Vidikron 40828 Troubleshooting Tips, Troubleshooting Chart, Symptom Possible Causes Solution

Page 63

Maintenance and Troubleshooting

Table 5-1provides some general guidelines for troubleshooting problems you may encounter with the Vision 10/12. If you encounter an issue not described here, please contact your Vidikron dealer or Vidikron Technical Support.

Table 5-1. Troubleshooting Chart

Symptom

 

Possible Cause(s)

Solution

 

 

 

 

The projector does not turn on

The Vision 10/12 is not

• Ensure that the Vision

after initial installation.

 

plugged in or the AC outlet

10/12 is plugged in and

 

 

is not active.

that the AC outlet is active.

 

The remote control

• Replace the batteries.

 

 

batteries have run out.

 

 

 

 

 

The projector is on, but there is

Incorrect source selection.

• Select the correct source.

no video image on-screen.

Source component is not

• Turn on the source

 

 

turned on.

component.

 

 

 

 

A projected image from a DVD

DVD player is set to

• Turn off progressive scan

is split or otherwise scrambled.

 

progressive scan mode.

on the DVD player.

 

 

 

• Connect the DVD player to

 

 

 

the HD/RGB 1 or HD/RGB 2

 

 

 

input.

 

 

 

 

5.7

Troubleshooting Tips

Image is too bright and/or

• Contrast is set too high.

lacks definition in the bright

 

areas of the image.

 

Image appears “washed out”

• Brightness is set too high.

and/or dark areas appear too

 

bright.

 

Colors in the image are

• The Red/Pr, Green/Y or

swapped; for example, reds

Blue/Pb outputs from the

appear blue or vice versa.

source are connected to the

 

wrong inputs on the Vision

 

10/12.

RGB-HD images appear

• Clock and Phase settings

“noisy.”

need adjustment.

The projector will not turn

• The projector will not turn

back on after it was powered

on for two minutes after

down, or the image disappears

power-down, to protect the

during operation.

lamp.

 

• The lamp has failed or was

 

improperly installed.

Lower the contrast setting.

Lower the brightness setting.

Ensure that the source outputs are connected to the correct Vision 10/12 input.

Manually adjust Clock and Phase settings, or perform an Auto-Tune (refer to HD/RGB Adjust on page 42).

Wait until the cooling fan stops.

Replace or re-install the lamp.

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

53

Image 63
Contents 10/12 Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Serial Communications Maintenance and TroubleshootingSpecifications Operation1List of Figures List of Figures About This Manual 1IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories 2Controls and Functions Vision 10/12 at a GlanceFront/Top/Side View Vertical Lens Shift Dial Shifts the image up or down Vidikron LogoVision 10/12 Rear/Top/Side View Rear/Top/Side ViewLamp Cover Exhaust Vent Vision 10/12 Remote Control Vision 10/12 Remote ControlISF DAY Light Controls and Functions Remote Control 3InstallationOperation Available Range of the Remote ControlQuick Setup Installation OverviewStep Procedure For Details, refer to Advantages Considerations Installation ConsiderationsProjector Installation Options Installation TypeEstimating Throw Distance TD Vertical and Horizontal Horizontal Lens Shift Vision Adjusting the ProjectionVertical and Horizontal Lens Shift Limits AngleFolded Optics Connector Panel Access Connections to the Vision 10/12To Source Components DVI Source Connections Hdmi Source Connections Analog RGB Connections 10. Component Video Connections Trigger Output ConnectionInstallation Turning on the Power Adjusting the Projector Height or Projection Angle4Operation Changing the OSD Language Adjusting the Picture Orientation Focus/Zoom Lens AdjustmentsCause the projector to malfunction Using the On-Screen MenusVision 10/12 OSD Menu Structure ISF Setting Main Menu Source SelectAspect Ratio Control Description Aspect Ratio SettingsRGB-HD Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Adjustment Effect of X and Y Coordinates for Color TemperatureImage Option Auto Tune may take some time to complete, depending on Installation Vertical Keystone Correction Horizontal Keystone CorrectionISF Calibration ISF Setting11. ISF-Enabled Vision 10/12 Splash Screen Blue Enable Refer to Blue Enable on Cleaning the Projector Cleaning the Lens 5Maintenance and TroubleshootingCleaning the Intake and Exhaust Vents Lamp Cautions Lamp MaintenanceLamp Replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Maintenance and Troubleshooting Command Description Reply Serial Command SyntaxRS-232 Connection and Port Configuration Serial CommandsSerial Communications Vision 10/12 Specifications 7SpecificationsHome Theater Calibration Specifications Power RequirementsDimensions Weight including lens1shows the Vision 10/12 dimensions Vision 10/12 DimensionsHorizontal Vertical Computer Signal CompatibilityComputer Signal Compatibility Chart ResolutionDisplay Comp Video Signal CompatibilityVideo Signal Compatibility Chart Freq Compatible Inputs Note ResolutionPage RUMA-011175