Runco VX-2000d manual You must enter a passcode to access the Calibration menu

Page 59

Operation

Use the Calibration menu to perform advanced picture quality adjustments. This menu should be used by ISF-certified technicians only.

You must enter a passcode to access the Calibration menu.

Note

To recall the ISF Night or ISF Day settings, do one of the following:

•Select “ISF Night” or “ISF Day” from the ISF Presets menu (see above);

•Press ISF NIGHT or ISF DAY on the remote control; or

•From this menu, choose Display Color, Input Image or Input Color for the preset you want to recall.

ISF Night - Display Color: Use the Display Color settings to change the characteristics of the output signal. These settings are global (independent of any particular input).

•Gain: Use the Gain controls to correct color imbalances in the bright areas of the image. A good way to do this is to use a test pattern consisting mostly of solid white areas, such as an 80 IRE “window” pattern. If the white areas contain traces of red, green or blue, decrease the Gain for that color.

•Gamma/Offset: Use the Gamma and Offset controls in the White Balance sub-menu to correct color imbalances in the dark areas of the image.

A good way to do this is to use a test pattern consisting mostly of dark gray areas, such as a 30 IRE “window” pattern. If the gray areas contain traces of red, green or blue, decrease the Gamma or Offset for that color.

Tip

Adjust Gamma before Offset. Gamma provides coarse adjustment of

low-lights; Offset provides finer adjustment.

•Iris: Select Iris from the Display Color Menu to increase or decrease the Reflectance Volume Regulation setting. RVR lets you control the aperture or iris size (the physical opening through the lens; similar to an “f-stop” on a camera). Doing so allows you to optimize brightness and contrast according to the amount of ambient light in the viewing area.

Use a lower setting (0 or 1) for rooms with lots of ambient light. Use the higher setting

(2) for more “theater-like” viewing conditions (little or no ambient light).

•Color Temp: Select Color Temp from the Display Color menu to adjust the color temperature. The default setting is appropriate for most situations. Higher settings produce a “bluer” picture.

•Lamp Power: Select Lamp Power from the Display Color menu to adjust the lamp output level. You can choose to run the lamp as bright as possible (“1”) or you can choose the lower setting (“0”). Generally, lower lamp output can prolong the life of the lamp, but decreases brightness.

