Onkyo TX-SR500 appendix Connecting the power/Turning on the AV Receiver, Press STANDBY/ON

Page 17

Connecting the power/Turning on the AV Receiver

STANDBY/ON	STANDBY/ON
STANDBY/ON
	STANDBY indicator

POWER

Before connecting

•Make sure that all the connections from pages 10 to 16 are complete.

•Turning on the AV Receiver may cause a momentary power surge, which might interfere with other electrical equipment such as computers. If this happens, use a wall outlet on a different circuit.

1.Connect the power cord (mains lead) to a wall outlet (the mains).

2.(Other than USA and Canadian models only) Press POWER to switch on the main power.

The TX-SR500/TX-SR500E enters standby mode. The STANDBY indicator lights up.

Notes

•The TX-SR500/TX-SR500E is shipped with the main power (POWER) switch in the on position (_) ON.

•To switch off the main power, press the POWER switch again.

•The buttons on the remote controller don’t operate if the POWER switch is set to OFF.

3.Press STANDBY/ON.

The AV Receiver turns on.

The ON indicator and display on the AV Receiver’s front panel light. At the same time, the STANDBY indicator goes off.

Note

To turn off the AV Receiver, press STANDBY/ON. The AV Receiver enters standby mode. Be sure to set the volume to minimum before turning off the AV receiver.

17

Image 17

Contents TX-SR500 TX-SR500E Avis Important safeguardsPrecautions Supplied accessories FeaturesPrecautions Amplifier FeaturesSetting the voltage selector Worldwide models only Before using the unitSetting the AM tuning step frequency Worldwide models only Using the remote controllerIndex to parts and controls Index to parts and controls Rear panel ZREMOTE ControlAntenna 14 Tape IN/OUT= Mode buttons Preset 2/3 button@ Adjust 2/3 button # Volume 5/∞ button 21About Digital Input Optical jack Connecting to audio/video equipmentAbout the DVD, Video 1, Video 2 and Monitor OUT jacks Connecting to audio/video equipmentOretc Do NOTCENTERconnectUsing the provided speaker labels Positioning speakers/Connecting speakersStandard speaker placement of the Speakers a system How to connect to the Front Speakers B terminals Positioning speakers/Connecting speakersConnecting to Speakers a Connecting to Speakers BConnecting the supplied FM and AM indoor antennas aerials Connecting antennasAdjusting the position of the FM indoor antenna aerial Adjusting the position of the AM indoor antenna aerialConnecting an FM outdoor antenna aerial Connecting antennasConnecting an AM outdoor antenna aerial Directional IinkagePower on/ready function Connections for remote control zPower off function Direct change functionPress STANDBY/ON Connecting the power/Turning on the AV ReceiverPress Speaker Adjust twice Speaker setupSetting the crossover frequency Speaker setup → Subwoofer Mode Setting the subwoofer mode Press Subwoofer Mode on the unitSubwoofer Mode Adjusting each speaker’s relative volume balance Test toneAbout digital sound Playing the connected sourcePlaying the connected source Switch the source from Tape to MD Using multi channel inputTo restore the display Direct CH SEL Level 5/∞Listening to the radio Tuning manuallyPress Memory while holding down Press TunerSelecting preset stations Presetting radio stationsPress Tuner to switch the input source to the tuner Listening to the radioListening through headphones Muting the sound remote controller only Press MutingVarious functions common to all the sources Turning on/off the Speakers A/SPEAKERS B systemsChanging the display Press Display Using the sleep timer remote controller only Press SleepVarious functions common to all the sources Level 5/∞ Setting the input signal formatTo fix the digital signal to DTS or PCM Bass adjustment Using the Audio Adjust functionTreble adjustment Late night functionEnjoying the listening modes Enjoying the listening modes Input sources and available listening modeWhen the sound is Dolby Digital Selecting the listening modeWhen the sound is Pro Logic II Movie, Dolby Digital or DTS Various functions while playing surround soundStart recording at the recording component as desired Recording a sourceVideo camera CD playerControlling an Onkyo DVD player Using remote controllerDVD operation buttons OSD operation buttonsControlling an Onkyo CD player Using remote controllerControlling an Onkyo cassette tape deck Press RCVR/TAPE Press the desired operation buttonTV DVD Numeric buttonsControlling a DVD player When entering the code of Onkyo DVD playersAmplifier Remote controller Symptoms Causes Remedies Pages TroubleshootingWhen incorrect operation is observed TroubleshootingSymptoms Causes Remedies OtherOnkyo Europe Electronics GmbH SpecificationsPage Page Page Page Page Page Page Page

Related manuals

Manual 4 pages 32.82 Kb