Helpful Functions Set during Installation (“PRJ” menu)
|
| Picture Audio | SIG | SCR |
| PRJ |
| Net. |
| Auto Power Off |
|
| On |
| |||
|
|
|
| |||||
| Auto Restart |
|
| On |
| |||
|
|
|
| |||||
| COMPUTER2 Select |
|
| Monitor Output |
| |||
|
|
|
| |||||
| STANDBY Mode |
|
| Standard |
| |||
|
|
|
| |||||
|
|
| 9600bps |
| ||||
|
|
|
| |||||
| Fan Mode |
|
| Normal |
| |||
|
|
|
| |||||
| Sysem Lock |
|
| Disable |
| |||
|
|
|
| |||||
| DLP® Link™ |
|
| Off |
| |||
|
|
|
|
DLP® Link™ Invert Memory Menu
T |
|
| Rotate Indicator |
| On |
|
|
| |||
Z |
|
| All reset |
|
|
|
|
|
| ||
H |
|
|
|
| |
| Lamp Timer (Life) | [ | 0]h [ 0] min ( 100%) | ||
| |||||
|
|
|
|
|
|
|
|
| SEL./ADJ. |
| ENTER |
|
|
| RETURN |
| END |
1 Auto Power Off Function
Selectable | Description | |
items | ||
| ||
|
| |
On | The projector automatically enters | |
| the standby mode when no input | |
| signal is detected for 15 minutes or | |
| longer. | |
Off | The Auto Power Off function will | |
| be disabled. |
Note
•When the Auto Power Off function is set to “On”, 5 minutes before the projector enters the standby mode, the message “Enter STANDBY mode in X min.” will appear on the screen to indicate the remaining minutes.
2 Auto Restart Function
Selectable | Description | |
items | ||
| ||
|
| |
On | If the power cord is unplugged | |
| from the outlet or the breaker | |
| switch is turned off when the | |
| projector is on, then the projector | |
| automatically turns on when the | |
| power cord is plugged into the AC | |
| outlet or the breaker switch is | |
| turned on. | |
Off | The projector does not turn on | |
| automatically when the power | |
| cord is plugged into the AC outlet | |
| or the breaker switch is turned on. |
Menu operation n Page 46
3COMPUTER2 Select
You can also use the MONITOR OUT terminal as the COMPUTER/COMPONENT 2 terminal. Select whether to use the terminal as an input terminal or output terminal.
Selectable items | Description |
|
|
Input | The terminal can be used as an |
| input terminal (COMPUTER/ |
| COMPONENT 2). |
Monitor Output | The terminal can be used as an |
| output terminal (MONITOR OUT). |
Note
•Set this before connecting the external equipment.
•The setting cannot be changed when Input mode is “COMPUTER 2”.
4STANDBY Mode
When set to “Eco”, power consumption is reduced in Standby mode.
Selectable items | Description |
Eco | The monitor output, |
| Network functions are switched off in |
| Standby mode. |
Standard | The monitor output, |
| Network functions are activated even |
| if the projector is in Standby mode. |
5Selecting the Transmission
Speed (RS-232C)
Make sure that both the projector and com- puter are set for the same baud rate.
Selectable items | Description | |
|
|
|
9600 bps | Transmission speed is slow. | |
38400 bps |
|
|
|
| |
115200 bps | Transmission speed is rapid. |
Note
•Refer to the “SETUP MANUAL” contained on the supplied
•Refer to the computer’s operation manual for instructions for setting the computer’s baud rate.
56