TANDBERG D1392602 manual EraseDisk FeedbackDeregister FeedbackRegister, Example, Parameters

Page 29

EraseDisk

TANDBERG Video Portal

Data port Command Interface User Guide

EraseDisk

FeedbackDeregister

FeedbackRegister

Example:

xCommand DisconnectCall ABCD123456

*r Result (status=OK): *r/end

OK

This command wipes all the data from the internal harddisk

Example:

xCommand EraseDisk

*r Result (status=OK): *r/end

OK

Command used to deregister XML feedback over HTTP(S).

Parameters:

•ID: <1 .. 3> ID for the registration to deregister.

OK Result parameters:

•ID: <1 .. 3>

ERROR Result parameters:

•Cause: <1…> Cause code specifying why the command was not accepted by the system

•Description Textual description of the cause code.

Example:

xCommand feedbackderegister id:1 *r Result (status=OK):

ID: 2 *r/end

OK

Command used to instruct the system to return XML feedback over HTTP(S) to specific URLs. What parts of the Status and Configuration XML documents to monitor are specified by XPath expressions. The system supports issuing feedback to 3 different URLs. The system allows a total of 20 XPath expressions to be registered, with a maximum of 15 for a single URL.

Parameters:

•ID: <1 .. 3> ID for the registration. If this parameter is omitted the system uses the first vacant ID.

•URL(r): <S: 0, 256> The URL to post feedback to.

•Expression: 1 .. 15: <S: 0, 256> XPath expression

OK Result parameters:

•ID: <1 .. 3>

ERROR Result parameters:

D1392602

29

Image 29

Contents D1392602 Software version VTANDBERG Video Portal Data port Command Interface User Guide Data port Command Interface User Guide3. CONNECTING TO THE DATA PORT COMMAND INTERFACE USING TELNET Table of Contents4. THE TANDBERG VIDEO PORTAL COMMANDS Command format1. Introduction 2.1. Hardware and Cabling 2.2. TroubleshootingTANDBERG V IDEO P ORTAL DCE, 9 pinIf communication cannot be established between the PC/terminal and the TANDBERG Video Portal’s Data port the following should be checked 3. Connecting to the Data port Command Interface using Telnet 4.1.1. Command format 4. The TANDBERG Video Portal CommandsNOTE! The Data port Command Interface is not case sensitive 4.1.2. Command typesXconf telnet mode 4.2. The commandsXconf telnet mode on Command alplan 4.2.1. System Configuration CommandsDialplan Entry 1..64 Enabled On/Off Dialplan Entry 1..64 Name S 0 Dialplan Entry 1..64 ServiceIddistinguished c xConfiguration Dialplan Entry 1 Prefix c xConfiguration Dialplan Entry 2 Property 2 Name avmode c xConfiguration Dialplan Entry 4 Prefix NOTE! The Video Portal needs to reboot before the changes will apply Ethernet H323CallSetup H323GatekeeperH323CallSetup Mode Direct/Gatekeeper H323Gatekeeper Authentication Mode Auto/Off orc xConfiguration H323Gatekeeper Authentication Mode Off Xconf H323Gatekeeper Authenticationc xConfiguration H323Gatekeeper Authentication ID NOTE! Changes become effective after rebootc xConfiguration IP Address Loadlimit Services SessionServices Service 1..64 Enabled On/Off Services Service 1..64 Name S 0 Services Service 1..64 ServiceFile S 0c xConfiguration SIP Mode On SIP Interface Transport Default TCP/UDP/TLSc xConfiguration SIP Interface Server Address c xConfiguration SIP Interface Server Type Autoc xConfiguration SNMP SystemLocation c xConfiguration SNMP SystemContactc xConfiguration SNMP HostIPAddr 1 c xConfiguration SNMP HostIPAddr 2 c xConfiguration SNMP HostIPAddr 3Command ExternalManager NTP Options 4.2.2. General Video Portal Commandsc xConfiguration ExternalManager Address c xConfiguration Options 1 Key 115201SS7-1-55C3EBB7Command Dialplan Disk 4.2.3. System Status CommandsExample DiskEthernet Ethernet ExternalManager Feedback 1MacAddress Speed MacAddress 000E0C5CB57D Speed 100full *s/endH323Gatekeeper H323Gatekeeper IPStatus Address Port Address Port 1719 *s/endNTP Options Address Port Last Update Last CorrectionName Address SubnetMask Gateway 10.31.0.1 DNS ServerService Service SystemLoad SystemUnitOptions SystemLoadConfiguration Telephony VideoTelephony Hardware Version EP Configuration Telephony VideoTelephonyProductType Uptime Software Version Name ReleaseDate PRI TemperatureCelcius TemperatureFahrenheit4.2.5. Special Xcommand Commands 4.2.4. Debug CommandsCommand Syslog Level Mask VolumeExample restore all default factory setting xCommand DefaultValuesSet CheckDisk ClearDialplanEntries ClearServiceEntries DefaultValuesSetDefaultValuesSet Level 1 Parameters Dial DialplanEntryDelete DialplanEntrySwap DisconnectCallOK Result parameter Session ID S 1 Example Parameter DialplanEntryNumber ExampleID 1 ERROR Result parameters OK Result parameters ID 1 ERROR Result parametersEraseDisk FeedbackDeregister FeedbackRegister Expression 1 .. 15 S 0, 256 XPath expression OK Result parametersServiceEntryDelete OptionKeyAdd OptionKeyDelete RestoreDefaultServicesExample Delete Option Key nr. 1 xCommand OptionKeyDelete Parameters ServiceEntryNumberrExample Delete Service nr. 10 xCommand ServiceEntryDelete ServiceEntrySwapParameters ServiceEntryNumberr ServiceEntryNumber2r Example Swap Service nr. 10About Help or ? Licence Relkey Xfeedback General User Commandshelp LicenseExamples xhistory call Xhistoryxhistory ?