Calibration

Calibration

ISF Night

Display Color

Input Image

Input Color

ISF Day

Display Color

Input Image

Input Color

Save ISF Settings

Output Shift

Splash Configure

OSD Position

Runco VX-2000d Owner’s Operating Manual

47

Page 58 Page 60
Image 59
Page 58 Page 60
Contents VX-2000d Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation On-Screen Menus for 1080i Digital or 1080p Signals Table of Contents List of Figures List of Figures Xii About This Manual IntroductionDegrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental informationFormat screen Description, Features and BenefitsOptional Accessories VX-2000d at a Glance Controls and FunctionsVertical Lens Shift VX-2000d Rear Panel Wired IR 3.5-mm, mini phono jackRS-232C Input RJ-11 female connector More information about aspect ratios, refer to Table DHD Controller Front PanelEnter Button Inputs 2. Hdmi 1 / Hdmi 2 Digital Component Video RCA connectorsDHD Controller Rear Panel Outputs 1. Hdmi OUTComLink RS-232 Output Video 1 / S-VIDEOVolt 750 mA Trigger Outputs DHD Controller/VX-2000d Remote Control VX-2000d Remote Control UnitVideo On / OFFCursor Buttons Menu button see below to exit the menuLetbox Letterbox Memory Preset ButtonsAspect Ratio Selection Buttons 16 9Not used Only trained service personnel should use the built-inVX-2000d Built-In Keypad Controls and Functions Operation InstallationRemote Control Battery InstallationOther surfaces Projector calibration Analog 1080i Lower-resolution signals Quick SetupInstallation specialist Step Procedure For Details, Refer toAmbient Light InstallationInstallation Type ConsiderationsThrow Distance Position Ceiling InstallationFloor Installation Vertical and HorizontalOther Considerations Folded OpticsVX-2000d MountingConnections to the VX-2000d and DHD Controller You Cannot connect signal sources directly to the VX-2000dHdmi Connections See Figure Connecting SourceComponents to the DHD ControllerDigital DTV RGB or Component Video Connections Digital DTV RGB or Component Video Connections See FigurePersonal Computer Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Composite/S-Video/Component Video Connections See FigureDHD Controller Connecting a PC orConnecting 12-Volt Automation System toBuilt-in IR sensor on the DHD Controller is disabled Connecting an External IR Receiver to the DHD ControllerYou must enter a passcode to access the Service menu Turning on the PowerAdjusting the Picture Orientation Connecting to AC PowerVertical Lens Shift Primary Lens AdjustmentsFocus and Zoom It is extremely important that the primary lens is properly Installing and Adjusting the CineWide Anamorphic LensAdjusting the Lens Height Y Installation Operation Aspect Ratio ISF PresetsService Input SourceAspect Ratio Main MenuInput Source Aspect Ratio Description Aspect Ratio SettingsPicture Brightness Contrast Color Tint Sharpness PictureTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Left/Right Up/Down Width Height Overscan Input PositionSerial Num Hardware Firmware 0100.061A Date Apr 30 ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default InformationCalibration You must enter a passcode to access the Calibration menuLow-lights Offset provides finer adjustment Gain/Offset Refer to ISF Night Display Color, above Input Names Restore Composite Video Component SD ServiceExit Auto ADC Bandwidth Auto YPbPr Input ResolutionUse this control to fine-tune the image geometry on a HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUVOperation On-Screen Menus for 1080i Digital or 1080p Signals Runco Video Language Picture AdjustDAY Mpeg NR Picture Adjust AdvancedEffects of Primary Color Hue Adjustments White Balance White BalanceLamp Hours read-onlyRefer to Lamp Hours on Image Shift and Subtitle can only be adjusted for certainOptions Below to Off, the LED function is automatically set to OnRefer to page 60 is automatically set to On OSD Language setting Orientation Refer to Adjusting the Picture Orientation onLamp Replacement Maintenance and TroubleshootingSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Maintenance and Troubleshooting Value Description Min/max Stored? Power On/Off Commands RS-232 Connection and Port ConfigurationSerial Command Syntax CommandAspect Ratio Commands Brightness Iheight Bkgnd Enter key Command Parameter min/max Value Stored? DescriptionVX-2000d Specifications SpecificationsDimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power RequirementsDHD Controller Specifications VX-2000d/CineWide Dimensions VX-2000d DimensionsPage Runco CL-810 Owner’s Operating Manual RUMA-009330 Rev 05-25-07
Related manuals
Manual 88 pages 1.71 Kb

VX-2000d specifications

The Runco VX-2000d is a premium home theater projector that combines cutting-edge technology with a commitment to delivering extraordinary image quality. Renowned among enthusiasts for its exceptional performance, the VX-2000d caters to both the casual viewer and the most discerning cinephile, making it a standout option in the world of home entertainment.

One of the primary features of the Runco VX-2000d is its native 1080p resolution, which ensures that images are crisp, detailed, and vibrant. With a resolution of 1920 x 1080 pixels, this projector capitalizes on High Definition content, enabling viewers to experience movies and shows as the directors intended. Coupled with high brightness levels and a remarkable contrast ratio, the VX-2000d exhibits deep blacks and brilliant colors, enhancing the overall viewing experience.

The VX-2000d incorporates advanced DLP (Digital Light Processing) technology that provides remarkable color accuracy and consistency across a variety of content. The use of the latest imaging chips and sophisticated optics creates lifelike imagery that draws viewers into the action. Additionally, this projector supports a wide color gamut, allowing it to reproduce a broader range of colors for enhanced realism.

Another highlight of the Runco VX-2000d is its sophisticated lens system. The projector features a high-quality glass lens that minimizes optical distortion while ensuring sharp focus across the entire image. Its motorized lens shift, zoom, and focus functionalities allow for easy installation and flexibility in positioning the projector within various home theater setups.

The VX-2000d also supports various video formats, including 24p film and 1080p/60, making it versatile for different types of content. Also, with its built-in proprietary video processing technology, the projector upscales standard-definition and high-definition content to optimized viewing experiences.

Furthermore, the Runco VX-2000d is equipped with a range of connectivity options, including HDMI, Component, and VGA inputs, ensuring compatibility with numerous devices such as Blu-ray players, gaming consoles, and streaming devices.

With its combination of excellent build quality, robust performance, and impressive features, the Runco VX-2000d remains a top choice for enthusiasts seeking an unparalleled home theater experience. Whether enjoying action-packed films or serene nature documentaries, this projector immerses viewers in a cinematic journey that captivates the senses.
Top Page Image Contents