Sharp XV-Z17000 5Setting the Video System 7Adjusting the Dynamic Range, 8Signal Info

Page 44

Computer Image Adjustment (“SIG-ADJ” Menu) (Continued)

Menu operation Page 35

5Setting the Video System

7Adjusting the Dynamic Range

The video input system mode is factory preset to “Auto”; however, a clear picture from the connected audio-visual equipment may not be received, depending on the video signal difference. In that case, switch the video signal.

Selectable items

Auto

PAL

SECAM

*NTSC4.43

NTSC3.58

PAL-M

PAL-N

PAL-60

*When reproducing NTSC signals in PAL video equip- ment.

An optimum picture may not be displayed if an HDMI- capable device’s output signal type and the projector’s input signal type do not match. If this should occur, switch “Dynamic Range”.

Selectable items

Description

Auto

In most circumstances, “Auto” should

 

be selected.

 

 

Standard

When the black levels of the image

 

show banding or appear faded, select

Enhanced

the item that results in the best picture

 

 

quality.

8Signal Info

Input signal information is displayed.

Note

The video signal can only be set in VIDEO or S-VIDEO mode.

When “Video System” is set to “Auto”, you may not receive a clear picture due to signal differences. Should this occur, switch to the video system of the source signal.

6Setting the Video Setup

Selectable items

Description

0 IRE

Sets the black level to 0 IRE.

7.5 IRE

Sets the black level to 7.5 IRE.

Note

This function is available for the following signals.

With COMPONENT or COMPUTER/

COMPONENT input: - 480I

With S-VIDEO or VIDEO input: - NTSC3.58

-42

Image 44
Contents XV-Z17000 Special Note for Users in the U.K Introduction See bottom of projectorInformation Declaration of conformityUsing the Menu Screen Info Indicates safeguards for using the projectorContents Maintenance Maintenance Indicators Regarding the Lamp Reference AppendixCleaning AccessoriesPower-Cord Protection Damage Requiring ServiceDo not block the exhaust and intake vents Avoid locations with extremes of temperatureRest your eyes occasionally Using the projector in other countries Temperature monitor functionUsing the 3D Glasses Other connected equipmentOptional accessories AccessoriesSupplied accessories Part Names and Functions ProjectorProjector Rear View TerminalsRemote Control Using the Remote Control When using the remote controlInserting the Batteries Usable RangeQuick Start Place the projector facing a screenSelect the input mode Adjust the projector angle, focus and zoomTurn the power off Turn the video equipment on and start playbackSetting Up the Projector Setting Up the ProjectorStandard Setup Front Projection Example of standard setupProjection PRJ Mode Ceiling-mount SetupScreen Size and Projection Distance You may need other cables or connectors not listed below Samples of Cables for ConnectionConnecting to Video Equipment Connecting to Equipment with S-video Output TerminalConnecting to a Computer Connecting to a Computer Using the RGB CableFor details on RS-232C specifications and commands, see Controlling the Projector by a ComputerConnecting the Power Cord About the Lamp IndicatorDirect Power Off function Turning the Projector On/OffAdjusting the Projected Image Adjusting the FocusAdjusting the Picture Size Adjusting the HeightPress Keystone to enter the keystone mode Press P/R/O/Q to adjust Keystone CorrectionKeystone Correction Press KeystonePress P/R/O/Q to adjust Sphere Correction mode Press P/R/O/Q to adjust Rotation Correction modePress P/R to select SPHERE, and then press Enter  SphereSwitching the Input Mode Adjusting the Vertical Horizontal Position ImagePress Image Shift to enter the image shift mode Image ShiftAuto Sync Auto Sync Adjustment Selecting the Picture ModeDisplaying the Black Screen Temporarily Freezing a Moving ImageSwitching the Iris Setting Switching the Eco+Quiet ModeDisplaying an Enlarged Portion of an Image Hiding the Menu TemporarilyResize Mode Press Resize on the projector or on the remote controlResize Mode Resize buttonAbout Copyrights Menu Bar Items Picture menuUseful Features 3D Menu Press Menu Using the Menu ScreenMenu Selections Adjust- ments To adjust the projected image while viewing it You want to adjustPress or \ to adjust the item selected Press or to select the item2Adjusting the Image Picture Adjustment Picture Menu1Selecting the Picture Mode 3Switching the Iris Setting 7Adjusting the Colors5Using the Advanced 4Eco+QuietS. color adjustment screen 8Adjusting the Bright Boost 9Selecting the Film Mode0Setting Detail Enhancement EResetting All Adjustment ItemsComputer Image Adjustment SIG-ADJ Menu 1Adjusting the Computer Image2Setting the Resolution 3Auto Sync Auto Sync Adjustment6Setting the Video Setup 5Setting the Video System 7Adjusting the Dynamic Range8Signal Info Adjusting the Projected Image SCR-ADJ Menu 1Setting the Resize Mode2Adjusting the Image Position 3Adjusting the OverscanOr Q 5Keystone Mode Correction4Auto V-Keystone Correction 6Setting On-screen Display 7Setting the Brightness Menu Screen8Selecting the Background Image 9Selecting the Menu Screen PositionAdjusting the Projector Function PRJ-ADJ Menu 3Setting One Touch Play, System Standby and Input Name1Setting Auto Power Off Mode 2Setting the Power Save Mode Economy Mode4Setting the Demo Mode 6Fan Mode Setting7Returning to the Default Settings 8Lamp Timer LifePrecautions on using 3D Glasses Enjoying 3D Image ViewingAs you get more comfortable viewing 3D images  EpilepsySupplied Accessories for 3D Glasses Part NamesBefore Using the 3D Glasses Replacing the Button Cell BatteryClose the battery cover Insert the screw to secure the batUsing the 3D Glasses Attaching the Nose PadAttaching the 3D Glasses Band Usage Range of the 3D GlassesWhen 3D Auto Change is set to Yes When 3D Auto Change is set to NoViewing 3D Images Turn on the 3D Glasses and place them over your eyesPress 3D Menu Press P/R to select 3D Press O/Q to select On or OffPress P/R to select 3D Format, and then press Enter 3D Menu screen is displayed3D Settings 3D Menu Setting the 3D Format Menu 3D Format is set to Auto automatically Frame rate is changed3D Glasses lenses 3D Glasses infrared receiverSpecifications 3D Glasses Maintenance Cleaning the projectorCleaning the lens Cleaning the exhaust and intake ventsMaintenance Indicators About the temperature warning indicatorAbout the lamp indicator Indicators on the ProjectorNot illuminate Down Outlet, and then connect it again Replacing the Lamp Regarding the LampLamp Removing and Installing the Lamp Unit Remove the lamp unit coverResetting the Lamp Timer Connecting Pin Assignments Hdmi TerminalComputer Input Component InputRS-232C Specifications and Commands Computer controlCommands Computer Input Video Input Compatibility Chart ComputerDTV Troubleshooting Problem CheckReplace the lamp 3D images are not Switch to 3D mode For Sharp Assistance Specifications HdmiDimensions Units inches mmIndex Page Sharp Corporation
Related manuals
Manual 81 pages 27.87 Kb