JVC DT-V17L3DY specifications Troubleshooting

Troubleshooting

Solutions to common problems related to the monitor are described here. If none of the solutions presented here solve the problem, unplug the monitor and consult an authorized dealer or service center.

Symptom			Probable cause and corrective action		Page
	•	Press the		button.	6
	• Turn on the POWER switch or DC switch on the rear panel.				8
No power supply	• Firmly insert the AC power plug or DC 12 V power plug.				8
	• When using a DC 12 V power supply, charge the battery or replace it				8
		with a charged one.
	• Select the correct input using the INPUT SELECT buttons.				6
No picture with the	•	Connect the signal cable firmly.			8
	• Turn on the power of the connected component and set the output				—
power on
		correctly.
	•	Check whether the input signal format is acceptable on the monitor.			9
	•	Adjust the volume level.			6
	•	Deactivate the muting function.			6
No sound	•	Connect the signal cable firmly.			8
	• Turn on the power of the connected component and set the output				—
		correctly.
“OTHERS” or “Out of	•	Check whether the input signal format is acceptable on the monitor.			7, 9
range” appears.
	• Select the correct input using the INPUT SELECT buttons.				6
	•	Connect the signal cable firmly.			8
“NO SYNC” appears.	• Turn on the power of the connected component and output video				—
		signals. Or, check whether the video output of the component (video
		output setting of the VCR or graphic board of the computer) is set
		correctly.
	•	Adjust each picture adjustment knob on the front panel or adjust the			6, 14
		items of “PICTURE SUB ADJ.” in the SET-UP MENU. Or, perform
		“reset” in “PICTURE SUB ADJ.”
	• Check whether the setting of COLOR OFF or SCREENS CHECK				6
Wrong color, no color		buttons are appropriate.
	• Select the proper color system (“COLOR SYSTEM”) in “FUNCTION				14
		SETTING” of the SET-UP MENU.
	• Adjust the items of “WHITE BALANCE SET.” in the SET-UP MENU.				14
		Or, perform “reset” in “WHITE BALANCE SET.”

Symptom		Probable cause and corrective action	Page
The picture becomes	•	Adjust the picture contrast or brightness by using the adjustment	6, 14
		knobs on the front panel. Or, adjust “CONTRAST” or “BRIGHT” of
blurred.
		“PICTURE SUB ADJ.” in the SET-UP MENU.
	•	Check whether the setting of 1:1 or ASPECT buttons is appropriate.	6
	•	Check whether the input signal format is acceptable on the monitor.	9
Wrong picture position,	• Adjust the picture size (H SIZE/V SIZE) or position (H POSITION/V		14
wrong picture size.		POSITION) of “SIZE/POSI. ADJ.” in the SET-UP MENU.
	•	For some signals, the picture cannot be displayed fully in the effective	—
		screen area. There is no sure method to solve this problem.
	•	The items which are not available for the current input or the current	—
Some items do not		input signal are not displayed on the menu. Change the input or the
		input signal.
appear on the menu.
	• The items controlled by the MAKE system do not appear on the		17
		menu.
Buttons on the monitor	• Set “CONTROL LOCK” in the SET-UP MENU to “OFF.”		15
	•	You cannot use the buttons for the items controlled by the MAKE	16,17
do not work.
		system. Disable the external control.

The following are not malfunctions.

•When a still image is displayed for a long time, it may remain indistinctly on the screen after the picture has changed. Though the remaining picture will disappear after a while, there may be a case that it remains for a long period depending on the length of time the still image was displayed for. This is due to the characteristics of the LCD display and is not a malfunction.

•Red spots, blue spots and green spots on the panel surface are a normal characteristic of LCD displays, and not a problem. The LCD display is built with very high precision technology; however, be aware that a few pixels may be missing or constantly lit.

•The following symptoms are problems only when pictures or sounds are not played back normally.

–A slight electric shock occurs when you touch the monitor.

–The top and/or rear panel of the monitor becomes hot.

–The monitor emits a cracking noise.

–The monitor emits a mechanical noise.

19