Knoll Systems LED1081 user manual Turning on the Power, Changing the OSD Language, Rear Projection

Page 31

3.5 Turning on the Power

1.Press the ON button on the remote control to turn on the LED1081. The power LED indicator flashes green to indicate that it is warming up.

2.When the projector is ready for use, the LED indicator turns off, and the projector lights.

3.6 Changing the OSD Language

The LED1081 can display the menus in English, Español, Français, Deutsch, Nederlands, Italiano, 繁體中文, and 简体中文.

Enter the OSD, select Language in SETUP menu, then press the or buttons to select a language. Then, press ENTER to confirm your selection.

3.7 Adjusting the Picture Orientation

If the LED1081 is installed behind the screen, you must change the picture orientation to match the installation meth- od. To do this, press MENU on the remote control. Then, select SETUP from the Main Menu.

Rear Projection

If the projector is used in a rear-projection application, press repeatedly to select Rear Projection from the SETUP Menu. Press or to set it to On.

Ceiling Mode

If the projector is ceiling-mounted, the LED1081 automatically inverts the image. If this automatic inversion is not de- sired, select Ceiling Mode from the SETUP Menu and set it to Off.

insTallaTion 1

Image 31

Contents Projector Table of Contents Maintenance and Troubleshooting About this manual Copyright InformationCopyright DisclaimerImportant Safety Instructions FCC Part Textual and Graphic Conventions IntroductionAbout This Manual Target AudienceIf you need Using This ManualTurn to Key Features and Benefits Description, Features and BenefitsParts List Additional Features of the LED1081LED1081 at a Glance Controls and FunctionsLED1081 Top/ Rear/ Bottom View Component LED1081 I/O PanelSource LED10801 Key PadCONT, BRIGHT, Sharp LED1081 Remote ControlRemote Control InstallationIR Reception Angles Advantages Considerations Installation ConsiderationsInstallation Type Ambient LightEstimated Throw Distance Throw DistanceVertical and Horizontal Position Floor InstallationOther Considerations Folded OpticsVertical Lens Shift Lens Shift15H Ceiling Mounting Inverted Adjusting the Projection AngleMounting the LED1081 Floor Mounting UprightConnections to the LED1081 Connecting Source Components to the LED1081RGB Connections Component Video Connections 10 Composite and S-Video Connections 11 RS-232 Control System Connection RS-232 Controller ConnectionConnecting to AC Power Connecting an External IR ReceiverChanging the OSD Language Turning on the PowerAdjusting the Picture Orientation Ceiling ModeFocus Lens AdjustmentsZoom Vertical Lens Shift Horizontal Lens Shift Selecting An Input Source Using the On-Screen MenusOperation Selecting an Aspect RatioLED1081 OSD Menu Structure General PIP PIP Split Mode Memory Sub-Menu Image Aspect Ratio Settings Below Black Above Black 10 Typical Gray Bar Pattern for Adjusting Contrast 12 Typical Test Pattern for Adjusting Sharpness 13 Noise Reduction Sub-Menu 14 Overscan Examples 15 HSG Sub-Menu Advanced OperaTion 4 17 RGB Adjust Sub-Menu 18 Fine Sync Sub-Menu Setup Trigger commands are deactivated when a PIP source is active Info Cleaning the Intake and Exhaust Vents TroubleshootingMaintenanceCleaning the Air Vents Symptom Possible Causes Solution Troubleshooting TipsTransfer Specifications Serial Interface SpecificationsSpecifications IR Codes and Keynames Remote Button Description RS-232 CommandsIR Codes and Keynames Operation Command Values Function Command Action on unit= RGB = PBP = LED Operations Commands Optics LED1081 SpecificationsElectrical Mechanical Standard AccessoriesShows the LED1081 dimensions, in millimeters LED1081 DimensionsSupported Timings Sdtv Projection Distance and Screen Size Specifications Specifications Specifications