Vidikron 40828 manual Changing the OSD Language Adjusting the Picture Orientation

Page 40

Operation

4.3

Changing the OSD Language

4.4

Adjusting the Picture Orientation

The Vision 10/12 OSD language is initially set to English, but can also display the menus in French, Italian, German or Spanish. To change the OSD language:

1.Press MENU.

2.Select Installation from the Main Menu.

3.Select Language from the Installation Menu.

4.Press or to select the desired language. The change takes effect immediately.

By default, the Vision 10/12 is configured for a “floor/front” installation, in which the projector is installed upright and in front of the screen. If it is installed behind the screen and/or mounted on a ceiling, you must change the picture orientation. To do this:

1.Press MENU.

2.Select Installation from the Main Menu.

3.Select Picture Configuration from the Installation Menu.

4.Choose Floor Rear, Ceiling Front or Ceiling Rear, to match the installation method.

30

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Image 40
Contents 10/12 Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Maintenance and Troubleshooting SpecificationsOperation Serial Communications1List of Figures List of Figures 1Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Vision 10/12 at a Glance 2Controls and FunctionsFront/Top/Side View Vidikron Logo Vertical Lens Shift Dial Shifts the image up or downRear/Top/Side View Vision 10/12 Rear/Top/Side ViewLamp Cover Exhaust Vent Vision 10/12 Remote Control Vision 10/12 Remote ControlISF DAY Light Controls and Functions 3Installation Remote ControlAvailable Range of the Remote Control OperationInstallation Overview Quick SetupStep Procedure For Details, refer to Installation Considerations Projector Installation OptionsInstallation Type Advantages ConsiderationsEstimating Throw Distance TD Vertical and Horizontal Horizontal Lens Shift Adjusting the Projection Vertical and Horizontal Lens Shift LimitsAngle VisionFolded Optics Connections to the Vision 10/12 Connector Panel AccessTo Source Components DVI Source Connections Hdmi Source Connections Analog RGB Connections 10. Component Video Connections Connection Trigger OutputInstallation Adjusting the Projector Height or Projection Angle Turning on the Power4Operation Changing the OSD Language Adjusting the Picture Orientation Lens Adjustments Focus/ZoomUsing the On-Screen Menus Cause the projector to malfunctionVision 10/12 OSD Menu Structure ISF Setting Source Select Main MenuAspect Ratio Aspect Ratio Settings Control DescriptionRGB-HD Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Effect of X and Y Coordinates for Color Temperature AdjustmentImage Option Auto Tune may take some time to complete, depending on Installation Horizontal Keystone Correction Vertical Keystone CorrectionISF Setting ISF Calibration11. ISF-Enabled Vision 10/12 Splash Screen Blue Enable Refer to Blue Enable on 5Maintenance and Troubleshooting Cleaning the Projector Cleaning the LensCleaning the Intake and Exhaust Vents Lamp Maintenance Lamp CautionsLamp Replacement Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands Command Description ReplySerial Communications 7Specifications Vision 10/12 SpecificationsPower Requirements DimensionsWeight including lens Home Theater Calibration SpecificationsVision 10/12 Dimensions 1shows the Vision 10/12 dimensionsComputer Signal Compatibility Computer Signal Compatibility ChartResolution Horizontal VerticalDisplay Video Signal Compatibility Video Signal Compatibility ChartFreq Compatible Inputs Note Resolution CompPage RUMA-011175