the imageStructure of the Settings menu Picture AdjustInput Signal Information InstallationDisplay Setup FunctionSelect Input Signal AspectVideo Setting MenuProcedures for Menu Operation Display the setting menuSetting Menu Picture Adjust Color Temp Setting MenuCopy Picture Adjust GammaCustom Adjustment Value Custom GammaEnhancement All ResetSharpness DetailInput Signal Hdmi Picture Adjust Lens ApertureInput Signal Picture Position Input Signal CompInput Signal Video/S-Video Input Signal PCInput Signal Aspect Video Input Signal Aspect ComputerInput Signal Over Scan Installation Pixel Adjust Input Signal MaskInput Signal Film Mode Installation Lens ControlDisplay Setup Back Color Installation Installation StyleInstallation Keystone Installation Screen AdjustDisplay Setup Language Display Setup Line DisplayDisplay Setup Source Display Display Setup LogoFunction Trigger Function Off TimerFunction High Altitude Mode High Altitude ModeOther items can also be adjusted To end Changing the Initial Setting Picture ModeSelect picture mode Adjust picture qualitySelect Picture Adjust Picture Mode Natural Registering User-defined Picture ModeSelect the picture mode Adjust picture quality Registering User-defined Picture Mode from the MenuTroubleshooting TroubleshootingAre batteries installed correctly? Is the setup of Control with HdmiIs the image correctly adjusted? Has setting been performed forMessage Cause Details What to Do When these Messages Are DisplayedTime Frequency About Warning IndicatorsActions to Be Taken for Warning Mode Indicator Blinking Interval No. Warning Between ContentPull out the lamp unit Replacing the LampRemove the lamp cover Loosen the screws on the lamp unitTighten the screws with a screwdriver Install the new lamp unitTighten the screws of the new lamp unit Attach the lamp coverReplacing the Lamp Resetting Lamp TimeIf the filter is damaged or too dirty to be cleaned Cleaning and Replacing the FilterClean the filter Reinstall the inner filterRS-232C Specifications Command FormatRS-232C Interface Command and data Command Type Data descriptionEnd Remote control code RS-232C InterfaceBinary code RS-232C Communication Examples Operating commandType Command Description Reference commandDirt in the air inlets Copyright and CautionAbout Trademarks and Copyright Dirt on the cabinetMounting this Unit Precautions for MountingSpecifications Effective PC compatible signalsPolarity No.Back Surface SpecificationsTop Surface Bottom Surface FrontIndex Memo