Runco VX-33D operation manual Installation

Page 60

Installation

Adjusting the Height (Y): With the white field still on-screen, loosen the Height/Y Adjustment T-Screws on either side of the lens. Then, slowly move the anamorphic lens into place so that there are no shadows on the top or bottom of the screen:

Too Low

Correct position

Too High

When the height is properly set, tighten the Height Adjustment T-Screws to secure the lens in place.

Pitch (Angle): Next, angle the lens to even out any top-to-bottom pincushion distortion. To do this, loosen the Pitch Adjustment T-Screws (directly below the Height/Y Adjustment T-Screws) on either side of the lens to allow it to pivot freely. Then, adjust the anamorphic lens angle so that the projected image is rectangular:

Correct Lens Angle

Incorrect Lens Angle

The anamorphic lens will almost always be angled with respect to the projector; this is normal.

Once the proper lens angle has been set, firmly tighten the Pitch Adjustment T-Screws to secure the lens in place.

There may be some pincushion distortion even after the lens is

Note properly adjusted, especially at shorter throw distances. If this is the case, Runco recommends that you slightly over-scan the image into the screen frame area to mask the distortion.

44	Runco VX-33d Installation/Operation Manual

Image 60

Contents VX-33d Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Maintenance and Troubleshooting OperationSpecifications Serial CommunicationsTable of Contents Xiv List of Figures List of Figures Xvi Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions VX-33d at a GlanceVX-33d Rear Panel VX-33d Rear PanelPower Input 100 to 240 VAC Connect the VX-33d to power here USB-BDVI-DL Dual-Link DHD Controller Front Panel DHD Controller Front PanelIssue LED Service only For future use DHD Controller Rear PanelDVI-DL DUAL-LINK Output 1080p RS-232/485 Control PortVolt 750 mA Trigger Outputs Hdmi I 1 / Hdmi II 2 DigitalVX-33d Remote Control VX-33d Remote ControlPicture Adjustment Buttons BRT Brightness On / OFFSource Selection Buttons VID S-VideoMemory Preset Buttons Aspect Ratio Selection Buttons169 Lbox LetterboxInstallation Remote ControlQuick Setup Installation OverviewStep Procedure For Details, Refer to If installing a VX-33d/CineWide or VX-33d/CineWideInstallation Considerations Projector Installation OptionsInstallation Type Ambient LightVX-33d Lens Options and Throw Ratios Ceiling Installation Floor InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only VX-33d Vertical and Horizontal Lens Shift Limits Folded OpticsInstalling the Primary Projection Lens Other ConsiderationsInstallation Installing the Optional CineWide Lens Mount Installing the AutoScope Lens Motor VX-33d/CineWide with AutoScopeRemove VX-33d with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Mounting the VX-33d Floor Mounting Upright Ceiling Mounting InvertedAdjusting the Projection Connections to the VX-33d and DHD ControllerAngle 10. Connecting the VX-33d to the DHD Controller Connecting Source Components to the DHD Controller Hdmi Connections See FigureHdmi Source HD-DVD/BD/DVD Player or HD Tuner with 12. Digital DTV RGB or Component Video Connections HD1, HD2 13. Digital DTV RGB or Component Video Connections HD3 Analog Computer RGB Connections See Figure 14. Analog RGB ConnectionsVideo/Composite Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcRS-232 Controller Connection17 -volt Trigger Output Connections Connecting an External IR To a 200-240 VAC power sourceReceiver to the DHD Input voltage to the AutoScope lens motor must be betweenTurning on the Power Adjusting the Picture OrientationAdjustments Primary LensFocus ZoomInstalling and Adjusting the CineWide Anamorphic Lens It is extremely important that the primary lens is properly20. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Wrong PositionUsing the On-Screen Menus OperationMemory Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio Aspect Ratio Settings Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Hdtv programs in theirPicture Remote Aspect Ratio Control Description KeyPicture Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionMemory Presets Memory PresetsInformation InformationCalibration Calibration ISF NightISF Day Gain/Offset Refer to ISF Night Display Color, above Service ServiceHD Format ISF Day/Night presets Maintenance and Troubleshooting Lamp ReplacementFilter Replacement Side Filter Access PanelTroubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Maintenance and Troubleshooting If you are using a PC to communicate with the DHD Controller Serial CommunicationsSerial Commands Command Description ResponseInput Selection Commands Aspect Ratio CommandsCommand Description Response Image Preset Commands Menu Navigation CommandsPicture Adjust Commands Enter or Select buttonCommand Description Response Status Commands Status============================== Resolution 720P60 Serial Communications Specifications VX-33d SpecificationsVX-33d Specifications Home Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsDHD Controller Specifications DHD Controller SpecificationsVX-33d Dimensions 1shows the VX-33d dimensions all dimensions are in inchesSupported Signal Timings by Input Supported TimingsPAL-B/G Page 020-1004-00 rev. a September