Onkyo SR608 Error Messages, Changing the Speaker Settings Manually, Using a Powered Subwoofer

7 Use qw/ to select an option, and then press

ENTER.

2EQ: Auto Setup

	- - Review Speaker Configuration - -
Subwoofer	Yes
Front	Full Band	TV
Center	40Hz
Surround	100Hz
Front Wide	None
Front High	100Hz
Surr Back	120Hz
Surr Back Ch	2ch
Save
Cancel

The options are:

`Save:

Save the calculated settings and exit Audyssey 2EQ® Room Correction and Speaker Setup.

`Cancel:

Cancel Audyssey 2EQ Room Correction and

Speaker Setup.

Note

•You can view the calculated settings for the speaker con- figuration, speaker distances, and speaker levels by using e/r.

8 Disconnect the speaker setup microphone.

Note

•When Audyssey 2EQ Room Correction and Speaker Setup is complete, the “Equalizer” will be set to “Audyssey” (➔ 42). The Audyssey indicator will light (➔ 9).

•You can cancel Audyssey 2EQ Room Correction and Speaker Setup at any point in this procedure simply by disconnecting the setup microphone.

•Do not connect or disconnect any speakers during Audyssey 2EQ Room Correction and Speaker Setup.

•If the AV receiver is muted, it will be unmuted automatically when Audyssey 2EQ Room Correction and Speaker Setup starts.

•Changes to the room after Audyssey 2EQ Room Correction and Speaker Setup requires you run Audyssey 2EQ Room Correc- tion and Speaker Setup again, as room EQ characteristics may have changed.

Error Messages

While Audyssey 2EQ Room Correction and Speaker Setup is in progress, one of the error messages below may appear.

2EQ: Auto Setup

Ambient noise is too high.

Retry

Cancel

Error message

The options are:

`Retry:

Try again.

`Cancel:

Cancel Audyssey 2EQ Room Correction and

Speaker Setup.

• Ambient noise is too high.

The background noise is too loud. Remove the source of the noise and try again.

• Speaker Matching Error!

The number of speakers detected was different from that of the first measurement. Check the speaker con- nection.

• Writing Error!

This message appears if saving fails. Try saving again. If this message appears after 2 or 3 attempts, contact your Onkyo dealer.

• Speaker Detect Error

This message appears if a speaker is not detected. “No” means that no speaker was detected.

Tip

• See “Speaker Configuration” for appropriate settings (➔ 13).

Changing the Speaker Settings Manually

You can manually make changes to the settings found dur- ing Audyssey 2EQ Room Correction and Speaker Setup. See also:

•“Speaker Configuration” (➔ 41)

•“Speaker Distance” (➔ 42)

•“Level Calibration” (➔ 42)

•“Equalizer Settings” (➔ 42)

Note

•Please note that THX recommends any THX main speakers be set to “80Hz(THX)”. If you set up your speakers using Audyssey 2EQ Room Correction and Speaker Setup, please make sure manually that any THX speakers are set to 80 Hz (THX) crossover (➔ 40).

•Sometimes due to the electrical complexities of subwoofers and the interaction with the room, THX recommends setting the level and the distance of the subwoofer manually.

•Sometimes due to interaction with the room, you may notice irregular results when setting the level and/or distance of the main speakers. If this happens, THX recommends setting them manually.

Using a Powered Subwoofer

If you’re using a powered subwoofer and it outputs very
low-frequency sound at a low volume level, it may not be
detected by Audyssey 2EQ Room Correction and Speaker
Setup.
If the “Subwoofer” appears on the “Review Speaker
Configuration” screen as “No”, increase the subwoofer’s
volume to the half-way point, set it to its highest crossover
frequency, and then try running Audyssey 2EQ Room
Correction and Speaker Setup again. Note that if the vol-
ume is set too high and the sound distorts, detection issues
may occur, so use an appropriate volume level. If the sub-
woofer has a low-pass filter switch, set it to Off or Direct.	En
Refer to your subwoofer’s instruction manual for details.

27