Runco VX-2000d manual Troubleshooting Tips, Symptom Possible Causes Solution

Page 76

Maintenance and Troubleshooting

5.2

Troubleshooting Tips

Table 5-1provides some general guidelines for troubleshooting problems you may encounter with the VX-2000d.

If you encounter an issue not described here or in Section 3 (refer to Installation Considerations on page 20), or if the suggested solutions fail to resolve the problem,

please contact your Runco dealer or Runco Technical Support.

Table 5-1. Troubleshooting Chart

Symptom

Possible Cause(s)

Solution

The projector does not turn on after initial installation. The power LED on the front of the DHD Controller lights red after you press the power button.

The projector and DHD Controller are both on, but there is no picture and on-screen menus do not appear.

•The VX-2000d is not plugged in or the AC outlet is not active.

•The serial connection from the DHD Controller to the VX-2000d is incorrect.

•The remote control batteries have run out.

•Faulty or incorrect video connection between the DHD Controller and the VX-2000d.

•Ensure that the VX-2000d is plugged in and that the AC outlet is active.

•Ensure that the RS-232 output from the DHD Controller is properly connected to the RS-232C port on the VX-2000d (see Figure 3-6).

•Replace the batteries.

•Ensure that the HDMI output from the DHD Controller is properly connected to the HDMI input on the VX-2000d (see Figure 3-6).

The projector and

•

Incorrect source selection.

• Select the correct source.

DHD Controller are both on

• Source component is not

• Turn on the source.

and menus appear

 

turned on.

 

on-screen, but there is no

•

Source component is

• Check video connections

picture.

 

connected incorrectly or

to source component.

 

 

not at all.

 

 

 

 

 

A projected image from a DVD is split or otherwise scrambled.

Image is too bright and/or lacks definition in the bright areas of the image.

•DVD player is connected to the Component input and set to progressive scan mode.

•Contrast is set too high.

•Turn off progressive scan on the DVD player. Or, connect the DVD player to the HD1 or HD2 input.

•Lower the contrast setting.

Image appears “washed out”

• Brightness is set too high.

• Lower the brightness

and/or dark areas appear too

 

setting.

bright.

 

 

 

 

 

Colors in the image are

• The Red/Pr, Green/Y or

• Ensure that the source

swapped (for example, reds

Blue/Pb outputs from the

outputs are connected to

appear blue or vice versa) on

source are connected to

the correct DHD Controller

one or more sources.

the wrong inputs on the

input.

 

DHD Controller.

 

 

 

 

