Vidikron 40828 manual Safety Precautions

Page 6

Safety Precautions

Thank you for your purchase of this quality Vidikron video projector! It has been designed to provide you with the quality of video that is expected in a home theater. For the best performance, please read this manual carefully as it is your guide through the menus and operation.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

WARNING

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Do not use this equipment near water, outdoors or otherwise exposed to the elements.

5.Clean only with a dry cloth.

6.Do not block any ventilation openings.

7.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

8.Do not defeat the safety feature of the polarized or grounding type plug. A polarized type plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.

9.The 12V trigger only outputs DC 12V signal for triggering. Do not connect to any other power input or output. This could cause damage to this unit.

10.Only use accessories specified by Vidikron.

11.Keep the packing material in case the equipment should ever need to be shipped.

12.Unplug this projector during lightning storms or when it will not be used for an extended period of time.

13.The lamp becomes extremely hot during operation. Allow the projector to cool down for approximately 45 minutes prior to removing the lamp assembly for replacement. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps beyond rated life could cause them to explode in rare occasions.

14.Refer all servicing to qualified service personnel. Servicing is required when the projector has been damaged in any way, objects have fallen or spilled into the projector, the projector has been exposed to rain or moisture, does not operate normally, or has been dropped.

vi

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Image 6
Contents 10/12 Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Operation Maintenance and TroubleshootingSpecifications Serial Communications1List of Figures List of Figures 1Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories 2Controls and Functions Vision 10/12 at a GlanceFront/Top/Side View Vidikron Logo Vertical Lens Shift Dial Shifts the image up or downRear/Top/Side View Vision 10/12 Rear/Top/Side ViewLamp Cover Exhaust Vent Vision 10/12 Remote Control Vision 10/12 Remote ControlISF DAY Light Controls and Functions 3Installation Remote ControlAvailable Range of the Remote Control OperationQuick Setup Installation OverviewStep Procedure For Details, refer to Installation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsEstimating Throw Distance TD Vertical and Horizontal Horizontal Lens Shift Angle Adjusting the ProjectionVertical and Horizontal Lens Shift Limits VisionFolded Optics Connector Panel Access Connections to the Vision 10/12To Source Components DVI Source Connections Hdmi Source Connections Analog RGB Connections 10. Component Video Connections Connection Trigger OutputInstallation Turning on the Power Adjusting the Projector Height or Projection Angle4Operation Changing the OSD Language Adjusting the Picture Orientation Lens Adjustments Focus/ZoomUsing the On-Screen Menus Cause the projector to malfunctionVision 10/12 OSD Menu Structure ISF Setting Main Menu Source SelectAspect Ratio Aspect Ratio Settings Control DescriptionRGB-HD Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Effect of X and Y Coordinates for Color Temperature AdjustmentImage Option Auto Tune may take some time to complete, depending on Installation Horizontal Keystone Correction Vertical Keystone CorrectionISF Setting ISF Calibration11. ISF-Enabled Vision 10/12 Splash Screen Blue Enable Refer to Blue Enable on 5Maintenance and Troubleshooting Cleaning the Projector Cleaning the LensCleaning the Intake and Exhaust Vents Lamp Maintenance Lamp CautionsLamp Replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Maintenance and Troubleshooting Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration Command Description ReplySerial Communications 7Specifications Vision 10/12 SpecificationsWeight including lens Power RequirementsDimensions Home Theater Calibration SpecificationsVision 10/12 Dimensions 1shows the Vision 10/12 dimensionsResolution Computer Signal CompatibilityComputer Signal Compatibility Chart Horizontal VerticalDisplay Freq Compatible Inputs Note Resolution Video Signal CompatibilityVideo Signal Compatibility Chart CompPage RUMA-011175