JVC DT-V17L3DY specifications Front panel

Page 6

Daily Operations / Connections

6

7Front panel

Tally lamp

This lamp is controlled by the tally function of the MAKE/TRIGGER terminal.

•You can select the color of the tally lamp from “GREEN” or “RED”.

☞“ TALLY SELECT” in “FUNCTION SETTING” on page 14 and “External Control” on page 16

•“NO EFFECT” is displayed when you press a button which is not available for the current input or signal format (the lamp lights even when the function does not actually work).

•The items controlled by the MAKE system cannot be controlled by the buttons on the front panel (“REMOTE ON” is displayed and the lamps do not light).

1Speakers (stereo)

The speakers emit the same audio signal emitted from the AUDIO (MONITOR OUT) terminals.

(☞ “ 5 AUDIO (MONITOR OUT) terminals” on page 8)

2VOLUME adjustment knob Adjusts the volume.

3Picture adjustment knob PHASE: Adjusts the picture hue. CHROMA: Adjusts the picture color density. BRIGHT: Adjusts the picture brightness. CONTRAST: Adjusts the picture contrast.

4MUTING button

Turns off the sound when no menu screen is displayed.

•To cancel the function, press the button again or turn the VOLUME adjustment knob.

•Muting function is also canceled when “BALANCE” of “AUDIO SETTING” in the MAIN MENU is changed (☞ page 12).

5/ / / buttons

When a menu screen is displayed

Selects or adjusts menu items. (☞ “Menu

Operations” on page 7)

When no menu screen is displayed

Selects the audio channels of EMBEDDED AUDIO signals. (☞ “Audio Channel Selection” on page 7)

•Pressing button while holding button displays the SET-UP MENU. (☞ “Menu Operations” on page 7)

6MENU button

Activates/deactivates the display of the MAIN MENU. (☞ “Menu Operations” on page 7)

7COLOR OFF button/lamp Displays only the luminance signal.

• This function does not work for RGB input signals.

81:1 button/lamp

Displays the picture in the original resolution of the input signal.

•The aspect ratio of the picture may change depending on the input signal.

9AREA MARKER button/lamp Displays/hides the area marker.

•Select the style of the area marker in “MARKER” of the MAIN MENU (☞ page 11).

•This function works only when displaying the picture in 16:9 aspect ratio.

•This function does not work when “AREA MARKER” or “R-AREA MARKER” is set to “OFF” in “MARKER.”

pSAFETY MARKER button/lamp Displays/hides the safety marker.

•Adjust the area of the safety marker in “MARKER” of the MAIN MENU (☞ page 11).

•This function does not work when displaying the picture in the 1:1 mode.

•This function does not work when “SAFETY MARKER” or “R-SAFETY MARKER” is set to “OFF” in “MARKER.”

qSCREENS CHECK button/lamp

Displays only the selected element (R, G, or B) of the video signal.

•Each time you press this button, the screen changes in the following order.

RGB (Normal screen)

Red screen

Blue screen

Green screen

wASPECT button/lamp

Changes the aspect ratio of the picture from 4:3 to 16:9 when the picture of 16:9 aspect ratio is squeezed into 4:3 format signal.

•To return to 4:3, press the button again.

•This function does not work when displaying the picture in the 1:1 mode.

eWAVE FORM button/lamp

Displays/hides the indication of the wave form monitor.

•Adjust the settings of the wave form monitor in “WAVE FORM SETTING” of the MAIN MENU (☞ page 13).

•The closed caption (☞ page 13) disappears when the wave form monitor is displayed.

rT.C. (time code) button/lamp Activates/deactivates the display of the time data (time code) contained in the SDI signal.

(☞ “On the Information Display” on page 7)

tINPUT SELECT buttons/lamps Selects an input.

SDI 1: E. AUDIO HD/SD SDI (IN 1) terminal

SDI 2: E. AUDIO HD/SD SDI (IN 2) terminal

DVI: DVI-D (HDCP) terminal

COMPO.: COMPO. terminal

VIDEO: VIDEO terminal

• The lamp for the selected input lights.

yPower lamp

Unlit: The monitor is completely off (both the POWER switch and DC switch on the rear panel are turned off).

Lights in Green: The monitor is on.

Lights in orange: The monitor is off (on standby).