64

Runco VX-2000d Owner’s Operating Manual

Page 75 Page 77
Image 76
Page 75 Page 77
Contents VX-2000d Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation On-Screen Menus for 1080i Digital or 1080p Signals Table of Contents List of Figures List of Figures Xii Introduction About This ManualUsing This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Format screenOptional Accessories Controls and Functions VX-2000d at a GlanceVertical Lens Shift RS-232C Input RJ-11 female connector Wired IR 3.5-mm, mini phono jackVX-2000d Rear Panel DHD Controller Front Panel More information about aspect ratios, refer to TableEnter Button Component Video RCA connectors DHD Controller Rear PanelOutputs 1. Hdmi OUT Inputs 2. Hdmi 1 / Hdmi 2 DigitalVolt 750 mA Trigger Outputs Video 1 / S-VIDEOComLink RS-232 Output VX-2000d Remote Control Unit DHD Controller/VX-2000d Remote ControlOn / OFF Cursor ButtonsMenu button see below to exit the menu VideoMemory Preset Buttons Aspect Ratio Selection Buttons16 9 Letbox LetterboxVX-2000d Built-In Keypad Only trained service personnel should use the built-inNot used Controls and Functions Installation Remote ControlBattery Installation OperationOther surfaces Quick Setup Installation specialistStep Procedure For Details, Refer to Projector calibration Analog 1080i Lower-resolution signalsInstallation Installation TypeConsiderations Ambient LightThrow Distance Ceiling Installation Floor InstallationVertical and Horizontal PositionFolded Optics Other ConsiderationsMounting VX-2000dYou Cannot connect signal sources directly to the VX-2000d Connections to the VX-2000d and DHD ControllerConnecting Source Components to the DHDController Hdmi Connections See FigureDigital DTV RGB or Component Video Connections See Figure Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnecting a PC or Connecting 12-VoltAutomation System to DHD ControllerConnecting an External IR Receiver to the DHD Controller Built-in IR sensor on the DHD Controller is disabledTurning on the Power Adjusting the Picture OrientationConnecting to AC Power You must enter a passcode to access the Service menuFocus and Zoom Primary Lens AdjustmentsVertical Lens Shift Installing and Adjusting the CineWide Anamorphic Lens It is extremely important that the primary lens is properlyAdjusting the Lens Height Y Installation Operation ISF Presets ServiceInput Source Aspect RatioInput Source Main MenuAspect Ratio Aspect Ratio Settings Aspect Ratio DescriptionPicture Picture Brightness Contrast Color Tint SharpnessTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanISF Presets ISF Presets ISF Night ISF Day Custom Save Factory DefaultInformation Serial Num Hardware Firmware 0100.061A Date Apr 30Low-lights Offset provides finer adjustment You must enter a passcode to access the Calibration menuCalibration Gain/Offset Refer to ISF Night Display Color, above Service Input Names Restore Composite Video Component SDExit ADC Bandwidth Auto YPbPr Input Resolution Use this control to fine-tune the image geometry on aHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV AutoOperation On-Screen Menus for 1080i Digital or 1080p Signals Runco Video Picture Adjust LanguageDAY Picture Adjust Advanced Mpeg NREffects of Primary Color Hue Adjustments White Balance White BalanceImage Shift and Subtitle can only be adjusted for certain OptionsBelow to Off, the LED function is automatically set to On Lamp Hours read-onlyRefer to Lamp Hours onRefer to page 60 is automatically set to On Orientation Refer to Adjusting the Picture Orientation on OSD Language settingMaintenance and Troubleshooting Lamp ReplacementTroubleshooting Tips Symptom Possible Causes SolutionTroubleshooting Chart Maintenance and Troubleshooting RS-232 Connection and Port Configuration Serial Command SyntaxCommand Value Description Min/max Stored? Power On/Off CommandsAspect Ratio Commands Brightness Iheight Bkgnd Command Parameter min/max Value Stored? Description Enter keySpecifications VX-2000d SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsDHD Controller Specifications VX-2000d Dimensions VX-2000d/CineWide DimensionsPage RUMA-009330 Rev 05-25-07 Runco CL-810 Owner’s Operating Manual
Related manuals
Manual 88 pages 1.71 Kb

VX-2000d specifications

The Runco VX-2000d is a premium home theater projector that combines cutting-edge technology with a commitment to delivering extraordinary image quality. Renowned among enthusiasts for its exceptional performance, the VX-2000d caters to both the casual viewer and the most discerning cinephile, making it a standout option in the world of home entertainment.

One of the primary features of the Runco VX-2000d is its native 1080p resolution, which ensures that images are crisp, detailed, and vibrant. With a resolution of 1920 x 1080 pixels, this projector capitalizes on High Definition content, enabling viewers to experience movies and shows as the directors intended. Coupled with high brightness levels and a remarkable contrast ratio, the VX-2000d exhibits deep blacks and brilliant colors, enhancing the overall viewing experience.

The VX-2000d incorporates advanced DLP (Digital Light Processing) technology that provides remarkable color accuracy and consistency across a variety of content. The use of the latest imaging chips and sophisticated optics creates lifelike imagery that draws viewers into the action. Additionally, this projector supports a wide color gamut, allowing it to reproduce a broader range of colors for enhanced realism.

Another highlight of the Runco VX-2000d is its sophisticated lens system. The projector features a high-quality glass lens that minimizes optical distortion while ensuring sharp focus across the entire image. Its motorized lens shift, zoom, and focus functionalities allow for easy installation and flexibility in positioning the projector within various home theater setups.

The VX-2000d also supports various video formats, including 24p film and 1080p/60, making it versatile for different types of content. Also, with its built-in proprietary video processing technology, the projector upscales standard-definition and high-definition content to optimized viewing experiences.

Furthermore, the Runco VX-2000d is equipped with a range of connectivity options, including HDMI, Component, and VGA inputs, ensuring compatibility with numerous devices such as Blu-ray players, gaming consoles, and streaming devices.

With its combination of excellent build quality, robust performance, and impressive features, the Runco VX-2000d remains a top choice for enthusiasts seeking an unparalleled home theater experience. Whether enjoying action-packed films or serene nature documentaries, this projector immerses viewers in a cinematic journey that captivates the senses.
Top Page Image Contents