Onkyo SR608 instruction manual Using Audyssey 2EQ, Enter

Page 26

Using Audyssey 2EQ®

1 Turn on the AV receiver and the connected TV.

To create a listening environment in your home theater

On the TV, select the input to which the AV receiver

is connected.

that all listeners will enjoy, Audyssey 2EQ takes measure-

2 Set the speaker setup microphone at the Main Lis-

ments at up to three positions within the listening area.

Position the microphone at ear height of a seated listener

tening Position 1, and connect it to the SETUP

MIC jack.

with the microphone tip pointed directly at the ceiling

 

using a tripod. Do not hold the microphone in your hand

SETUP MIC jack

during measurements as this will produce inaccurate

 

results.

Speaker setup

a First measurement position

microphone

 

Also referred to as the Main Listening Position this

 

refers to the most central position where one would

 

normally sit within the listening environment. 2EQ

 

uses the measurements from this position to calculate

 

speaker distance, level, polarity, and the optimum

The speaker setting menu appears.

crossover value for the subwoofer.

Note

b Second measurement position

• The on-screen setup menus appear only on a TV that is

The right side of the listening area.

connected to the HDMI OUT. If your TV is connected to

c Third measurement position

the MONITOR OUT V or the COMPONENT VIDEO

OUT, use the AV receiver’s display when changing set-

The left side of the listening area.

tings.

 

The distances from position a to b and a to c must be

3 When you’ve finished making the settings, press

at least 1 meter.

 

ENTER.

TV

: Listening area

a to c: Listening position

Note

Make the room as quiet as possible. Background noise and Radio Frequency Interference (RFI) can disrupt the room measure- ments. Close windows, televisions, radios, air conditioners, flu- orescent lights, home appliances, light dimmers, or other devices. Turn off the cell phone (even if it is not in use) or place it away from all audio electronics.

The microphone picks up test tones which played through each speaker as Audyssey 2EQ Room Correction and Speaker Setup run.

Audyssey 2EQ Room Correction and Speaker Setup cannot be performed while a pair of headphones is connected.

2EQ: Auto Setup

 

Speakers Type

Normal

Speaker Terminal Assign

Front High

Front High/Front Wide/Zone2

SurrBack/Front High/Front Wide

Surr Back

If your front speakers are bi-amped, you must select Bi-Amp in the “Speakers Type” setting (41). For hookup information, see “Bi-amping the Front Speakers” (15).

4 Press ENTER.

Audyssey 2EQ Room Correction and Speaker Setup starts.

Test tones are played through each speaker as Audyssey 2EQ Room Correction and Speaker Setup runs. This process takes a few minutes. Please refrain from talking during measurements and do not stand between speakers and the microphone. Do not disconnect the speaker setup microphone during Audyssey 2EQ Room Correction and Speaker Setup, unless you want to cancel the setup.

5 Place the setup microphone at the next position, and then press ENTER.

Audyssey 2EQ performs more measurements. This takes a few minutes.

