Sharp 210T, 240T manual Regulatory Information, User Instructions, User Information

Page 29

regulat.fm Page 0 Monday, September 18, 2000 8:52 AM

Regulatory Information

FCC Information

User Instructions

The Federal Communications Commission Radio Frequency Interference Statement includes the following warning:

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television receptions, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

nReorient or relocate the receiving antenna.

nIncrease the separation between the equipment and receiver.

nConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.

nConsult the dealer or an experienced radio/TV technician for help.

User Information

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

If necessary, consult your dealer or an experienced radio/ television technician for additional suggestions. You may find the booklet called How to Identify and Resolve Radio/ TV Interference Problems helpful. This booklet was prepared by the Federal Communications Commission. It is available from the U.S. Government Printing Office, Washington, DC 20402, Stock Number 004-000-00345-4.

Warning

User must use shielded signal interface cables to maintain FCC compliance for the product.

Declaration of conformity for products Marked with FCC Logo

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause undesired operation.

The party responsible for product compliance:

SAMSUNG ELECTRONICS CO., LTD America QA Lab of Samsung

85 West Tasman Drive San Jose, CA 95134 USA Tel) 408-544-5124

Fax) 408-544-5191

Provided with this monitor is a detachable power supply cord with IEC320 style terminations. It may be suitable for connection to any UL Listed personal computer with similar configuration. Before making the connection, make sure the voltage rating of the computer convenience outlet is the same as the monitor and that the ampere rating of the computer convenience outlet is equal to or exceeds the monitor voltage rating.

For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration 5-15P type (parallel blades) plug cap. For 240 Volt applications use only UL Listed Detachable power supply cord with NEMA configuration 6-15P type (tandem blades) plug cap.

IC Compliance Notice

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations of ICES-003.

Cet appareil Numérique de classe B respecte toutes les exigences du Règlemont ICES-003 sur les équipements produisant des interférences au Canada.

MPR II Compliance

This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields.

European Notice

Products with the CE Marking comply with both the EMC Directive (89/336/EEC), (92/31/EEC), (93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community.

Compliance with these directives implies conformity to the following European Norms:

nEN55022:1998 – Radio Frequency Interference

nEN55024:1998 – Electromagnetic Immunity

nEN61000-3-2:1995 + A1 + A2 – Power Line Harmonics

nEN61000-3-3:1995 – Voltage Fluctuations

nEN60950 – Product Safety.

Portuguese Italiano Español Deutsch Français English

Image 29
Contents SyncMaster 210T SyncMaster 240T COVER.fm Page 2 Monday, September 18, 2000 843 AM Table of Contents Electric socket Monitor doing so may create the danger of electric shockTechnician should open the case of the LCD monitor Deutsch Français Unpacking Your MonitorKensington Security Slot Setting up Your LCD MonitorSetting up an Ergonomic Workstation Français English Connecting Your LCD MonitorSelf-Test Feature Check Stfc Installing the Video DriverPower Indicator Plug and PlayWarm-up Time Getting HelpUser Controls Adjusting Your LCD MonitorFunction Automatic SaveFunction Description Use this button to change a video sourceUse this button to optimize image quality automatically Follow these instructions to adjust the brightnessCoarse, and Image Position Use this button to change BrightnessFunction icons Function name Setting bar Tool TipAccessing the menu system Image Lock BrightnessContrast Color control PositionImage Size Sharpness Small window PC. Refer toSelects one OSD language out of six different languag- es Displayed side by side PBP OFF Disable PBP featureVideo Source 2 Super Video Signal S-Video Sync. Types and frequencies with polarities Resolution ExampleInformation Up Key By Remote-ControlLeft Key Appendix PowerSaverTroubleshooting Panel, Display, Settings Power Saver,Change the display settings Management system210T 240T SpecificationsPin Assignments Pin D-sub connectorDVI-D Connector Display Modes Preset timing modesNumerics IndexUser Information Regulatory InformationUser Instructions Germany