TANDBERG D1392602 manual Loadlimit Services Session, c xConfiguration IP Address, LoadLimit

Page 16

Loadlimit

TANDBERG Video Portal

Data port Command Interface User Guide

Loadlimit

Services

Session

SIP

•Gateway: Sets the gateway IP address. If a gateway is located on the LAN and the Video Portal needs to reach nodes through this gateway, the gateway address can be set using the gateway variable (the IP address of the gateway will be set automatically if the Video Portal is in DHCP mode)

•Domain Name: Sets the domain name string of which the gateway is part of. Minimum 0, maximum 64 characters.

Example of IP Address feedback:

*c xConfiguration IP Address: "127.0.0.1"

Sets the processor-load percentage at which calls should be routed to another Video Portal.

LoadLimit: <0..100>

Example of Loadlimit feedback: *c xConfiguration LoadLimit: 85

Displays all configured/uploaded .ivr-file services used in dial plans.

Services Service [1..64] Enabled: <On/Off>

Services Service [1..64] Name: <S: 0, 30>

Services Service [1..64] ServiceFile: <S: 0, 128>

Services Service [1..64] Logging: <On/Off> VP ONLY!!!!!!!!!!!!!

sub-commands:

•Enabled: <On/Off>: Enable the service.

•Name: <S: 0, 30>: Specifies the name of the service.

•ServiceFile: <S: 0, 128> Specifies which .ivr file is used as definition of this service.

•Logging: <On/Off>: Enables the service logging functionality.

Example of Service feedback:

*c xConfiguration Services Service 1 Enabled: On

*c xConfiguration Services Service 1 Name: "Direct Inwards Dialing"

*c xConfiguration Services Service 1 ServiceFile: "/tandberg/services/did.ivr"

*c xConfiguration Services Service 1 Logging: On

Sets a timeout time for sessions like telnet, ssh etc.

Session TimeOut: <0..65535>

Example of Session feedback:

*c xConfiguration Session TimeOut: 10000

Configures the SIP Proxy Mode and Address settings.

SIP Mode: <On/Off> or

SIP Interface Server Address <S: 0, 255> or

SIP Interface Server Type: <Auto/NortelMicrosoft/Cisco/Alcatel/Experimental>

D1392602

16

Image 16

Contents Software version V D1392602TANDBERG Video Portal Data port Command Interface User Guide Data port Command Interface User GuideTable of Contents 3. CONNECTING TO THE DATA PORT COMMAND INTERFACE USING TELNET4. THE TANDBERG VIDEO PORTAL COMMANDS Command format1. Introduction 2.2. Troubleshooting 2.1. Hardware and CablingTANDBERG V IDEO P ORTAL DCE, 9 pinIf communication cannot be established between the PC/terminal and the TANDBERG Video Portal’s Data port the following should be checked 3. Connecting to the Data port Command Interface using Telnet 4. The TANDBERG Video Portal Commands 4.1.1. Command formatNOTE! The Data port Command Interface is not case sensitive 4.1.2. Command typesXconf telnet mode on 4.2. The commandsXconf telnet mode 4.2.1. System Configuration Commands Command alplanDialplan Entry 1..64 Enabled On/Off Dialplan Entry 1..64 Name S 0 Dialplan Entry 1..64 ServiceIddistinguished c xConfiguration Dialplan Entry 1 Prefix c xConfiguration Dialplan Entry 2 Property 2 Name avmode c xConfiguration Dialplan Entry 4 Prefix Ethernet H323CallSetup H323Gatekeeper NOTE! The Video Portal needs to reboot before the changes will applyH323CallSetup Mode Direct/Gatekeeper H323Gatekeeper Authentication Mode Auto/Off orXconf H323Gatekeeper Authentication c xConfiguration H323Gatekeeper Authentication Mode Offc xConfiguration H323Gatekeeper Authentication ID NOTE! Changes become effective after rebootLoadlimit Services Session c xConfiguration IP AddressServices Service 1..64 Enabled On/Off Services Service 1..64 Name S 0 Services Service 1..64 ServiceFile S 0SIP Interface Transport Default TCP/UDP/TLS c xConfiguration SIP Mode Onc xConfiguration SIP Interface Server Address c xConfiguration SIP Interface Server Type Autoc xConfiguration SNMP SystemContact c xConfiguration SNMP SystemLocationc xConfiguration SNMP HostIPAddr 1 c xConfiguration SNMP HostIPAddr 2 c xConfiguration SNMP HostIPAddr 34.2.2. General Video Portal Commands Command ExternalManager NTP Optionsc xConfiguration ExternalManager Address c xConfiguration Options 1 Key 115201SS7-1-55C3EBB74.2.3. System Status Commands Command Dialplan DiskExample DiskEthernet ExternalManager Feedback 1 EthernetMacAddress Speed MacAddress 000E0C5CB57D Speed 100full *s/endH323Gatekeeper IP H323GatekeeperStatus Address Port Address Port 1719 *s/endAddress Port Last Update Last Correction NTP OptionsName Address SubnetMask Gateway 10.31.0.1 DNS ServerService SystemLoad SystemUnit ServiceOptions SystemLoadConfiguration Telephony VideoTelephony Configuration Telephony VideoTelephony Hardware Version EPProductType Uptime Software Version Name ReleaseDate PRI TemperatureCelcius TemperatureFahrenheit4.2.4. Debug Commands 4.2.5. Special Xcommand CommandsCommand Syslog Level Mask VolumeDefaultValuesSet Level 1 CheckDisk ClearDialplanEntries ClearServiceEntries DefaultValuesSetExample restore all default factory setting xCommand DefaultValuesSet Dial DialplanEntryDelete DialplanEntrySwap DisconnectCall ParametersOK Result parameter Session ID S 1 Example Parameter DialplanEntryNumber ExampleOK Result parameters ID 1 ERROR Result parameters ID 1 ERROR Result parametersEraseDisk FeedbackDeregister FeedbackRegister Expression 1 .. 15 S 0, 256 XPath expression OK Result parametersOptionKeyAdd OptionKeyDelete RestoreDefaultServices ServiceEntryDeleteExample Delete Option Key nr. 1 xCommand OptionKeyDelete Parameters ServiceEntryNumberrServiceEntrySwap Example Delete Service nr. 10 xCommand ServiceEntryDeleteParameters ServiceEntryNumberr ServiceEntryNumber2r Example Swap Service nr. 10General User Commands About Help or ? Licence Relkey Xfeedbackhelp Licensexhistory ? XhistoryExamples xhistory call