6 When prompted, repeat step 5.

En

26

Image 26
Contents TX-SR608 Board above the apparatus shall be set 10 cm Always consider the environmental issues and follow10 cm 4 at the rear. The rear edge of the shelf or Away from the rear panel or wall, creating a flue-likePrecautions Installing the Batteries Supplied AccessoriesUsing the Remote Controller Aiming the Remote ControllerContents Processing FeaturesAmplifier MiscellaneousTHX Select2 Plus Front & Rear Panels Front PanelDisplay For detailed information, see the pages in parenthesesRear Panel Power cordUREMOTE Control jack CENTER, FRONT, SURR, Surr Back or Front High or Front WideReturn button Remote ControllerControlling the AV Receiver Controlling the tunerAbout Home Theater Enjoying Home TheaterSpeaker Configuration Connecting the AV ReceiverConnecting Your Speakers Speaker Connection PrecautionsScrew-type speaker terminals Strip 1/2 to 5/8 12 to 15 mm Connecting the Speaker CablesSpeaker cables, and twist the bare wires tightly, as shown North American and Taiwan models SurroundBi-amping the Front Speakers Using Dipole SpeakersConnecting a Powered Subwoofer AV Cables and Jacks About AV ConnectionsConnected image with AV components Hdmi cableAudio return channel ARC function Connecting Components with HdmiJack Signal Components Assignable Connecting External Components FrontHow to record the video System On/Auto Power On Connecting Onkyo uComponentsConnecting Antenna Remote ControlVideo Connection Formats Signal SelectionWhich Connections Should I Use? Audio Connection FormatsTurning Off Turning On/Off the AV ReceiverTurning On Basic Operations Selecting the Language Used for the Onscreen Setup MenusSetting the Display Brightness Playing the Connected ComponentSelecting Speaker Layout Muting the AV Receiver Using the Home MenuUsing the Sleep Timer TV, MUSIC, GAME, and THXChanging the Input Display Using HeadphonesAudyssey 2EQ Room Correction and Speaker Setup Using Audyssey 2EQ EnterUsing a Powered Subwoofer Error MessagesChanging the Speaker Settings Manually Listening to the Radio Using the TunerTuning into Radio Stations Listening to the RadioPresetting FM/AM Stations Using RDS excluding North American modelsRDS program types PTY Finding Stations by Type PTYListening to Traffic News TP Recording Separate AV Sources Connecting a Recording ComponentRecording AV RecordingSelecting Listening Modes Using the Listening ModesListening Mode Buttons Input Source About Listening ModesExplanatory Notes Speaker LayoutListening Modes DSD *7 Resolution AudioDTS-HD Master DTS 96/24 *8Listening Mode Description Input Speaker Source Layout Onkyo-Original DSP Listening Modes Common Procedures in Setup Menu Advanced SetupOn-screen Setup Menus MenuHdmi Input Input/Output AssignMonitor Out BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, TV/CD, PortComponent Video Input Speaker SetupSpeaker Settings Digital Audio InputSurrBack/Front High/Front Wide Speakers TypeSpeaker Terminal Assign Front High/Front Wide/Zone2 FrontLevel Calibration Equalizer SettingsSpeaker Distance THX Audio Setup BGCDolby Audio AdjustMultiplex/Mono Audyssey DSX Source SetupTheater-Dimensional LFE LevelDynamic Volume Reference LevelName Edit IntelliVolumeSync Picture Mode*1*2 Game ModeWide Mode*1*2 Listening Mode Preset OSD Setup Hardware SetupVolume Setup MiscellaneousSirius Settings North American models Tone Control Settings Lock SetupUsing the Audio Settings Late Night Audyssey SettingsSpeaker Levels Music OptimizerAudio Selector Adjusting the Bass & TrebleSetting the Incoming Digital Signal Fixed Mode Audio SelectorConnecting Your Zone 2 Speakers to an Amp in Zone Connecting ZoneConnecting Your Zone 2 Speakers Directly to the AV receiver ZoneSetting the Powered Zone Using Zone Controlling Zone 2 from the AV receiverOperating with the remote controller Controlling Zone 2 with the Remote ControllerAdjusting the Volume for Zone Muting ZoneModels sold are different depending on the region Connecting an Onkyo DockControlling iPod Onkyo Dock CableUsing the Onkyo Dock UP-A1 DockWithout the RI Control Controlling Your iPodRI Dock With the RI ControlRepeat Available buttonsPlaylist e / r Display *7 Muting Album +Controlling Other Components Preprogrammed Remote Control CodesLooking up for Remote Control Code Remote Mode BD/DVD Entering Remote Control CodesRemote Control Codes for Onkyo Components Connected via u TV/CDYou can reset the remote controller to its default settings Resetting Remote Mode ButtonsResetting the Remote Controller Controlling Other ComponentsButtons ON/STANDBY Input TV VOL q / w Guide Mode firstSetup SearchCan’t turn on the AV receiver TroubleshootingStandby indicator flashes red There’s no sound, or it’s very quietAbout DTS signals There’s no sound with a certain signal formatCan’t select the Pure Audio listening mode Only the front speakers produce soundOn screen display does not appear Remote controller doesn’t workBeginning of audio received by an Hdmi in can’t be heard There’s no pictureThere’s no sound AV receiver’s remote controller doesn’t control your iPodSound changes when I connect my headphones There’s no videoCBL/SAT, GAME, or AUX input Video Attoff defaultVideo Attenuation Important Note Regarding Video PlaybackVideo Section SpecificationsAmplifier Section General Tuner SectionAbout Copyright Protection About HdmiSupported Audio Formats Operations that can be performed with p connection Using an RIHD-compatible TV, Player, or RecorderAbout p-compatible components Change each item in the Hdmi Setup as below How to connect and setupConfirm the connecting and setting Confirm the settingsVideo Resolution Chart OutputOnkyo Europe Electronics GmbH Onkyo Europe Electronics GmbH UK Branch

SR608 specifications

The Onkyo SR608 is a versatile 7.2-channel home theater receiver that has gained popularity among audio enthusiasts for its impressive combination of features and performance. Launched as part of Onkyo's highly regarded line of A/V receivers, the SR608 stands out for its robust build quality, advanced technology, and user-friendly design.

One of the key features of the Onkyo SR608 is its onboard support for high-definition audio formats, including Dolby TrueHD and DTS-HD Master Audio. These formats deliver a lossless audio experience, allowing users to enjoy movies and music with unparalleled clarity and detail. Additionally, the receiver is equipped with advanced decoding capabilities, ensuring that it can handle various audio formats from different sources seamlessly.

The SR608 is also noteworthy for its video processing capabilities. It supports video upscaling up to 1080p through its Faroudja DCDi Cinema technology, allowing users to enhance standard-definition content and make it look sharper on high-definition displays. The receiver features multiple HDMI inputs, enabling users to connect a range of devices such as Blu-ray players, gaming consoles, and streaming devices.

Another significant characteristic of the Onkyo SR608 is its robust amplifier section, which delivers a powerful output of 100 watts per channel (into 8 ohms). This ensures that even the most demanding audio tracks can be reproduced with accuracy and depth, making it ideal for a home theater setup that aims to provide an immersive audio experience. The receiver also includes dual subwoofer outputs, allowing for flexible bass management and the ability to create a more dynamic low-frequency response.

For those who appreciate convenience and connectivity, the SR608 comes equipped with a front-panel USB port, providing access to digital music files. Wi-Fi and Bluetooth compatibility can be added through optional adapters, enabling users to stream audio wirelessly from their smartphones or tablets. The receiver is also equipped with Onkyo’s exclusive Audyssey 2EQ technology, which automatically analyzes the acoustics of a room and calibrates the receiver’s settings for optimal sound performance.

In summary, the Onkyo SR608 is a feature-rich A/V receiver that combines powerful audio performance with advanced video processing, making it a favorite among home theater enthusiasts. Its extensive connectivity options, coupled with user-friendly technology, ensure that it remains a strong choice for those looking to build or upgrade their home entertainment system.