Sharp XR-50S, XR-55X appendix Turning the Projector On/Off, Power indicator Lamp indicator

Page 29

Turning the Projector On/Off

Turning the Projector On

Note that the connections to external equipment and power outlet should be done before performing the operations written below. (See pages 21 to 24.)

Open the lens shutter fully and press STANDBY/ON on the projector or ON on the remote control.

•The power indicator illuminates green.

•After the lamp indicator illuminates, the projector is ready to start operation.

Note

•About the Lamp Indicator

The lamp indicator illuminates to indicate the status of the lamp.

Green: The lamp is on.

Blinking in green: The lamp is warming up.

Red: The lamp is shut down abnormally or the lamp should be replaced.

•When switching on the projector, a slight

ﬂ ickering of the image may be experienced within the ﬁ rst minute after the lamp has been illuminated. This is normal operation as the lamp's control circuitry is stabilising the lamp output characteristics. It should not be regarded as faulty operation.

•If the projector is put into Standby mode and immediately turned on again, the lamp may take some time to start projection.

•When System Lock is set, the keycode input box appears. To cancel the keycode setting, input the keycode that you have already set. See page 50 for details.

Info

•When “Auto Restart” is set to “On”:

If the power cord is unplugged from the outlet or the breaker switch is turned off when the projector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on. (See page 49.)

•English is the factory default language. If you want to change the on-screen display to another language, change the language according to the procedure on page 48.

Power indicator Lamp indicator

STANDBY/ON button

STANDBY button

ON button

On-screen display (conﬁrmation message)

Basic Operation

Turning the Power Off (Putting the Projector into Standby Mode)

Press STANDBY/ON on the projector or STANDBY on the remote control, then press that button again while the conﬁrmation message is displayed, to put the projector into Standby mode.

• The projector cannot be turned on while cooling.

Info

•Direct Power Off function:

You can unplug the power cord from the AC outlet even if the cooling fan is still running.

25

Image 29

Contents XR-55X XR-50S Model No Serial No Only This Apparatus Must be EarthedIf YOU have ANY DOUBT, Consult a Qualified Electrician Page Void the users authority to operate this equipment IntroductionENGLISHSharp Electronics Corporation Sharp PROJECTOR, Model XR-55X/XR-50SSharp Plaza, Mahwah, New Jersey TEL 1-800-BE-SHARP A. onlyFor Future Reference Maintenance Troubleshooting IndexContents Reference Adjusting the Projector Function PRJ-ADJ1/2 MenuPower Sources CleaningAccessories Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check OverloadingDo not block the exhaust and intake vents Avoid locations with extremes of temperatureRest your eyes occasionally Other connected equipment Using the projector in other countriesTemperature monitor function Page Optional accessories AccessoriesFront View Part Names and FunctionsRear View Terminals Stereoscopic 3D Projection Usable Range Remote control signal transmittersInserting the Batteries STANDBY/ON Setup and ProjectionEasy Start On the remote Control Turn the computer on Turn the power offStandard Setup Front Projection Setting Up the ProjectorSetting Up the Projector Signal Input 169 Mode Signal Input Normal ModeScreen Size and Projection Distance Screen Lens centerCeiling-Mount Setup Projection PRJ ModeTerminals on the Projector Connecting the Projector to Other EquipmentConnecting the Projector to Other Equipment Monitor OUT Controlling the Projector by a Computer Connecting the Power CordAC socket Power cord To AC outlet supplied Turning the Projector On Power indicator Lamp indicatorTurning the Projector On/Off Adjusting the Projected Image Adjusting the Focus About the Setup GuidePress Enter to exit the Setup Guide screen Image ProjectionAdjusting the Picture Size Adjusting the HeightUse the rear adjustment foot to make the projector level Make small adjustments Height Adjust leverOn-screen display Keystone Correction mode Adjustment buttons P/R/O/Q Return button Keystone buttonCorrecting Trapezoidal Distortion Press KeystoneInput buttons AV Mute button VOL +/- Volume buttons Buttons Switching the Input ModeAdjusting the Volume Resize Resize ModePress Resize About Copyrights Displaying and Setting the Break Timer Operating with the Remote ControlUsing the Spot Function Switching the Eco+Quiet ModeSelecting the Picture Mode Auto Sync Auto Sync AdjustmentFreezing a Moving Image Displaying an Enlarged Portion of an ImageWhen moving the cursor Using the Remote Control as the Wireless Computer MouseWhen left-clicking When right-clickingPicture menu Menu ItemsCOMPUTER/COMPONENT Projector adjustment PRJ-ADJ1/2 menu Menu Selections Quick Start Menu Using the Menu ScreenPress Menu ExampleQuick Start Menu Example Adjusting BrightMenu Selections Complete Menu Following items can be conﬁgured on the Quick Start MenuImage while watching it To adjust the projectedSelecting the Picture Mode Picture Adjustment Picture MenuPAGE1 Menu operation nAdjusting the Color Temperature Adjusting the ImageAdjusting the Colors Adjusting Hue, Saturation, or ValueReducing Image Noise DNR Selecting the Film ModeEco+Quiet Resolution Setting Signal Adjustment SIG-ADJ MenuSignal Type Setting When reproducing Ntsc signals in PAL video equipment Setting the Video SetupSetting the Resize Mode Adjusting the Projected Image SCR-ADJ MenuAdjusting the Image Position Keystone CorrectionSetting the On-screen Display Setting the OverscanClosed Caption For Americas onlySelecting the Background Image Selecting the Setup GuideReversing/Inverting Projected Images Selecting the Wall ColorAuto Power Off Function Auto Sync Auto Sync AdjustmentSpeaker Setting Auto Restart FunctionSystem Lock Function Adjusting the Projector Function PRJ-ADJ1/2 MenuFan Mode Setting Keylock Function Setting the Function Button OperationSelecting the Quick Start Menu Select On, then press EnterChecking the Lamp Life Status Standby ModeCleaning the projector MaintenanceAbout the temperature warning indicator Maintenance IndicatorsAbnormally high Are high Lower than 95F +35ºC Lamp Regarding the LampReplacing the Lamp A onlyRemove the lamp unit cover Removing and Installing the Lamp UnitLamp unit AN-D350LPResetting the Lamp Timer COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Connecting Pin AssignmentsUSB Terminal Type B USB connector Computer control RS-232C Speciﬁcations and CommandsCommunication conditions Basic formatComputer Projector CommandsRGB PAL CC1 Computer Computer Compatibility Chart21-24 Troubleshooting53, 54 Sharp Electronics Corporation Speciﬁcations Dimensions Index Kensington Security Standard connector ·················13SHAR~

Related manuals

Manual 78 pages 580 b