Knoll Systems LED1081 user manual IR Codes and Keynames

Page 59

IR Codes and Keynames

No.	Code 1	Keyname	Remote Button	Description
14.	0x8B	src.1		Switch the active source to HDMI 1.
15.	0x8C	src.2		Switch the active source to HDMI 2.
16.	0x8D	src.3		Switch the active source to RGB.
17.	0x8E	src.4		Switch the active source to COMP 1.
18.	0x8F	src.5		Switch the active source to VIDEO.
19.	0x89	src.6		Switch the active source to COMP 2.
20.	0x93	osc.sw		Switch to the next Overscan mode.
21.	0x98	mem.1		Recall user memory associated with the User 1 key.
22.	0x99	mem.2		Recall user memory associated with the User 2 key.
23.	0x9A	color.temp		Switch the color temperature.
24.	0x9D	asp.sw		Switch to the next aspect ratio.
25.	0xA3	pip.sw		Switch to next “PIP Select” state.
26.	0xAA	pip.swap		Swap the PIP image with the active source image.
27.	0xAD			Changes the OSD menu position when OSD is activated.

Table 6-1: IR Codes and Keynames

Serial Interface Specifications 59

Image 59

Contents Projector Table of Contents Maintenance and Troubleshooting About this manual Copyright InformationCopyright DisclaimerImportant Safety Instructions FCC Part Textual and Graphic Conventions IntroductionAbout This Manual Target AudienceTurn to Using This ManualIf you need Key Features and Benefits Description, Features and BenefitsParts List Additional Features of the LED1081LED1081 at a Glance Controls and FunctionsLED1081 Top/ Rear/ Bottom View Component LED1081 I/O PanelSource LED10801 Key PadCONT, BRIGHT, Sharp LED1081 Remote ControlRemote Control InstallationIR Reception Angles Advantages Considerations Installation ConsiderationsInstallation Type Ambient LightEstimated Throw Distance Throw DistanceVertical and Horizontal Position Floor InstallationOther Considerations Folded OpticsVertical Lens Shift Lens Shift15H Ceiling Mounting Inverted Adjusting the Projection AngleMounting the LED1081 Floor Mounting UprightConnections to the LED1081 Connecting Source Components to the LED1081RGB Connections Component Video Connections 10 Composite and S-Video Connections 11 RS-232 Control System Connection RS-232 Controller ConnectionConnecting to AC Power Connecting an External IR ReceiverChanging the OSD Language Turning on the PowerAdjusting the Picture Orientation Ceiling ModeZoom Lens AdjustmentsFocus Vertical Lens Shift Horizontal Lens Shift Selecting An Input Source Using the On-Screen MenusOperation Selecting an Aspect RatioLED1081 OSD Menu Structure General PIP PIP Split Mode Memory Sub-Menu Image Aspect Ratio Settings Below Black Above Black 10 Typical Gray Bar Pattern for Adjusting Contrast 12 Typical Test Pattern for Adjusting Sharpness 13 Noise Reduction Sub-Menu 14 Overscan Examples 15 HSG Sub-Menu Advanced OperaTion 4 17 RGB Adjust Sub-Menu 18 Fine Sync Sub-Menu Setup Trigger commands are deactivated when a PIP source is active Info Cleaning the Air Vents TroubleshootingMaintenanceCleaning the Intake and Exhaust Vents Symptom Possible Causes Solution Troubleshooting TipsSpecifications Serial Interface SpecificationsTransfer Specifications IR Codes and Keynames Remote Button Description RS-232 CommandsIR Codes and Keynames Operation Command Values Function Command Action on unit= RGB = PBP = LED Operations Commands Electrical LED1081 SpecificationsOptics Mechanical Standard AccessoriesShows the LED1081 dimensions, in millimeters LED1081 DimensionsSupported Timings Sdtv Projection Distance and Screen Size Specifications Specifications Specifications