JVC DT-V24G1, DT-V20L3G, 0110SKH-MW-MT Daily Operations / Connections, Front panel, Dual Link SDI

Page 6

Daily Operations / Connections

6

7Front panel

Tally lamp

This lamp is controlled by the tally function of the MAKE/TRIGGER terminal.

•You can select the color of the tally lamp from “GREEN” or “RED” (☞ “TALLY SELECT” in “FUNCTION SETTING” on page 16 and “External Control” on page 20).

•“NO EFFECT” is displayed when you press a button which is not available for the current input or signal format (the lamp lights even when the function does not actually work).

•The items controlled by the MAKE system cannot be controlled by the buttons on the front panel (“REMOTE ON” is displayed and the lamps do not light).

The illustration of the monitor is of DT-V24G1.

1Speakers (stereo)

The speakers emit the same audio signal emitted from the AUDIO ASSIGN (MONITOR OUT) terminals (☞ “ 8 AUDIO ASSIGN (MONITOR OUT) terminals” on page 9).

2VOLUME adjustment knob Adjusts the volume.

3Picture adjustment knob PHASE: Adjusts the picture hue. CHROMA: Adjusts the picture color density. BRIGHT: Adjusts the picture brightness. CONTRAST: Adjusts the picture contrast.

•PHASE and CHROMA cannot be adjusted for certain signal formats.

•When “COMPONENT PHASE” is set to “DISABLE” and an NTSC signal is input, PHASE can be adjusted (☞ page 16).

4MUTING button

Turns off the sound when no menu screen is displayed.

•To cancel the function, press the button again or turn the VOLUME adjustment knob.

•Muting function is also canceled when “BALANCE” of “AUDIO SETTING” in the MAIN MENU is changed (☞ page 14).

5/ / / buttons

When a menu screen is displayed

Selects or adjusts menu items (☞ “Menu

Operations” on page 7).

When no menu screen is displayed

Selects the audio channels of EMBEDDED AUDIO signals (☞ “Audio Channel Selection” on page 7).

•Pressing button while holding button displays the SET-UP MENU (☞ “Menu Operations” on page 7).

6MENU button

Activates/deactivates the display of the MAIN MENU (☞ “Menu Operations” on page 7).

7COLOR OFF button/lamp Displays only the luminance signal.

• This function does not work for RGB input signals.

81:1 button/lamp

Displays the picture in the original resolution of the input signal.

•The aspect ratio of the picture may change depending on the input signal.

9AREA MARKER button/lamp Displays/hides the area marker.

•Select the style of the area marker in “MARKER” of the MAIN MENU (☞ page 13).

•This function works only when displaying the picture in 16:9 aspect ratio.

•This function does not work when “AREA MARKER” or “R-AREA MARKER” is set to “OFF” in “MARKER.”

pSAFETY MARKER button/lamp Displays/hides the safety marker.

•Adjust the area of the safety marker in “MARKER” of MAIN MENU (☞ page 13).

•This function does not work when displaying the picture in the 1:1 mode.

•This function does not work when “SAFETY MARKER” or “R-SAFETY MARKER” is set to “OFF” in “MARKER.”

qSCREENS CHECK button/lamp

Displays only the selected element (R, G, or B) of the video signal.

•Each time you press this button, the picture changes in the following order.

RGB (Normal screen)

Red screen

Blue screen

Green screen

wASPECT button/lamp

Changes the aspect ratio of the picture from 4:3 to 16:9 when the picture of 16:9 aspect ratio is squeezed into 4:3 format signal.

•To return to 4:3, press the button again.

•This function does not work when displaying the picture in the 1:1 mode.

eSCOPE button/lamp

Displays/hides the indication of the wave form monitor and vector scope (☞ “SCOPE SETTING” on page 15).

•Each time you press this button, the window changes in the following order.

No display

Wave form monitor

Vector scope

rT.C. (time code) button/lamp Activates/deactivates the display of the time data (time code) contained in the SDI signal (☞ “On the Information Display” on page 7).

•Select the time code type in “INFORMATION” of SET-UP MENU (☞ page 18).

tINPUT SELECT buttons/lamps Selects an input.

SDI 1: E. AUDIO HD/SD SDI (IN 1) terminal

SDI 2: E. AUDIO HD/SD SDI (IN 2) terminal

DUAL LINK SDI:

E.AUDIO HD SDI (IN 1, IN 2) terminal

DVI: DVI-D (HDCP) terminal

COMPO./RGB: COMPO./RGB terminal

VIDEO 1: VIDEO (INPUT 1) terminal

VIDEO 2: VIDEO (INPUT 2) terminal

•The lamp for the selected input lights.

