Runco CW-50MC manual RS-232C Commands, How to read this table

Page 23

RS-232C Commands

How to read this table:

RS-232C Adjustment Validity: Indicates whether or not the RS-232 adjustment mode can be used.

• Normal Validity:

Indicates whether or not the normal-operation mode can be used

• Numerical Direct Validity:

When a number (3-digit number) is attached to the end of a command, the command can

 

directly set that adjustment value.

○ or ●: Valid

No Mark: Invalid

 

 

NOTE: = values not stored in the last memory

 

 

 

 

 

 

 

 

 

Name

Full Name

Adjustment

Validity

Direct

 

Description

 

Command

RS-232C

Normal

Numerical

 

 

 

 

 

Validity

 

Validity

 

 

A

AJN

-

 

 

 

Terminates the RS-232C installer adjustment mode.

 

AJY

ADJUST: ON

 

 

 

Starts the RS-232C installer adjustment mode.

 

AMN

AUDIO MUTING: OFF

 

 

Turns audio mute OFF.

 

 

 

 

 

 

 

 

 

AMY

AUDIO MUTING: ON

 

 

Turns audio mute ON.

 

AST

AUTO SET UP MODE

 

 

 

Executes AUTO SETUP.

 

 

 

 

 

 

 

 

B

BHI

B GAIN

 

 

Adjusts BLUE GAIN HIGH-LIGHT.

 

BLW

B OFFSET

 

 

Adjusts BLUE OFFSET LOW-LIGHT.

 

BRA

BAUD RATE: #####-232C

 

 

 

Displays the current baud rate.

 

 

 

 

 

 

 

 

 

BRAS01

BAUD RATE: 1200-232C

 

 

 

Sets the UART setting to 232C (1200bps).

 

BRAS02

BAUD RATE: 2400-232C

 

 

 

Sets the UART setting to 232C (2400bps).

 

BRAS03

BAUD RATE: 4800-232C

 

 

 

Sets the UART setting to 232C (4800bps).

 

BRAS04

BAUD RATE: 9600-232C

 

 

 

Sets the UART setting to 232C (9600bps).

 

BRAS05

BAUD RATE: 19200-232C

 

 

 

Sets the UART setting to 232C (19200bps).

 

BRAS06

BAUD RATE: 38400-232C

 

 

 

Sets the UART setting to 232C (38400bps).

 

BRT

BRIGHTNESS: ***

 

 

Adjusts brightness.

 

BSL

B SIDEBAR ADJ. LEVEL

 

 

Adjusts BLUE SIDEBAR ADJUST LEVEL.

C

CFR

FREQ. ADJ.: ***

 

 

Adjusts the clock frequency (PLL frequency).

 

CGB

C. DETAIL BLUE: ***

 

 

Adjusts color detail BLUE.

 

CGC

C. DETAIL CYAN: ***

 

 

Adjusts color detail CYAN.

 

CGG

C. DETAIL GREEN: ***

 

 

Adjusts color detail GREEN.

 

 

 

 

 

 

 

 

 

CGM

C. DETAIL MAGENTA: ***

 

 

Adjusts color detail MAGENTA.

 

 

 

 

 

 

 

 

 

CGR

C. DETAIL RED: ***

 

 

Adjusts color detail RED.

 

 

 

 

 

 

 

 

 

CGY

C. DETAIL YELLOW: ***

 

 

Adjusts color detail YELLOW.

 

CLS

COLOR SYSTEM: #####

 

 

 

Displays the current color system.

 

 

 

 

 

 

 

 

 

CLSS01

COLOR SYSTEM: AUTO

 

 

 

Sets the color system to AUTO.

 

CLSS02

COLOR SYSTEM: NTSC

 

 

 

Sets the color system to NTSC.

 

CLSS03

COLOR SYSTEM: PAL

 

 

 

Sets the color system to PAL.

 

CLSS04

COLOR SYSTEM: SECAM

 

 

 

Sets the color system to SECAM.

 

CLSS05

COLOR SYSTEM: 4.43NTSC

 

 

 

Sets the color system to 4.43NTSC.

 

CLSS06

COLOR SYSTEM: PAL M

 

 

 

Sets the color system to PAL M.

 

 

 

 

 

 

 

 

 

CLSS07

COLOR SYSTEM: PAL N

 

 

 

Sets the color system to PAL N.

 

CM1

NORMAL

 

 

Sets the Normal color mode.

 

CM2

ISF

 

 

Sets the ISF color mode (retake).

 

CNT

CONTRAST: ***

 

 

Adjusts contrast.

 

COF

COLOR OFF: ********

 

 

 

Displays the current COLOR OFF setting.

 

COFS00

COLOR OFF: DISABLE

 

 

 

Disables COLOR OFF.

 

COFS01

COLOR OFF: ENABLE

 

 

 

Enables COLOR OFF.

 

COL

COLOR: ***

 

 

 

 

CPH

PHASE ADJ.: ***

 

 

Adjusts the phase (PLL phase).

22

Image 23
Contents CW-43MC CW-50MC Contents Introduction Features and BenefitsAvertissement DOC avis de conformation DOC compliance NoticeWhat is Covered Under the Terms of this Limited Warranty Limited WarrantyRIGHTS, Limits and Exclusions General Overview OperationInputs and Controls Audio Output Stereo mini jack Main Power switchDigital RGB INPUT2 DVI-D jack-non Hdcp Audio INPUT2 Stereo mini jackModular Controller Card Input Connections Connecting the Plasma DisplayFront Panel Standby IndicatorOn Indicator Remote Control SensorPlasma Remote Control Remote Control DescriptionMenus for Video NTSC, PAL or Digital 480P and Hdtv This menu will appear only when displayed for video Menus for PC/HDTV-I D-SUB Input Screen Tab Picture TabWhite BAL. Tab Option Tab Setup TabUnits wide Units tall Aspect RatiosRS-232C Adjustment Mode Data Format Protocol From computer to plasmas display How to read this table RS-232C CommandsCommand Full Name RS-232C Normal Numerical Command RS-232C Function PLN BRT. Enhance OFF UPO GET Commands GPI GET Picture Data Gets installer/Picture data GSS GET Status Setup Gets menu and installer Setup data GSO GET Status Option Gets menu and installer Option data Dimensions CW-50MC Plasma CW-43MC CW-50MC SpecificationsRUMA-011000 11-08-04