Flashes in orange: The monitor is in the P. SAVE (power save) mode (☞ “NO SYNC ACTION” in “SYNC FUNCTION” on page 13).

u button

Turns on and off (on standby) the monitor.

•The power switches (the POWER switch and DC switch) are equipped on the rear panel of the monitor (☞ p, w on page 8).

•To turn off the monitor completely, turn off the POWER switch and DC switch.

i DC lamp

When the DC 12 V power voltage is being lowered due to the battery consumption, the lamp changes to orange from green. When the voltage becomes lower than a certain level, the monitor automatically turns off and the lamp turns to red.

•Make sure to turn off the POWER switch and DC switch on the rear panel before replacing the battery.

•The length of time that the lamp lights in orange differs depending on the type of battery or the battery condition. It is recommended to replace the battery when the lamp turns to orange.

Page 5 Page 7
Image 6
Page 5 Page 7
Contents DT-V17L3DY Safety Precautions These openings must not be blocked or coveredImportant Safety Instructions To detach the stand InstallationTo install the stand You can tilt the monitor as followsTo prevent an accidental fall To adjust the stand heightFix the monitor to a wall by using strings Higher position Lower positionFront panel Press buttons to select an item, then press button Press or button when a menu is not displayedDisplay the menu Press Menu buttonDaily Operations / Connections Rear panelVideo signals Available signalsAttaching the power cord holder Computer signals preset DVI-D Hdcp terminalsPicture Function Menu Configuration-MAIN MenuSetting value -20 +20 Operation guideSetting of Area MARKER, Safety MARKER, R-AREA Marker Settings for marker functions 1/2MARKER*1*2 Settings of E.AUDIO Group Wave Form SETTING*1 Example of the wave form monitorSync Function Settings of sub menu Posi Settings of SD43 LargeControl Lock Setting value OFF, on Setting of Character SETSettings for the information display of the monitor InformationControl priority is as follows External ControlAbout the external control MAKE/TRIGGER systemOperation of the external control Using the MAKE/TRIGGER systemTo assign the functions to the pin terminals Functions controlled by the MAKE/TRIGGER systemCommand outline Using the serial communicationCommunication specifications Basic command listTroubleshooting Screen Maintenance20Unplug this product from the wall outlet before cleaning CabinetInput/output terminals SpecificationsGeneral VideoSide view Dimensions Unit mm inchFront view Rear viewPage DT-V17L3DY Multi Format LCD Monitor

DT-V17L3DY specifications

The JVC DT-V17L3DY is a compact, high-performance 17-inch LCD monitor designed for professional video applications. Tailored for broadcast and production environments, it delivers exceptional image quality and a range of features suited for demanding tasks.

One of the standout characteristics of the DT-V17L3DY is its high-resolution display, featuring a native resolution of 1920 x 1080 pixels, which is capable of displaying Full HD content with impressive clarity. The monitor boasts a wide viewing angle, ensuring that images remain consistent and vibrant from various positions. This is particularly advantageous in multi-user environments, such as control rooms or collaborative studios, where several individuals may be viewing the screen simultaneously.

The DT-V17L3DY utilizes advanced color reproduction technologies, resulting in rich and accurate colors. With a high contrast ratio, it provides deep blacks and bright whites, enhancing the overall viewing experience. To further refine color accuracy, it supports a built-in color calibration feature, allowing users to adjust settings according to specific requirements or standards, making it an excellent choice for color-critical work such as film and video production.

In terms of connectivity, the monitor is equipped with a variety of input options, including HDMI, SDI, and analog connections. This versatility ensures compatibility with a wide range of video sources, accommodating different workflows and setups. Furthermore, the DT-V17L3DY supports both interlaced and progressive signal formats, making it adaptable to a broad spectrum of broadcasting standards.

The monitor's ergonomic design features a sturdy and lightweight chassis, making it suitable for both desktop and rack-mounted applications. Its flexible mounting options allow for easy integration into any setup, whether in a studio, on location, or within an OB van.

Additional features include embedded audio monitoring capabilities, allowing users to check audio levels directly from the monitor, and a set of user-friendly controls for adjusting settings quickly and intuitively. This combination of advanced technology, exceptional display quality, and practical usability makes the JVC DT-V17L3DY a reliable choice for professionals in the video production industry. Whether used for editing, monitoring, or playback, this monitor stands out as a valuable tool for achieving the highest standards in broadcast quality.
Top Page Image Contents