Runco VX-2000d manual Brightness

Page 81

Serial Communications

Table 6-1. Serial Commands (continued)

	Command	Parameter	Value	Description
	Command	(min/max)	Stored?	Description
		(min/max)	Stored?

	Picture Adjust Commands (not available on HDMI 1 or HDMI 2 inputs)

	BRIGHTNESS	-100/100	YES	Sets a value for brightness

	BRIGHTNESS?	NA	NA	Returns brightness setting value

	CHROMADELAY	-12/12	YES	Sets a value for input color chroma delay

	CHROMADELAY?	NA	NA	Returns input color chroma delay setting

	COLOR	-100/100	YES	Sets a value for color

	COLOR?	NA	NA	Returns color setting value

	CONTRAST	-100/100	YES	Sets a value for contrast

	CONTRAST?	NA	NA	Returns contrast setting value

	FILMMODE	0/1	YES	Sets Film Mode off (0) or on (1)

	FILMMODE?	NA	NA	Returns Film Mode setting (0 = off; 1 = on)

	FILTER	0/15	YES	Sets a value for input color noise filter

	FILTER?	NA	NA	Returns input color noise filter setting

	PHASE	0/3	YES	Adjusts phase

	PHASE?	NA	NA	Returns phase setting value

	SHARPNESS	-6/6	YES	Sets a value for sharpness

	SHARPNESS?	NA	NA	Returns sharpness setting value

	TINT	-100/100	YES	Sets a value for tint

	TINT?	NA	NA	Returns tint setting value

	Image Preset Commands (not available on HDMI 1 or HDMI 2 inputs)

	CUSTOM1	NA	YES	Loads “Custom 1” image preset

	CUSTOM2	NA	YES	Loads “Custom 2” image preset

	DAY	NA	YES	Loads “ISF Day” image preset

	NIGHT	NA	YES	Loads “ISF Night” image preset

	PRESET?	NA	NA	Returns currently-selected preset
				(ISF Day, ISF Night, Custom 1 or Custom 2)

Runco VX-2000d Owner’s Operating Manual

69

Image 81

Contents VX-2000d Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation On-Screen Menus for 1080i Digital or 1080p Signals Table of Contents List of Figures List of Figures Xii About This Manual IntroductionCertain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionFormat screen Description, Features and BenefitsOptional Accessories VX-2000d at a Glance Controls and FunctionsVertical Lens Shift Wired IR 3.5-mm, mini phono jack RS-232C Input RJ-11 female connectorVX-2000d Rear Panel More information about aspect ratios, refer to Table DHD Controller Front PanelEnter Button DHD Controller Rear Panel Component Video RCA connectorsOutputs 1. Hdmi OUT Inputs 2. Hdmi 1 / Hdmi 2 DigitalVideo 1 / S-VIDEO Volt 750 mA Trigger OutputsComLink RS-232 Output DHD Controller/VX-2000d Remote Control VX-2000d Remote Control UnitCursor Buttons On / OFFMenu button see below to exit the menu VideoAspect Ratio Selection Buttons Memory Preset Buttons16 9 Letbox LetterboxOnly trained service personnel should use the built-in VX-2000d Built-In KeypadNot used Controls and Functions Remote Control InstallationBattery Installation OperationOther surfaces Installation specialist Quick SetupStep Procedure For Details, Refer to Projector calibration Analog 1080i Lower-resolution signalsInstallation Type InstallationConsiderations Ambient LightThrow Distance Floor Installation Ceiling InstallationVertical and Horizontal PositionOther Considerations Folded OpticsVX-2000d MountingConnections to the VX-2000d and DHD Controller You Cannot connect signal sources directly to the VX-2000dComponents to the DHD Connecting SourceController Hdmi Connections See FigureDigital DTV RGB or Component Video Connections Digital DTV RGB or Component Video Connections See FigurePersonal Computer Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Composite/S-Video/Component Video Connections See FigureConnecting 12-Volt Connecting a PC orAutomation System to DHD ControllerBuilt-in IR sensor on the DHD Controller is disabled Connecting an External IR Receiver to the DHD ControllerAdjusting the Picture Orientation Turning on the PowerConnecting to AC Power You must enter a passcode to access the Service menuPrimary Lens Adjustments Focus and ZoomVertical Lens Shift It is extremely important that the primary lens is properly Installing and Adjusting the CineWide Anamorphic LensAdjusting the Lens Height Y Installation Operation Service ISF PresetsInput Source Aspect RatioMain Menu Input SourceAspect Ratio Aspect Ratio Description Aspect Ratio SettingsPicture Brightness Contrast Color Tint Sharpness PictureTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Left/Right Up/Down Width Height Overscan Input PositionISF Presets ISF Night ISF Day Custom Save Factory Default ISF PresetsInformation Serial Num Hardware Firmware 0100.061A Date Apr 30You must enter a passcode to access the Calibration menu Low-lights Offset provides finer adjustmentCalibration Gain/Offset Refer to ISF Night Display Color, above Input Names Restore Composite Video Component SD ServiceExit Use this control to fine-tune the image geometry on a ADC Bandwidth Auto YPbPr Input ResolutionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV AutoOperation On-Screen Menus for 1080i Digital or 1080p Signals Runco Video Language Picture AdjustDAY Mpeg NR Picture Adjust AdvancedEffects of Primary Color Hue Adjustments White Balance White BalanceOptions Image Shift and Subtitle can only be adjusted for certainBelow to Off, the LED function is automatically set to On Lamp Hours read-onlyRefer to Lamp Hours onRefer to page 60 is automatically set to On OSD Language setting Orientation Refer to Adjusting the Picture Orientation onLamp Replacement Maintenance and TroubleshootingSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port ConfigurationCommand Value Description Min/max Stored? Power On/Off CommandsAspect Ratio Commands Brightness Iheight Bkgnd Enter key Command Parameter min/max Value Stored? DescriptionVX-2000d Specifications SpecificationsIndustry-Standard Specifications Home Theater Calibration SpecificationsPower Requirements DimensionsDHD Controller Specifications VX-2000d/CineWide Dimensions VX-2000d DimensionsPage Runco CL-810 Owner’s Operating Manual RUMA-009330 Rev 05-25-07

Related manuals

Manual 88 pages 1.71 Kb