TANDBERG D1392602 manual H323Gatekeeper IP, Status Address Port, Address Port 1719 *s/end

Page 22

TANDBERG Video Portal

Data port Command Interface User Guide

H323Gatekeeper

Expression: ""

Expression: "" *s/end

Displays the status of the connection with the gatekeeper.

H323Gatekeeper

Status format:

<Status>

<Port>

---

Parameters:

•Status, indicates whether the Video Portal is registered with the gatekeeper

•Address, the IP address of the connected gatekeeper

•Port, the gatekeeper port the Video Portal is connected with

Example of H323Gatekeeper feedback: *s H323Gatekeeper (status=Registered):

Address: "10.47.9.1"

Port: 1719 *s/end

Displays the IP configuration of the Video Portal

Status format:

<Address>

<DNS:

Server 1: Address>

Server 2: Address>

Server 3: Address>

Server 4: Address>

Server 5: Address>

Domain:

D1392602

Image 22

Contents TANDBERG Video Portal Data port Command Interface User Guide Software version VD1392602 Data port Command Interface User Guide4. THE TANDBERG VIDEO PORTAL COMMANDS Table of Contents3. CONNECTING TO THE DATA PORT COMMAND INTERFACE USING TELNET Command format1. Introduction TANDBERG V IDEO P ORTAL 2.2. Troubleshooting2.1. Hardware and Cabling DCE, 9 pinIf communication cannot be established between the PC/terminal and the TANDBERG Video Portal’s Data port the following should be checked 3. Connecting to the Data port Command Interface using Telnet NOTE! The Data port Command Interface is not case sensitive 4. The TANDBERG Video Portal Commands4.1.1. Command format 4.1.2. Command typesXconf telnet mode on 4.2. The commandsXconf telnet mode Dialplan Entry 1..64 Enabled On/Off Dialplan Entry 1..64 Name S 0 4.2.1. System Configuration CommandsCommand alplan Dialplan Entry 1..64 ServiceIddistinguished c xConfiguration Dialplan Entry 1 Prefix c xConfiguration Dialplan Entry 2 Property 2 Name avmode c xConfiguration Dialplan Entry 4 Prefix H323CallSetup Mode Direct/Gatekeeper Ethernet H323CallSetup H323GatekeeperNOTE! The Video Portal needs to reboot before the changes will apply H323Gatekeeper Authentication Mode Auto/Off orc xConfiguration H323Gatekeeper Authentication ID Xconf H323Gatekeeper Authenticationc xConfiguration H323Gatekeeper Authentication Mode Off NOTE! Changes become effective after rebootServices Service 1..64 Enabled On/Off Services Service 1..64 Name S 0 Loadlimit Services Sessionc xConfiguration IP Address Services Service 1..64 ServiceFile S 0c xConfiguration SIP Interface Server Address SIP Interface Transport Default TCP/UDP/TLSc xConfiguration SIP Mode On c xConfiguration SIP Interface Server Type Autoc xConfiguration SNMP HostIPAddr 1 c xConfiguration SNMP HostIPAddr 2 c xConfiguration SNMP SystemContactc xConfiguration SNMP SystemLocation c xConfiguration SNMP HostIPAddr 3c xConfiguration ExternalManager Address 4.2.2. General Video Portal CommandsCommand ExternalManager NTP Options c xConfiguration Options 1 Key 115201SS7-1-55C3EBB7Example 4.2.3. System Status CommandsCommand Dialplan Disk DiskMacAddress Speed Ethernet ExternalManager Feedback 1Ethernet MacAddress 000E0C5CB57D Speed 100full *s/endStatus Address Port H323Gatekeeper IPH323Gatekeeper Address Port 1719 *s/endName Address Port Last Update Last CorrectionNTP Options Address SubnetMask Gateway 10.31.0.1 DNS ServerOptions Service SystemLoad SystemUnitService SystemLoadProductType Uptime Software Version Name ReleaseDate Configuration Telephony VideoTelephonyConfiguration Telephony VideoTelephony Hardware Version EP PRI TemperatureCelcius TemperatureFahrenheitCommand 4.2.4. Debug Commands4.2.5. Special Xcommand Commands Syslog Level Mask VolumeDefaultValuesSet Level 1 CheckDisk ClearDialplanEntries ClearServiceEntries DefaultValuesSetExample restore all default factory setting xCommand DefaultValuesSet OK Result parameter Session ID S 1 Example Dial DialplanEntryDelete DialplanEntrySwap DisconnectCallParameters Parameter DialplanEntryNumber ExampleEraseDisk FeedbackDeregister FeedbackRegister OK Result parameters ID 1 ERROR Result parametersID 1 ERROR Result parameters Expression 1 .. 15 S 0, 256 XPath expression OK Result parametersExample Delete Option Key nr. 1 xCommand OptionKeyDelete OptionKeyAdd OptionKeyDelete RestoreDefaultServicesServiceEntryDelete Parameters ServiceEntryNumberrParameters ServiceEntryNumberr ServiceEntryNumber2r ServiceEntrySwapExample Delete Service nr. 10 xCommand ServiceEntryDelete Example Swap Service nr. 10help General User CommandsAbout Help or ? Licence Relkey Xfeedback Licensexhistory ? XhistoryExamples xhistory call