•When “SDI DUAL LINK” is set to “ON” in MAIN MENU, press SDI 1 or SDI 2 to select DUAL LINK (☞ page 12).

yPower lamp

Unlit: The monitor is completely off (the power switch on the rear panel is turned off).

Lights in Green:

The monitor is on.

Lights in orange:

The monitor is off (on standby).

Flashes in orange:

The monitor is in the P. SAVE (power save) mode (☞ “NO SYNC ACTION” in “SYNC FUNCTION” on page 15).

u button

Turns on and off (on standby) the monitor.

•The power switch is equipped on the rear panel of the monitor (☞ 1 on page 8).

Page 5 Page 7
Image 6
Page 5 Page 7
Contents DT-V20L3G Safety Precautions Power ConnectionHow to replace the fuse EMC Supplement Dear CustomerInformation for Users on Disposal of Old Equipment FCC NoticeInstallation To install the standTo detach the stand Higher position Lower position To adjust the stand heightTo prevent an accidental fall Fixing the monitorDaily Operations / Connections Front panelDual Link SDI Display the menu Press buttons to select an item, then press buttonRear panel Attaching the power cord holder DVI-D Hdcp terminalENGLISH9 When a DVI-D signal protected with Hdcp is input Video signalsOn the signal format When no video signal comesStatus indication of Dual Link Status indication of Dual LINK/3G SDI signal informationStatus indication of 3G SDI signal information GNDMenu Configuration-MAIN Menu Picture FunctionSetting of Area MARKER, Safety MARKER, R-AREA Marker MARKER*1*2Settings of E.AUDIO Group Example of the wave form monitor Scope SETTING*1Example of the vector scope Sync FunctionFunction Setting Settings of sub menu PosiSettings of SD43 Large Picture SUB ADJSIZE/POSI. ADJ White Balance SETSetting of Character SET InformationAll reset ENGLISH19Using the MAKE/TRIGGER system External ControlAbout the external control DVI Tally SELSDI COMP./RGBTXD Using the serial communicationRXD RTSBasic command list Functions DataENGLISH23 Troubleshooting Maintenance Self-check programLCD panel SpecificationsGeneral Input/output terminalsFront view Side viewENGLISH27 DT-V24G1/DT-V20L3G Multi Format LCD Monitor

DT-V20L3G, 0110SKH-MW-MT, DT-V24G1 specifications

The JVC DT-V24G1 is a versatile 24-inch broadcast monitor designed for high-end professional applications. This monitor stands out with its full HD resolution of 1920 x 1200 pixels, ensuring that content is displayed with exceptional clarity and detail. Its advanced 10-bit IPS panel provides wide viewing angles, allowing multiple viewers to see the same high-quality image without color distortion. The DT-V24G1 supports various input formats, including SDI, HDMI, and composite, making it compatible with a wide range of video sources.

Another significant feature is the integrated waveform and vectorscope, which assist in professional monitoring and ensure accurate color grading and signal integrity. The DT-V24G1 is also equipped with built-in audio level meters, providing straightforward audio monitoring during production processes. Its flexible mount options add to its utility, allowing for easy integration into any studio setup or mobile broadcast unit.

The JVC DT-V20L3G is another noteworthy model, offering a 20-inch LCD display that delivers stunning picture quality with a native resolution of 1920 x 1080 pixels. This model is particularly suited for applications where space is at a premium, without sacrificing performance. It includes advanced color management tools, which allow for precise control over color reproduction, making it ideal for critical color work in post-production environments.

The DT-V20L3G features multiple input options, including HDMI, SDI, and DisplayPort, ensuring versatility and flexibility across various media types. It also has a compact and lightweight design, facilitating ease of transport for location shoots and smaller studio setups. The monitor’s built-in calibration tools allow users to maintain accurate color settings, ensuring reliability in every viewing condition.

Together, these monitors represent JVC's commitment to providing high-performance, reliable solutions for broadcast professionals. With advanced features, robust technologies, and a focus on user-friendly design, the JVC DT-V24G1 and DT-V20L3G are perfect for those looking to elevate their production quality. Whether in a studio, on location, or during post-production, these monitors stand out as essential tools for any broadcasting setup.
Top Page Image Contents