Sharp XR-50S, XR-55X Removing and Installing the Lamp Unit, Remove the lamp unit cover, Lamp unit

Page 61

Removing and Installing the Lamp Unit

Warning!

•Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury.

Optional	Lamp unit
accessory	AN-D350LP
	AN-D350LP

Info

•Do not touch the glass surface of the lamp unit or the inside of the projector.

•To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below.

•Do not loosen other screws except for the lamp unit cover and lamp unit.

1Press STANDBY/ON on the projector or STANDBY on the remote control to put the projector into Standby mode.

2 Disconnect the power cord.

•Unplug the power cord from the AC socket.

•Leave the lamp until it has fully cooled down (about 1 hour).

3 Remove the lamp unit cover.

•Close the lens shutter and turn the

projector over. Loosen the user service screw (1) that secures the lamp unit cover. Remove the lamp unit cover (2).

STANDBY/ON button

AC socket

User service screw (for lamp unit cover)

Appendix

57

Image 61

Contents XR-55X XR-50S Model No Serial No If YOU have ANY DOUBT, Consult a Qualified Electrician This Apparatus Must be EarthedOnly Page Void the users authority to operate this equipment IntroductionENGLISHSharp Electronics Corporation Sharp PROJECTOR, Model XR-55X/XR-50SSharp Plaza, Mahwah, New Jersey TEL 1-800-BE-SHARP A. onlyFor Future Reference Maintenance Troubleshooting IndexContents Reference Adjusting the Projector Function PRJ-ADJ1/2 MenuPower Sources CleaningAccessories Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check OverloadingRest your eyes occasionally Avoid locations with extremes of temperatureDo not block the exhaust and intake vents Temperature monitor function Using the projector in other countriesOther connected equipment Page Optional accessories AccessoriesFront View Part Names and FunctionsRear View Terminals Stereoscopic 3D Projection Inserting the Batteries Remote control signal transmittersUsable Range Easy Start Setup and ProjectionSTANDBY/ON On the remote Control Turn the computer on Turn the power offSetting Up the Projector Setting Up the ProjectorStandard Setup Front Projection Signal Input 169 Mode Signal Input Normal ModeScreen Size and Projection Distance Screen Lens centerCeiling-Mount Setup Projection PRJ ModeTerminals on the Projector Connecting the Projector to Other EquipmentConnecting the Projector to Other Equipment Monitor OUT AC socket Power cord To AC outlet supplied Connecting the Power CordControlling the Projector by a Computer Turning the Projector On/Off Power indicator Lamp indicatorTurning the Projector On Adjusting the Projected Image Adjusting the Focus About the Setup GuidePress Enter to exit the Setup Guide screen Image ProjectionAdjusting the Picture Size Adjusting the HeightUse the rear adjustment foot to make the projector level Make small adjustments Height Adjust leverOn-screen display Keystone Correction mode Adjustment buttons P/R/O/Q Return button Keystone buttonCorrecting Trapezoidal Distortion Press KeystoneAdjusting the Volume Switching the Input ModeInput buttons AV Mute button VOL +/- Volume buttons Buttons Press Resize Resize ModeResize About Copyrights Displaying and Setting the Break Timer Operating with the Remote ControlUsing the Spot Function Switching the Eco+Quiet ModeSelecting the Picture Mode Auto Sync Auto Sync AdjustmentFreezing a Moving Image Displaying an Enlarged Portion of an ImageWhen moving the cursor Using the Remote Control as the Wireless Computer MouseWhen left-clicking When right-clickingPicture menu Menu ItemsCOMPUTER/COMPONENT Projector adjustment PRJ-ADJ1/2 menu Menu Selections Quick Start Menu Using the Menu ScreenPress Menu ExampleQuick Start Menu Example Adjusting BrightMenu Selections Complete Menu Following items can be conﬁgured on the Quick Start MenuImage while watching it To adjust the projectedSelecting the Picture Mode Picture Adjustment Picture MenuPAGE1 Menu operation nAdjusting the Color Temperature Adjusting the ImageAdjusting the Colors Adjusting Hue, Saturation, or ValueEco+Quiet Selecting the Film ModeReducing Image Noise DNR Signal Type Setting Signal Adjustment SIG-ADJ MenuResolution Setting When reproducing Ntsc signals in PAL video equipment Setting the Video SetupSetting the Resize Mode Adjusting the Projected Image SCR-ADJ MenuAdjusting the Image Position Keystone CorrectionSetting the On-screen Display Setting the OverscanClosed Caption For Americas onlySelecting the Background Image Selecting the Setup GuideReversing/Inverting Projected Images Selecting the Wall ColorAuto Power Off Function Auto Sync Auto Sync AdjustmentSpeaker Setting Auto Restart FunctionFan Mode Setting Adjusting the Projector Function PRJ-ADJ1/2 MenuSystem Lock Function Keylock Function Setting the Function Button OperationSelecting the Quick Start Menu Select On, then press EnterChecking the Lamp Life Status Standby ModeCleaning the projector MaintenanceAbout the temperature warning indicator Maintenance IndicatorsAbnormally high Are high Lower than 95F +35ºC Lamp Regarding the LampReplacing the Lamp A onlyRemove the lamp unit cover Removing and Installing the Lamp UnitLamp unit AN-D350LPResetting the Lamp Timer COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Connecting Pin AssignmentsUSB Terminal Type B USB connector Computer control RS-232C Speciﬁcations and CommandsCommunication conditions Basic formatComputer Projector CommandsRGB PAL CC1 Computer Computer Compatibility Chart21-24 Troubleshooting53, 54 Sharp Electronics Corporation Speciﬁcations Dimensions Index Kensington Security Standard connector ·················13SHAR~

Related manuals

Manual 78 pages 580 b